74169 IC The 74169 is a digital logic IC that belongs to the 74xx series of integrated circuits. It is a 4-bit binary counter with a synchronous reset, meaning that the counter can be reset to zero at any time using a reset signal. The 74169 has four output lines, one for each bit in the counter, and it increments the count by one each time it receives a pulse on its clock input. It is commonly used in applications where a counter is needed, such as in timing circuits and frequency dividers. check out : 7448 IC Applications: Timing circuits Frequency dividers Pulse generation Digital clocks Automation systems Data acquisition systems check out : CD4028 - BCD to Decimal Decoder IC

7448 IC The 7448 is a digital logic IC that belongs to the 74xx series of integrated circuits. It is a BCD-to-7-segment decoder, which means that it can convert a binary-coded decimal (BCD) input into a pattern of signals that can be used to drive a 7-segment display. The 7448 has four BCD inputs and seven output lines, one for each segment of the 7-segment display. It also has an active-low output line for a decimal point. The 7448 is widely used in applications where a 7-segment display is used to display numerical information. check out : 74169 IC Applications: Digital clocks Digital thermometers Counters Process control displays Data acquisition systems Digital voltmeters

Hex Schmitt Trigger Inverter IC - 74HC14 The 74HC14 is a hex Schmitt trigger inverter integrated circuit (IC) with six independent Schmitt trigger inputs. Each input has an active high and active low output. The 74HC Series 74HC14 contains six independent gates each of which performs the logic INVERT function. Each input has hysteresis which increases the noise immunity and transforms a slowly changing input signal to a fast-changing, jitter-free output. Pinout : Pinout Of 74HC14 IC

74HC165 - 8-Bit Parallel In/Serial Out Shift Register IC The 74HC Series 74HC165 high-speed PARALLEL-IN/SERIAL-OUT SHIFT REGISTER utilizes advanced silicon-gate CMOS technology. It has the low power consumption and high noise immunity of standard CMOS integrated circuits, along with the ability to drive 10 LS-TTL loads. This 8-bit serial shift register shifts data from QA to QH when clocked. Parallel inputs to each stage are enabled by a low level at the SHIFT/LOAD input. Also included is a gated CLOCK input and a complementary output from the eighth bit. Clocking is accomplished through a 2-input NOR gate permitting one input to be used as a CLOCK INHIBIT function. Holding either of the CLOCK inputs high inhibits clocking, and holding either CLOCK input low with the SHIFT/LOAD input high enables the other CLOCK input. Data transfer occurs on the positive-going edge of the clock. Parallel loading is inhibited as long as the SHIFT/LOAD input is HIGH. When taken LOW, data at the parallel inputs are loaded directly into the register independent of the state of the clock. The 74HC logic family is functionally as well as pin-out compatible with the standard 74LS logic family. All inputs are protected from damage due to static discharge by internal diode clamps to VCC and the ground. check out : 4-bit Parallel-Access Shift Register IC - 74HC95 Pinout: Pinout Of 74HC165

Octal D-Type Latch 3-State Output IC - 74HC373 The 74HC Series 74HC373 high-speed octal D-type latches utilize advanced silicon-gate CMOS technology. They possess the high noise immunity and low power consumption of standard CMOS integrated circuits, as well as the ability to drive 15 LS-TTL loads. Due to the large output drive capability and the 3-STATE feature, these devices are ideally suited for interfacing with bus lines in a bus-organized system. When the LATCH ENABLE input is HIGH, the Q outputs will follow the D inputs. When the LATCH ENABLE goes LOW, data at the D inputs will be retained at the outputs until LATCH ENABLE returns HIGH again. When a high logic level is applied to the OUTPUT CONTROL input, all outputs go to a high impedance state, regardless of what signals are present at the other inputs and the state of the storage elements. The 74HC logic family is speed, function, and pin-out compatible with the standard 74LS logic family. All inputs are protected from damage due to static discharge by internal diode clamps to VCC and the ground. Pinout: Pinout Of 74HC373 IC

