Original DJI NAZA M V2 Flight Controller With GPS & PMU V2 for Multirotor Quadcopter DJI Naza-M V2 Multi-Rotor Flight Controller With GPS Module Supports nine multi-rotor configurations, the DJI NAZA-M V2 Drone Controller With GPS acts as the brains of the aircraft, managing pilot input and interpreting data from the various sensors, helping maintain a stable flying condition. There are four components to the system. Following are the capabilities inbuilt in this DJI Naza-M V2 Controller. 9 Types Multirotor Configurations Supported The Naza-M V2 is a powerful flight controller for enthusiast, commercial and industrial flyers. It’s easy to install, simple to configure and above all, extremely stable. Nine types of traditional motor mixes are supported, making it ideal for every setup. Free Ground Station Support 16 point Ground Station is available free for both iPad and PC, without serial number verification. 2.4G Bluetooth Datalink required. Advanced Attitude Stabilization Algorithms The Naza-M V2 boasts the extraordinary stability you would expect of all DJI flight control systems and combines it with unparalleled maneuverability with and without GPS. Built into it are automatic GPS course correction plus GPS and compass interference monitoring, which combine to offer more stable flight and minimal magnetic interference. Takeoff Assistance Drift-free, stable take offs on different surfaces is ensured with Takeoff Assistance. Intelligent Orientation Control (IOC) Forward on a multirotor is normally the direction the nose is facing, which can get confusing when turning, but with IOC switched on, direction is hugely simplified. In Course Lock mode, forward is the same as the nose direction recorded on takeoff. In Home Lock mode, forward is the direction from the Quadcopter's current position back to home. Motor Failure Protection If a hexrotor or octorotor equipped with a Naza-M V2 suffers a motor failure in flight in attitude or GPS mode, it will maintain its altitude and rotate around the stopped motor. This allows it to fly safely back to home and land. Failsafe And Auto Go Home Support If the connection between the multirotor and the remote control are disconnected during flight, a failsafe system will activate. Provided there was enough GPS signal at the time of the disconnection, the multirotor will fly back to its point of takeoff and land automatically. This feature can also be triggered manually using the One-Key Go-Home function activated using Assistant. Assistant for Smartphone Using a BTU with power efficient Bluetooth, parameters can be adjusted at any time through a smartphone without excessive power use. Connection records are automatically stored by the Bluetooth module and protected by password. Parameters can be automatically synchronized to the cloud restored immediately when mobile devices are changed. These features makes the DJI Naza-M V2 very versatile and best controller for drones. Built-In Functions: Multiple Autopilot Control Mode Enhanced Fail-safe Low Voltage Protection S-Bus Receiver Support PPM Receiver Support Independent PMU Module 2-axle Gimbal Support

