APM 2.8 Flight Controller with In-Built Compass

Female to Female Jumper Wires (20cm) 40pcs These are 20cm 40pcs Female to Female Jumper wires, very Flexible and easily detachable. These jumper cables have 1Pin female to the 1pin female header with both ends. Also, it is compatible with 2.54 mm mil spacing pin headers. This cable is an electrical wire or group of them in a cable with a connector or pins at each end, which is normally for interconnecting the components of a breadboard or other prototype or test circuit, internally or with other equipment or components, without soldering. Individual Dupont Cables are fitted by inserting their end connectors into the slots provided in a breadboard, the header connector of a circuit board, or a piece of test equipment. Mostly Dupont cables are useful with Orange Pi, Banana Pi, Raspberry Pi , Arduino , and other mini PCs and development boards . It is very useful in the PCB project, PC motherboard, as well as Breadboard connections. Additionally, these jumper wires allows you to plug and unplug easily for prototyping and can be used over and over again. Check out the best selection of Jumper Wires . Applications: Raspberry Pi Arduino PCB projects Breadboard connections Get a complete set of M2M, M2F, F2F Jumper Wires Set for DIY projects.

A3967 Stepper Motor Driver This A3967 Stepper Motor Driver For Arduino is the most recent version of EasyDriver v44, which was created in collaboration with Brian Schmalz. When compared to previous versions, it offers more flexibility and control over your stepper motor . It is a simple stepper motor driver that is compatible with most microcontrollers and capable of producing a digital 0 to 5V pulse (0 to 3.3V pulse if you solder SJ2 closed on the EasyDriver). A 7V to 30V power supply is required for the module's motor. The digital interface is powered by an onboard voltage regulator that can be set to 5V or 3.3V. The A3967 is a full-featured microstepping motor driver with an integrated transistor. It is intended for use with bipolar stepper motors in full-, half-, quarter-, and eighth-step modes, with output drive capabilities of 30 V and 750 mA. The A3967 comes with a fixed off-time current regulator that can operate in slow, fast, or mixed current-decay modes. This current-decay control scheme produces less audible motor noise, higher step accuracy, and lower power dissipation. The transistor is essential to the A3967's simple implementation. Simply sending one pulse to the STEP input causes the motor to move one step (full, half, quarter, or eighth depending on two logic inputs). It is not necessary to programme phase-sequence tables, high-frequency control lines, or complex interfaces. The A3967 interface is ideal for applications where a complex P is either unavailable or overburdened. Features: A3967 microstepping driver Adjustable current control from 150mA/phase to 750mA/phase MS1 and MS2 pins are broken out to change microstepping resolution to full, half, quarter and eighth steps (defaults to eighth) Compatible with 4, 6, and 8-wire stepper motors of any voltage Breadboard-compatible pins.

CNC Shield for Arduino The CNC shield for Arduino has total four slots, can drive 4 A4988 stepper motors. Each road stepper motors only need two IO ports. In other words, six IO ports can be well managed three stepper motors. The CNC Shield V3.0 allows you to build a engraving machine, 3D printer, mini CNC and other similar devices using your Arduino. It is designed as a shield and can plug on top of an Arduino requiring no external connections and wiring. There are 4 slots on the board for plugging in stepper motor drive module which can drive 1 stepper motor each. Controlling each step stepper motor requires only two IO pins on the Arduino. Just insert this Arduino CNC Shield V3.0 onto an Arduino UNO , and install the GRBL firmware, you can then quickly build a DIY CNC engraving machine. This arduino shield is very convenient to use and is suitable for development boards compatible with Arduino. This CNC shield compatible with Arduino is the latest version of the CN shield model (V 3.0). The CNC Shield is GRBL 0.9 compatible and with the help of jumper wires , it is accessible to stepper drivers. Features: Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place. GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals) 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)