Octal D-Type Transparent Latch IC - 74HC573 The 74HC Series 74HC573 IC high-speed octal D-type latches utilize advanced silicon-gate P-well CMOS technology. They possess the high noise immunity and low power consumption of standard CMOS integrated circuits, as well as the ability to drive 15 LS-TTL loads. Due to the large output drive capability and the 3-STATE feature, these devices are ideally suited for interfacing with bus lines in a bus organized system. When the LATCH ENABLE(LE) input is HIGH, the Q outputs will follow the D inputs. When the LATCH ENABLE goes LOW, data at the D inputs will be retained at the outputs until LATCH ENABLE returns HIGH again. When a HIGH logic level is applied to the OUTPUT CONTROL OC input, all outputs go to a HIGH impedance state, regardless of what signals are present at the other inputs and the state of the storage elements. The 74HC logic family is speed, function, and pinout compatible with the standard 74LS logic family. All inputs are protected from damage due to static discharge by internal diode clamps to VCC and the ground. Pinout: Pinout Of 74HC573 IC

74HC00 - Quad 2-Input NAND Gate IC The 74HC Series 74HC00 IC is a 14-Pin Quad 2-Input NAND Gate IC. This device contains four independent gates each of which performs the logic NAND function. NAND gates utilize advanced silicon-gate CMOS technology to achieve operating speeds similar to LS-TTL gates with the low power consumption of standard CMOS integrated circuits. All gates have buffered outputs. All devices have high noise immunity and the ability to drive 10 LS-TTL loads. The 74HC logic family is functionally as well as pin-out compatible with the standard 74LS logic family. All inputs are protected from damage due to static discharge by internal diode clamps to VCC and the ground. Pinout: Pinout Of 74HC00 IC Input Pins 1, 2, 4, 5, 9, 10, 12, 13 Output Pins 3, 6, 8, 11 Power Supply (VCC) 14 Ground (GND) 7 Applications: AV Receivers Portable Audio Docks Blu-ray Players and Home Theater MP3 Players or Recorders Personal Digital Assistants (PDAs) Power: Telecom or Server AC/DC Supply (Single Controller: Analog and Digital) Solid State Drives (SSDs): Client and Enterprise TVs: LCD, Digital, and High-Definition (HDTV) Tablets: Enterprise Video Analytics: Server Wireless Headsets, Keyboards, and Mice

74HC02 - Quad 2-Input NOR Gate IC The 74HC Series 74HC02 IC is a 14-Pin Quad 2-Input NOR Gate IC. NOR gates utilize advanced silicon-gate CMOS technology to achieve operating speeds similar to LS-TTL gates with the low power consumption of standard CMOS integrated circuits. All gates have buffered outputs, providing high noise immunity and the ability to drive 10 LS-TTL loads. The 74HC logic family is functionally as well as pin-out compatible with the standard 74LS logic family. All inputs are protected from damage due to static discharge by internal diode clamps to VCC and the ground. Pinout: Pinout Of 74HC02 IC Also check 74LS12 NAND Gate IC (Pack of 5) . Which is used for logical decision making and circuits involving conditional operations.

74HC11 - Triple 3-Input AND Gate IC The 74HC11 is a digital integrated circuit (IC) with three separate 3-input AND gates. It belongs to the 74HC family of integrated circuits, which are high-speed CMOS (Complementary Metal-Oxide-Semiconductor) devices with quick switching rates and low power consumption. The 74HC Series 74HC11 has three inputs and one output for each AND gate. Only if all of the inputs are high is the output (logic 1) high (logic 1). The output is low if any of the inputs is low (logic 0). (logic 0). As a result, the 74HC11 can be used to create logic functions that require the combination of many signals. The 74HC11 comes in a typical DIP (Dual In-line Package) form factor and is easily incorporated into circuits utilising through-hole technology. It can handle input and output voltages ranging from 0V to Vcc and operates across a wide voltage range of 2V to 6V. Pinout: Pinout Of 74HC11 IC

Quad 2-Input Schmitt Trigger IC - 74HC132 The 74HC Series 74HC132 is a quad 2-input Schmitt trigger integrated circuit that is commonly used for signal conditioning and noise filtering. The Schmitt trigger input ensures that the IC's output switches cleanly and reliably in response to changes in the input signal. The 74HC132 contains four independent gates each of which performs the logic NAND function. Each input has hysteresis which increases the noise immunity and transforms a slowly changing input signal to a fast-changing, jitter-free output. Pinout: Pinout Of 74HC132 IC