Dronacharya Vikas R&D DIY RC Drone Kit for Engineering Students and Researchers The Dronacharya Vikas R&D DIY RC Drone Kit is a comprehensive and versatile drone assembly kit designed to empower students, educators, and innovators in exploring UAV technology. Whether you are working on academic projects, developing prototypes, or researching autonomous systems, this DIY drone kit offers an immersive hands-on experience in drone integration, control mechanisms, and sensor applications. As a complete RC drone kit, it enables users to gain practical knowledge while fostering innovation in aerial robotics and research-based applications. Seamless integration & Open Source Suitable for smooth physical and logical integration of add-ons and payloads. (SRS) Steady, Robust, Safe Suitable for novice pilots and expert R&D projects. Swift & Easy, Assembly & Maintenance A well-designed drone decreases complexity across its entire lifecycle, from setup to operation. Features: Pixhawk-based Flight Controller for accurate navigation and autonomous control Supports the UART, I2C, and MAVLink protocols for smooth communication. ROS 2 and Simulation Software Suitable for cutting-edge autonomy research. Sensor Integration: Ultrasonic, LiDAR, GPS, IMU Ground Control Software: Supports Mission Planner and QGroundControl (QGCS). Modular design with customizable payloads and drone configurations. Introducing Dronacharya Vikas R&D DIY RC Drone Kit Applications: Engineering students and researchers. UAV development and autonomous system testing. STEM Education and Drone-Based Learning Environments This Kit Includes: 1 x Flight Controller: Radiolink MiniPix A compact and cost-effective flight controller based on the Pixhawk architecture, ideal for research and educational drones. Technical Specifications: Processor: STM32F427 32-bit ARM Cortex M4 core with FPU IMU: MPU6500 accelerometer/gyroscope Barometer: MS5611 Magnetometer: External required (GPS unit supports this) Input Voltage: 4.8V – 5.5V Communication Interfaces: 1 x UART (telemetry), 1 x USB, I2C, PPM, SBUS, PWM output Firmware: Supports PX4 and ArduPilot Weight: ~15g Form Factor: Compact and lightweight, ideal for small drones 1 x GPS Module: Radiolink TS100 High-performance GNSS module with integrated compass for accurate global positioning and navigation.. Technical Specifications: GNSS Systems: GPS, GLONASS, Beidou Positioning Accuracy: ±2.5 meters (horizontal) Refresh Rate: 10 Hz Compass: Built-in digital compass (HMC5883L) Communication: UART and I2C Operating Voltage: 5V DC Antenna: Ceramic active antenna LED Indicator: Satellite fix status Weight: ~20g Mounting: Includes anti-vibration mount and cable 4 x Brushless Motors: 920KV 2212 (2 CW + 2 CCW) KV Rating: 920KV Configuration: 14 Poles / 12 Slots Max Current: ~15-18A Mounting Hole Distance: 16mm x 19mm Propeller Compatibility: 8”–10” props Shaft Diameter: 3.17mm Weight: ~55g each 4 x Electronic Speed Controllers: Hobbyking 20A ESC (Custom Vikas Connectors) Max Current: 20A continuous, 25A burst (10s) BEC Output: 5V / 2A Linear Firmware: Custom firmware compatible with SimonK/BLHeli Connector: Proprietary Vikas plug-in system for easy swaps 4 x Motor Mounts (Molded Plastic Shells) Custom-designed heavy-duty motor mounts made from durable molded plastic Withstand vibration and mechanical stress Allow for fast, tool-less replacements 8 x Arm Bases (Custom Vikas Shell) Precision-molded hard plastic that securely holds the frame together Designed to fit modular carbon arms and ensure easy maintenance 4 x Carbon Fiber Arms (Custom-Made for Vikas) Lightweight yet highly rigid Designed for modular swapping and high endurance Mounting compatible with Vikas motor mounts and bases 4 x Carbon Fiber Landing Poles Shock-absorbing landing gear Carbon fiber structure ensures durability during repeated takeoffs/landings 1 x Top Plate (Universal Integration Platform) Designed for wide compatibility with various drone components Supports multiple battery sizes and payloads CNC-cut for precision and flexibility in mounting 1 x Bottom PCB (Proprietary R&D Enabler) Designed specifically for R&D and prototyping Integrated voltage rails: 5V, 3.3V, and 12V outputs Power distribution for ESCs, sensors, onboard computers (Raspberry Pi, Jetson Nano, etc.) Solder pads and headers for custom circuit integration 1 x 2200 mAh Li-Po Battery Voltage: 11.1V (3S) Capacity: 2200 mAh Discharge Rate: 25C – 35C Connector: XT60 1 x Li-Po Balance Charger Supports 2S–3S Li-Po batteries LED indicators for cell balance and charging completion Over-voltage and over-current protection 1 x Set of Consumables Zip ties, double-sided tape, Velcro straps For cable management and secure mounting 1 x Fasteners Kit for Vikas Screws, bolts, and nuts compatible with all parts of the Vikas drone Stainless steel and anodized aluminum mix 1 x 2.5mm Allen Key Provided for assembly and maintenance 1 x Set of Silicon Landing Caps Soft end caps for landing poles Reduces vibration and wear during landings 1 x Propeller Set (CW & CCW) 2 x Clockwise and 2 x Counterclockwise Balanced for smooth flight and efficient thrust

EMAX D-SHOT Bullet 6A ESC for Onshot42 2S FPV Racing Drone The EMAX D-SHOT Bullet 6A ESC is a high-performance drone speed controller engineered for Onshot42 2S FPV racing drones. Designed with precision, this compact ESC controller delivers reliable performance with a 6A continuous current capacity and advanced DShot protocol support for ultra-smooth throttle control. Featuring BLHeli-S firmware, it includes active braking, damped light output, and programmable motor timing—ensuring fast response, enhanced flight stability, and improved efficiency. Perfect for drone enthusiasts seeking a lightweight yet powerful electronic speed controller for drone builds. Features: The market's lightest and smallest ESC, built particularly for high-level FPV racing. Using the most recent BLHeli-S firmware (16.5), hardware PWM provides a signal that improves smooth throttle response and reduces noise. Supports the new digital signal DSHOT as well as the analog signals MULTISHOT, ONESHOT42, and ONESHOT125. High-quality MOSFET and ceramic capacitors. The 3oz high TG PCB board dramatically improves heat dissipation and system efficiency. The new aluminum heat sink provides protection from propeller impact damage.