CNC Shield + UNO R3 Board compatible with Arduino + 4xDRV8825 Driver Kit Arduino Uno is an open-source microcontroller used by students and hobbyists entering the world of DIY electronics and automation, The Arduino Uno can be used for any application including being the brains of your next DIY 3D printer and/or CNC router The CNC Shield V3.0 allows you to build an engraving machine, 3D printer, mini CNC and other similar devices using your Arduino. It is designed as a shield and can plug on top of an Arduino requiring no external connections and wiring. Along with that, the CNC shield allows you to control up to four stepper motors by mounting on 4 stepper motor drivers, included with this kit The DRV8825 provides an integrated motor driver solution for printers, scanners, and other automated equipment. The device has two H-bridge and is intended to drive a bipolar stepper motor. Features: UNO R3 Board: The main microcontroller board compatible with Arduino. CNC Shield: An expansion board that allows for easy connection and control of stepper motors. 4x DRV8825 Stepper Motor Drivers: High-performance drivers for controlling stepper motors. Micro-Stepping: Supports micro-stepping settings for precise control of stepper motors. GRBL Compatibility: Compatible with GRBL firmware, which is widely used for CNC control. Voltage Range: Operates on 12-36V DC. Heat Sinks: Included for cooling the stepper motor drivers. USB Cable: For connecting the UNO R3 board to a computer. 40-Pin Row Needles: For additional connections. Applications: CNC Machines: Used for controlling stepper motors in CNC milling, engraving, and cutting machines. 3D Printers: Essential for driving stepper motors in 3D printers, ensuring precise layer deposition and movement. Laser Cutters: Controls stepper motors in laser cutting machines for accurate cutting and engraving. Robotics: Ideal for robotics projects requiring precise motor control, such as robotic arms and automated guided vehicles (AGVs). X-Y Tables: Used in X-Y tables for accurate positioning and movement in various industrial applications. Pick-and-Place Devices: Employed in pick-and-place machines for accurate component placement in electronics manufacturing. Labeling Machines: Used in labeling machines for precise label application. Pinout Diagram for the Arduino Uno Microcontroller Applications of the Kit The kit can be used to create custom 3D printers, scanner, CNC mills and other automated equipment applications

SmartElex Sound Detection Sensor The SmartElex Sound Detection Sensor is a compact and efficient sound sensor module designed to detect sound presence and measure sound intensity with precision. Built around the LM386 audio amplifier, it provides both analog (AOUT) and digital (DOUT) outputs, making it suitable for a wide range of applications—from simple sound-triggered actions to detailed audio level monitoring. Operating smoothly between 3.3V and 5.3V, this sound sensor Arduino compatible module integrates easily with popular development boards such as Arduino, STM32, and Raspberry Pi. Its low power consumption, small form factor, and included 4-pin cable make it perfect for sound-activated projects, noise detection systems, smart devices, and interactive electronics where reliable audio sensing is required. Features: LM386 audio amplifier for a powerful sound signal enhancement. Detect low-level sounds with 200× amplification. Wide voltage range: 3.3 to 5.3 volts Dual outputs: analog (AOUT) and digital (DOUT). Low power consumption, suitable for embedded systems. Adjustable gain using external components Compact and lightweight; breadboard-friendly. Simple integration with Arduino, STM32, and more.

SmartElex 5V 3A 4 Channel Signal Relay Module The SmartElex 5V 3A 4 Channel Signal Relay Module is a compact and reliable 4 Channel Relay Module designed to control four independent medium-power loads with precision. Powered as a 5V relay module, it integrates high-quality JY4100F-S-DC5V-C relays, each capable of switching up to 3A at 120V AC or 24V DC. With dedicated trigger inputs and LED status indicators for every channel, it allows easy monitoring and accurate switching. This module directly interfaces with popular microcontrollers such as Arduino, ESP8266, and Raspberry Pi, making it ideal for IoT, home automation, and embedded control applications where safety, isolation, and consistent performance are essential. Applications: Home automation (controlled lights, fans, and locks) Industrial machine control IoT multi-device projects. Robotics and Motor Control Security systems and alarms. Cautions: Always utilize a properly regulated 5V power supply. Avoid exceeding the rated load capacity. Provide proper isolation for AC loads. Store the module in a dry, clean place. Features: Four-channel relay module allows for independent control of four devices. Operates at 5V DC and has an active LOW/HIGH trigger. Each relay can handle up to 3A at 120V AC or 24V DC. Compatible with Arduino, ESP8266, Raspberry Pi, and more platforms. Each channel has its own set of LED indicators. Fast switching: ≤10 ms operation and ≤5 ms release time. Low contact resistance (≤100 mΩ) ensures effective operation. The total power consumption is around 1.44W over four channels. High insulation resistance and dielectric strength are essential for safety. Wide operational temperature range (-40°C to +85°C).

7SEMI PT100 RTD Temperature Sensor Probe 2-wire 1m -70~300C The 7SEMI PT100 RTD Temperature Sensor Probe 2-wire 1 m (-70 ~ 300°C) (ES-13519) is a reliable temperature sensor designed to deliver accurate and stable readings across a wide temperature range. It uses a platinum PT100 RTD element, which is well known for precision and long-term consistency, making it suitable for both learning and professional applications. The sensor comes with a 1-meter cable and a sturdy stainless-steel probe that can handle demanding environments. Its simple 2-wire design makes it easy to connect with temperature controllers, data loggers, and microcontroller-based systems. Whether you’re working on industrial monitoring, laboratory experiments, or electronics projects, this PT100 probe offers a good balance of accuracy, durability, and ease of use. Features: Uses a PT100 platinum RTD element for accurate and stable temperature measurement Wide operating temperature range from -70°C to 300°C 2-wire configuration for simple and reliable connectivity Stainless steel probe for durability and long service life Comes with a 1-meter insulated cable for flexible installation Suitable for industrial, laboratory, and electronics projects Provides consistent readings over time with minimal drift

SmartElex BS612 PIR Motion Sensor Module The SmartElex BS612 PIR Motion Sensor Module is a passive infrared motion detection solution designed to sense human movement by detecting changes in infrared radiation. It helps automate electronic systems by enabling actions only when motion is detected, improving efficiency and reducing unnecessary power usage. This module is suitable for students, makers, engineers, educators, and startups who need a reliable motion sensing component for learning projects, prototypes, and embedded system designs. This PIR motion sensor module is commonly used in robotics, IoT devices, security systems, and home or industrial automation projects where accurate motion detection is required. It can be easily interfaced with popular platforms such as Arduino, Raspberry Pi, and ESP32, allowing quick integration into working systems. The wide detection coverage and stable performance make it ideal for applications like motion-activated lighting, alarm systems, smart monitoring solutions, and interactive electronics projects. Features: Passive infrared (PIR) sensor for accurate human motion detection Detects movement by sensing changes in infrared radiation Wide 120° detection angle for broader area coverage Long sensing range suitable for security and automation use Low power consumption for battery-operated projects Compatible with Arduino, Raspberry Pi, ESP32, and similar microcontrollers

7Semi I2C BME680 Sensor Probe Powered by Bosch Sensortec BME680 Sensor The 7Semi BME680 Environmental Sensor Probe is a compact and rugged sensing module designed for high-accuracy air quality monitoring in demanding indoor and industrial environments. Built around the Bosch BME680 multisensor chip, it delivers precise temperature, humidity, barometric pressure, and VOC gas readings over a reliable I2C interface. With its fully calibrated output and fast response time, this probe is ideal for engineers and system designers building smart HVAC controls, home automation setups, or environmental monitoring equipment. Encased in a breathable, chemically resistant plastic shell, the BME680 probe ensures long-term stability even when exposed to dust, high humidity, or harsh atmospheric conditions. The integrated 1-meter cable with a Mini Round Shell connector makes installation easy across ducts, walls, chambers, and compact enclosures. Its low power consumption and wide operating range make it a dependable choice for air quality monitoring projects, IoT systems, and precision sensor applications. Features: Offers 4-in-1 environmental sensing, providing temperature, humidity, barometric pressure, and VOC gas measurements in a compact and efficient module. Utilizes the Bosch BME680 sensor for high accuracy and fast response across a wide range of environmental conditions. Enclosed in a breathable, durable plastic housing that protects the sensor from dust, chemicals, and environmental wear while ensuring excellent air permeability. Supports I2C digital communication for seamless integration with microcontrollers and embedded systems. Includes a 1-meter cable with a Mini Round Shell Plastic connector, enabling flexible installation in tight or industrial spaces. Operates on low voltage (1.71V to 3.6V), making it ideal for energy-efficient and battery-powered applications. Fully factory-calibrated sensor output eliminates the need for manual tuning or recalibration. Designed for reliable performance in pipes, ducts, walls, HVAC units, greenhouses, and high-humidity environments.