EMAX Nano Series 20A BLHeli Oneshot125 3-4S Electronic Speed Controller The EMAX Nano Series 20A BLHeli Oneshot125 Electronic Speed Controller is a high-performance ESC controller built specifically for racing drones and multi-copters. Featuring BLHeli firmware and OneShot125 compatibility, this 20A ESC ensures ultra-fast throttle response and smooth flight performance. With a peak current of up to 40A, it delivers reliable power for demanding drone setups. Its opto design and twisted pair wire provide excellent noise resistance, while compatibility with popular flight controllers like Skyline32, Naze32, Pixhawk, and CC3D makes integration effortless. Crafted using premium electronic components, this electronic speed controller for drone offers outstanding durability, efficient current handling, and stable operation — making it the perfect choice for drone enthusiasts and FPV racers. Features: Use genuine electronic components to ensure good quality and extend the ESC's present durability capability. It is built on BLHeli firmware and is optimized for great performance, including outstanding linearity and a much faster throttle response. Multi-rotors are specifically intended to be compatible with fixed-wing aircraft and helicopters. Multiple protective measures are available, including low-voltage cut-off, overheat prevention, and throttle signal loss protection. The throttle range may be adjusted and is entirely compatible with all receivers, resulting in smooth, linear, and precise throttle responses. All parameters, including default settings, can be programmed with a program card or a transmitter.

EMAX Simon Series 20A 2-4S LiPo Brushless Electronic Speed Controller for Drones and RC Aircraft The EMAX Simon Series 20A Brushless Electronic Speed Controller is a high-quality ESC for drones and RC aircraft, designed to deliver smooth, responsive, and reliable performance. Powered by advanced SimonK firmware, this drone speed controller ensures superior throttle precision and flight stability. Compatible with 2–4S LiPo batteries, it supports a wide range of brushless motor configurations, making it ideal for FPV racing and aerial applications. With its compact, lightweight build and efficient power delivery, the EMAX Simon 20A electronic speed controller stands out as a dependable choice for hobbyists seeking performance and durability in every flight. Features: High quality components American-made (IR) MOSFETs provide consistent current and long-term durability. PCB is durable. To extend the life of the ESC, it is constructed with thick 5-oz. high-grade copper. Advanced Firmware. SimonK firmware improves throttle response and stability. Battery compatibility Supports 2-4S LiPo batteries for flexible power sources. Lightweight Design Compact and lightweight, excellent for drone enthusiasts looking for efficient and rapid motor control.

FlySky FS-CT6B 6ch 2.4GHz Transmitter & Receiver FlySky CT6B 2.4Ghz 6 Channel Transmitter with FS-R6B Receiver Remote is the popular 6 Channel Radio. This 6 Channel Transmitter and Receiver is an entry-level 2.4 GHz radio system offering the reliability of 2.4 GHz signal technology and a receiver with 6 channels. This is a value-for-money, entry-level transmitter. The FlySky FS-CT6B transmitter & receiver ideal for drones, quadcopters, and multicopters that require a 6-channel operation. This FlySky remote control has a very lightweight and handy design with two retract switches and proportional flap dials in easy reach for channels 5 and 6. This digital RC controller for hobby drones can be powered by 8 x AA Size Batteries or a 12V Power Supply. It comes with a trainer port to help beginners learn flying. This FlySky FS-CT6B radio controller comes with an FS-R6B receiver which is one of the best receivers we had in the class at a very reasonable cost. It can be configured by connecting it to the computer. Use the T6 config software to configure your radio on a computer. Check out : SKYDROID T12 2.4GHZ 12CH REMOTE CONTROL WITH CAMERA Features: This is High quality transmitter and receiver for drones and quadcopters 2.4 GHz signal technology Lightweight and handy design Retract switches and proportional flap dials for channels 5 and 6 Can be powered by 8 x AA Size Batteries or a 12V Power Supply Trainer port for beginners Comes with FS-R6B receiver Configurable via computer with T6 config software Integrated Contrast Adjustment, Throttle cut High quality and stability Low voltage warning LED DSC Port and Charger Port included Full range 2.4GHz radio High receiving sensitivity with very low power consumption Applications: Multirotors RC Planes RC Boats RC Helicopters Also check the Flysky FS-GT2 Transmitter with FS-GR3E Receiver , designed for RC cars, boats, planes, trucks, and quadcopters.