SmartElex HTU21D-F Temperature and Humidity Sensor with Breakout Board The SmartElex HTU21D-F Temperature and Humidity Sensor with Breakout Board is a compact and reliable temperature and humidity sensor designed for accurate environmental monitoring. It helps users measure ambient temperature and humidity digitally with stable output, making it suitable for students, makers, educators, and engineers working on sensing and monitoring applications. This digital temperature and humidity sensor is ideal for those who want dependable readings without complex circuitry, especially in learning, testing, and early product development environments. This I2C digital humidity sensor is widely used in IoT systems, weather monitoring projects, automation setups, and data logging applications where consistent environmental data is required. It integrates easily with popular development platforms such as Arduino, Raspberry Pi, and ESP32, allowing quick setup and smooth communication through the I2C interface. With its breakout board design and reliable performance, the SmartElex HTU21D-F sensor is well suited for prototyping, robotics projects, and educational labs looking for a practical alternative to traditional sensors like SHT15 breakout boards. Features: Digital temperature and humidity sensor with stable and accurate readings I2C interface for simple and reliable data communication Compact breakout board for quick prototyping and testing Easy to use with Arduino, Raspberry Pi, and ESP32 platforms Suitable for IoT, automation, and environmental monitoring projects Ideal replacement option for older sensors like SHT15 breakout boards

7Semi DC-DC Buck Converter 14V-60V Input to 5V 3A Output- AP66300 (BO-10189) The 7Semi DC-DC Buck Converter 14V–60V Input to 5V 3A Output – AP66300 (BO-10189) is a compact power module designed to convert high DC input voltages into a stable 5V output with up to 3A current. Its wide input range makes it suitable for applications that use automotive, industrial, or high-voltage power sources. Built on an efficient synchronous buck design, this converter delivers reliable power with low heat generation and minimal energy loss. It is well suited for powering microcontrollers, sensors, communication modules, and other embedded electronics. Whether you’re working on industrial systems, automation projects, or advanced DIY builds, this buck converter provides a dependable and efficient power solution. Features: Wide input range: accepts 14V to 60V DC sources Provides a stable 5V output at up to 3A High-efficiency buck converter design for low energy loss Compact breakout board for easy project use Built-in power protection for safer operation Ideal for automotive, industrial, and embedded electronics Supports powering microcontrollers, sensors, and communication modules Efficient solution for IoT, automation, and high-voltage systems

7Semi BMP581 High-Precision Barometric Pressure & Altitude Sensor Breakout The 7Semi BMP581 Barometric Pressure & Altitude Sensor Breakout is engineered for projects that demand highly accurate atmospheric pressure and altitude data. Built on Bosch’s advanced sensing technology, this compact module delivers exceptional precision with ±30 Pa absolute accuracy and ±6 Pa relative accuracy, translating to altitude precision as fine as ±0.5 meters. Its ability to operate across a wide 300–1250 hPa pressure range makes it ideal for applications like weather stations, environmental monitoring, and UAV altitude tracking. Designed for effortless integration, the BMP581 supports I2C, I3C, and SPI interfaces, making it compatible with a wide range of development boards and embedded systems. The Qwiic connector ensures solder-free wiring, while the low-power operation makes it suitable for portable and battery-powered devices. Whether you're building an IoT sensor node, a smart altimeter, or barometric logging system, this breakout brings reliable performance, high sensitivity, and fast data rates, perfect for altitude measurement and barometric pressure sensing projects. Features: Provides high-precision barometric readings with ±30 Pa absolute accuracy and ±6 Pa relative accuracy for reliable altitude measurement. Offers extremely fine resolution down to 1/64 Pa, ensuring smooth and accurate environmental data output. Includes Qwiic Connect support for solder-free I2C connectivity along with 0.1" header pins for SPI or wired I2C connections. Operates with ultra-low power consumption, only 1.5 µA in deep standby and 260 µA during active measurements. Covers a wide pressure sensing range from 30 to 125 kPa with high output data rates up to 622 Hz for real-time applications. Provides flexible configuration options, including adjustable oversampling, FIFO buffer, and low-pass filtering for optimized performance. Features 6 bytes of onboard non-volatile memory for storing user-specific calibration or configuration data.