Flysky FS-i10 10CH 2.4GHz AFHDS 2 LCD Transmitter with Receiver The Flysky Fsi10 remote controller is a great transmitter-receiver for quadcopter and drones. The Flysky transmitter receiver has a great ergonomic design and fits right in the palm of your hands. It is integrated with FS-ATM01, FS-APD02, FS-AVT01, FS-APD01, FS-AEV01 module. The Flysky drone remote controller has hardware that features 8 switches & 5 knobs for optimal performance. It uses the FLYSKY 2.4GHz AFHDS 2 to achieve the role of modern two-way communications telemetry. Model type uses for Drones, helicopter, airplane, and glider. Features: Equipped with 10 channels for precise and flexible control of drones, helicopters, airplanes, and gliders. Operates on 2.4GHz AFHDS 2 technology, ensuring stable signal transmission and minimal interference. Includes 8 switches and 5 control knobs for highly customizable and responsive operation. Features a built-in LCD display for real-time data, telemetry, and easy configuration. Ergonomic design provides a comfortable grip, ideal for extended flying sessions. Integrated with FS-ATM01, FS-APD02, FS-AVT01, FS-APD01, and FS-AEV01 modules for enhanced connectivity and performance.

FlySky FS-i6 2.4GHz 6 Channel RC Transmitter The FlySky FS-i6 2.4GHz 6 Channel RC Transmitter is an excellent choice for both beginners and experienced hobbyists because of its blend of user-friendly features and robust performance. This FlySky transmitter utilizes the advanced AFHDS 2A protocol, which ensures secure, interference-free communication and low power consumption, which is especially beneficial during long flights. The design is ergonomic and lightweight (under 400g). It’s intuitive backlit LCD screen makes it comfortable to use and easy to program, even for new users. The FS-i6 is highly versatile, making it a preferred drone remote controller for a wide range of RC applications. It supports six channels, allowing precise control over drones, airplanes, helicopters, gliders, and even robotics. With 20 model memory slots, pilots can conveniently switch between different aircraft or vehicle profiles, making it an ideal RC transmitter for drones & planes used in both recreational and competitive settings. In terms of range, the Flysky FSi6 Remote Controller can typically control models up to 500 meters away. The transmitter operates on a maximum voltage of 6V, powered by four AA batteries, ensuring reliable operation and easy battery replacement. Overall, the FlySky FS-i6 offers a compelling mix of reliability, flexibility, and affordability, making it a go-to choice for anyone seeking a dependable RC transmitter for their aerial or ground-based models also check our drone transmitter and receiver collection, which offers a range of options with different features and price points. Features: Flysky FS-i6 RC Transmitter with FS-iA6B receiver 6-channel transmitter suitable for quadcopters, multi-rotors, RC helicopters, and aeroplanes Utilizes solid and reliable Automatic Frequency Hopping Digital System (AFHDS) spread spectrum technology FS-iA6B receiver with a range exceeding 500m and dual antennas for excellent reception and interference rejection Easy to use Programming & Navigation Buttons The backlit LCD screen displays real-time transmitter and receiver voltage levels, trim levels, and other information Ultra-slim case design ergonomically fits hands, reducing hand fatigue during long flights Digital trims, backlit LCD screen, and simple programming for a modern feel and ease of use Adjustable length sticks and loop for attaching neck strap for added comfort Features a 3-position switch and two adjustable knobs for changing flight modes or multiple flap position options Expands capabilities with optional telemetry receivers and a variety of sensors. Comparision Table: Feature FlySky FS-i6 FlySky FS-i6X Channels 6 6 (expandable to 10) Protocol AFHDS 2A AFHDS 2A, compatible with AFHDS RF Range 2.405–2.475 GHz 2.408–2.475 GHz Resolution 4096 4096 Power Supply 4 × AA Batteries 4 × AA Batteries Display 128 × 64 LCD 128 × 64 LCD Low Voltage Alarm Yes (< 4.2V) Yes (< 4.2V) USB Port Micro-USB (simulator support) Micro-USB (simulator + firmware upgrade) Receiver Compatibility FS-iA6 FS-iA6B, FS-iA10B, FS-X6B Expandable Channels No Yes (via firmware update)

FlySky FS-TH9X 2.4G 9CH Transmitter A transmitter is one of the most crucial parts while using a drone. Because it uses radio signals to communicate wirelessly with a Radio Receiver that is attached to an aircraft or multirotor that is being remotely controlled, you can't fly a multirotor without it. The flysky th9x range FS-TH9X 2.4GHz 9CH Upgrade Transmitter and FS-IA10B Receiver have completely changed how people experience RC, and they can now compete with the best products on the market. fs th9x  designed and domestically patented this Upgraded 9 channel with FS-RM003 2.4GHz Module TRANSMITTER'S AFHDS (automatic frequency hopping digital system) for all Radio Control model enthusiasts. The fs th9x system was specifically created for all radio control models because they have excellent active and passive anti-jamming capabilities, extremely low power requirements, and great receiver sensitivity. fs-th9x FLYSKY AFHDS is presently regarded as one of the top systems on the market after years of market research and extremely rigorous testing by engineers. The standard of the latest generation of radio systems flysky 9x is 2.4GHz because of its many benefits. By operating at 2.4 GHz, the radio control is kept out of the frequency range of any "noise" produced by the other electronic parts of your helicopters, such as the brushless motor, Electronic speed controller, Servos, and any metal-to-metal noise, which eliminates interference and glitching that can affect traditional frequency systems. FlySky is the brand name. FS-TH9X 2.4G 9CH Upgrade is the item name. 9 channels are available. Model types include cars, boats, helicopters, gliders, and quadcopters. 2.40 to 2.48GHz is the RF band. FlySky FS Transmitter works between 2.405 and 2.475GHz in frequency. Each radio system in this band uses 16 separate channels and 160 different types of hopping algorithms. This band has been broken into 142 independent channels. This radio system spans the entire frequency spectrum and has a high gain, high-quality multidirectional antenna. This radio system, when combined with a high sensitivity receiver, ensures jam-free long-distance radio communication. Each transmitter has a distinct ID, and when a transmitter and receiver are connected, the receiver stores the distinct ID and may only accept data from the distinct transmitter. By avoiding selecting a different transmitter signal, greatly improves safety and interference immunity. This radio system makes use of sensitive receiver chips and low-power electronic components. Even more, electricity is saved by the intermittent signal used in RF modulation. According to the needs of the customer, the AFHDS2A system's automated identification feature can convert the current mode automatically between one-way and two-way communication. How to bind the RX (receiver) to the TX (transmitter): Plug bind plug into BAT, turn on plane/heli, and the LED light should flash (make sure power is connected to RX via ESC) Hold down the bind button on the transmitter module while turning on the TX The light should go steady now Let go of the bind button, turn off plane/heli, remove the bind plug, and turn off TX Turn on TX and then turn on plane/heli

FS-TH9X 2.4GHz 9CH Upgrade Transmitter with FS-IA10B Receiver The FS-TH9X 2.4GHz 9CH Upgrade Transmitter with FS-IA10B Receiver has revolutionized the way people experience RC, and now this radio transmitter and Receiver can stand up to the top competition. When using a drone, a transmitter is one of the most important components. You can’t fly a multirotor without it because it uses radio signals to send commands wirelessly to a Radio Receiver, which is connected to an aircraft or multirotor that is being remotely controlled. This Upgraded 9 channel with FS-RM003 2.4GHz Module TRANSMITTER’S AFHDS (automatic frequency hopping digital system), is developed by FLYSKY for all the Radio Control model lovers and is patented by FLYSKY at home. The system is specially developed for all the Radio control models, that offer super active and passive anti-jamming capabilities, very low power consumption, and high receiver sensitivity. With extremely rigorous testing by engineers and studying the markets for years, FLYSKY AFHDS is now considered to be one of the best systems available in the market. 2.4GHz is the standard of the new generation radio system because it has a lot of advantages. Operating at 2.4 GHz puts the radio control out of the frequency range of any ‘noise’ generated by the other electronic components on your helicopters – such as the brushless motor, Electronic speed controller, Servos, and any metal-to-metal noise – eliminating interference and glitching that can affect traditional frequency system. How to bind the RX (receiver) to the TX (transmitter): Plug bind plug into BAT, turn on plane/heli, and the LED light should flash (make sure power is connected to RX via ESC) Hold down the bind button on the transmitter module while turning on the TX The light should go steady now Let go of the bind button, turn off plane/heli, remove the bind plug, and turn off TX Turn on TX and then turn on plane/heli