SmartElex TEMT6000 Ambient Light Sensor Breakout The SmartElex TEMT6000 Ambient Light Sensor Breakout is a compact sensor module designed to detect ambient light levels and convert them into an analog signal for easy measurement. It helps users sense brightness in the environment without complex circuitry, making it suitable for students, hobbyists, educators, and engineers working on light-responsive projects. As a beginner-friendly module, it is ideal for learning how light sensors work, experimenting with interactive electronics, or integrating illumination detection into early-stage prototypes. This ambient light sensor breakout is commonly used in IoT devices, robotics, display dimming systems, smart lighting, and automation setups where real-time light intensity data is required. It connects smoothly with development boards like Arduino, Raspberry Pi, and ESP32, enabling quick setup and data integration for testing and project development. With stable performance and simple analog output, the SmartElex TEMT6000 is a practical choice for DIY electronics, classroom projects, and embedded product concepts focused on light-based control and automation. Features: Detects ambient light levels and outputs an analog signal Compact breakout board for easy integration into projects Simple interfacing for quick setup and testing Works smoothly with Arduino, Raspberry Pi, and ESP32 Ideal for smart lighting, display dimming, and IoT applications Great for education, prototyping, and light-based automation projects

Radiolink FPV Mobile Phone Holder Stand Folding Mount for RC4GS V3/V2 & RC6GS V3/V2 Controllers The Radiolink FPV Display Monitor Screen Holder is designed to securely hold mobile phones or FPV display screens on your RC controller. Simply insert the mount into the controller’s 1/4” (M6) thread hole, place your phone or monitor on the holder, and adjust the angle using the 360° rotating ball head. This makes it easy to achieve the perfect viewing position while flying, whether indoors or outdoors. This foldable and lightweight holder extends from 5.5cm to 9cm, supporting FPV monitors up to 4.3 inches and mobile phones up to 6.8 inches. Compatible with Radiolink RC4GS V2/V3, RC6GS V2/V3, and other devices with a standard thread hole, it is made of durable plastic and metal to withstand impact. Weighing only 105g, it is easy to install, remove, and carry, making it a reliable accessory for FPV enthusiasts. Features: Holds mobile phones or FPV display monitors securely 360° adjustable ball head for optimal viewing angles Extendable from 5.5cm to 9cm Supports FPV monitors up to 4.3 inches and phones up to 6.8 inches Compatible with Radiolink RC4GS V2/V3, RC6GS V2/V3, and devices with 1/4” (M6) thread hole Lightweight and durable, made of plastic and metal Easy to install, remove, and carry

7Semi MAX31865 PT1000 RTD 3-Wire Temperature Sensor Amplifier Breakout Board The 7Semi MAX31865 PT1000 RTD 3-Wire Temperature Sensor Amplifier Breakout Board is designed for highly accurate temperature measurement using PT1000 sensors. Equipped with the MAX31865 RTD to Digital Converter, it compensates for lead resistance and supports 2, 3, and 4-wire PT1000 configurations, ensuring precise readings. The board easily connects to microcontrollers via SPI and operates at both 3.3V and 5V, making it a versatile solution for industrial, laboratory, and advanced DIY temperature monitoring projects. Features: The PT1000 RTD, a cornerstone of industrial temperature monitoring, provides high accuracy and repeatability, outperforming thermocouples in harsh situations. MAX31865 RTD Amplifier: This specialized amplifier is designed to read the low resistance of PT1000 RTDs, resulting in optimal signal processing and error minimization. 3-Wire Compatibility: The breakout board offers 3-wire RTD connection combinations to meet your individual setup needs. excellent Accuracy Temperature Sensor: Temperature measurement with little drift and excellent resolution, ideal for applications requiring accuracy. MAX31865 SPI Interface: The breakout board seamlessly integrates with popular microcontrollers such as Arduino and Raspberry Pi, allowing for easy data collecting and control. PT1000 RTD Amplifier Calibration: The MAX31865 RTD amplifier has calibration capabilities, ensuring consistent and accurate readings throughout time. MAX31865 Fault Detection: Built-in fault detection procedures aid in the identification of issues such as sensor disconnections or over-temperature conditions, hence improving system reliability. Versatile Applications: Suitable for thermal cycling, industrial process control, laboratory investigations, and any scenario requiring precise temperature measurement. The 7Semi PT1000 RTD 3-Wire Temperature Sensor Amplifier Breakout Board - MAX31865 can help you optimize your temperature sensing capabilities. Elevate your projects with unrivaled precision and dependability.