SmartElex USB to RS-485 Converter Module with FT232RL IC

Female to Female Jumper Wires (20cm) 40pcs These are 20cm 40pcs Female to Female Jumper wires, very Flexible and easily detachable. These jumper cables have 1Pin female to the 1pin female header with both ends. Also, it is compatible with 2.54 mm mil spacing pin headers. This cable is an electrical wire or group of them in a cable with a connector or pins at each end, which is normally for interconnecting the components of a breadboard or other prototype or test circuit, internally or with other equipment or components, without soldering. Individual Dupont Cables are fitted by inserting their end connectors into the slots provided in a breadboard, the header connector of a circuit board, or a piece of test equipment. Mostly Dupont cables are useful with Orange Pi, Banana Pi, Raspberry Pi , Arduino , and other mini PCs and development boards . It is very useful in the PCB project, PC motherboard, as well as Breadboard connections. Additionally, these jumper wires allows you to plug and unplug easily for prototyping and can be used over and over again. Check out the best selection of Jumper Wires . Applications: Raspberry Pi Arduino PCB projects Breadboard connections Get a complete set of M2M, M2F, F2F Jumper Wires Set for DIY projects.

A3967 Stepper Motor Driver This A3967 Stepper Motor Driver For Arduino is the most recent version of EasyDriver v44, which was created in collaboration with Brian Schmalz. When compared to previous versions, it offers more flexibility and control over your stepper motor . It is a simple stepper motor driver that is compatible with most microcontrollers and capable of producing a digital 0 to 5V pulse (0 to 3.3V pulse if you solder SJ2 closed on the EasyDriver). A 7V to 30V power supply is required for the module's motor. The digital interface is powered by an onboard voltage regulator that can be set to 5V or 3.3V. The A3967 is a full-featured microstepping motor driver with an integrated transistor. It is intended for use with bipolar stepper motors in full-, half-, quarter-, and eighth-step modes, with output drive capabilities of 30 V and 750 mA. The A3967 comes with a fixed off-time current regulator that can operate in slow, fast, or mixed current-decay modes. This current-decay control scheme produces less audible motor noise, higher step accuracy, and lower power dissipation. The transistor is essential to the A3967's simple implementation. Simply sending one pulse to the STEP input causes the motor to move one step (full, half, quarter, or eighth depending on two logic inputs). It is not necessary to programme phase-sequence tables, high-frequency control lines, or complex interfaces. The A3967 interface is ideal for applications where a complex P is either unavailable or overburdened. Features: A3967 microstepping driver Adjustable current control from 150mA/phase to 750mA/phase MS1 and MS2 pins are broken out to change microstepping resolution to full, half, quarter and eighth steps (defaults to eighth) Compatible with 4, 6, and 8-wire stepper motors of any voltage Breadboard-compatible pins.

CNC Shield for Arduino The CNC shield for Arduino has total four slots, can drive 4 A4988 stepper motors. Each road stepper motors only need two IO ports. In other words, six IO ports can be well managed three stepper motors. The CNC Shield V3.0 allows you to build a engraving machine, 3D printer, mini CNC and other similar devices using your Arduino. It is designed as a shield and can plug on top of an Arduino requiring no external connections and wiring. There are 4 slots on the board for plugging in stepper motor drive module which can drive 1 stepper motor each. Controlling each step stepper motor requires only two IO pins on the Arduino. Just insert this Arduino CNC Shield V3.0 onto an Arduino UNO , and install the GRBL firmware, you can then quickly build a DIY CNC engraving machine. This arduino shield is very convenient to use and is suitable for development boards compatible with Arduino. This CNC shield compatible with Arduino is the latest version of the CN shield model (V 3.0). The CNC Shield is GRBL 0.9 compatible and with the help of jumper wires , it is accessible to stepper drivers. Features: Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place. GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals) 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)

CNC Shield + UNO R3 Board compatible with Arduino + 4xDRV8825 Driver Kit Arduino Uno is an open-source microcontroller used by students and hobbyists entering the world of DIY electronics and automation, The Arduino Uno can be used for any application including being the brains of your next DIY 3D printer and/or CNC router The CNC Shield V3.0 allows you to build an engraving machine, 3D printer, mini CNC and other similar devices using your Arduino. It is designed as a shield and can plug on top of an Arduino requiring no external connections and wiring. Along with that, the CNC shield allows you to control up to four stepper motors by mounting on 4 stepper motor drivers, included with this kit The DRV8825 provides an integrated motor driver solution for printers, scanners, and other automated equipment. The device has two H-bridge and is intended to drive a bipolar stepper motor. Features: UNO R3 Board: The main microcontroller board compatible with Arduino. CNC Shield: An expansion board that allows for easy connection and control of stepper motors. 4x DRV8825 Stepper Motor Drivers: High-performance drivers for controlling stepper motors. Micro-Stepping: Supports micro-stepping settings for precise control of stepper motors. GRBL Compatibility: Compatible with GRBL firmware, which is widely used for CNC control. Voltage Range: Operates on 12-36V DC. Heat Sinks: Included for cooling the stepper motor drivers. USB Cable: For connecting the UNO R3 board to a computer. 40-Pin Row Needles: For additional connections. Applications: CNC Machines: Used for controlling stepper motors in CNC milling, engraving, and cutting machines. 3D Printers: Essential for driving stepper motors in 3D printers, ensuring precise layer deposition and movement. Laser Cutters: Controls stepper motors in laser cutting machines for accurate cutting and engraving. Robotics: Ideal for robotics projects requiring precise motor control, such as robotic arms and automated guided vehicles (AGVs). X-Y Tables: Used in X-Y tables for accurate positioning and movement in various industrial applications. Pick-and-Place Devices: Employed in pick-and-place machines for accurate component placement in electronics manufacturing. Labeling Machines: Used in labeling machines for precise label application. Pinout Diagram for the Arduino Uno Microcontroller Applications of the Kit The kit can be used to create custom 3D printers, scanner, CNC mills and other automated equipment applications

SmartElex ILD213T Opto-isolator Breakout Board SmartElex ILD213T Opto-isolator Breakout Board is designed to provide reliable electrical isolation between two circuits, helping protect sensitive components from voltage spikes, noise, and ground loop issues. This opto isolator board uses the ILD213T optocoupler to safely transfer signals while keeping high-voltage and low-voltage sections separated. It is a practical solution for students, hobbyists, engineers, educators, and startups who need to interface microcontrollers with external hardware without risking damage to their development boards or sensors. This ILD213T optoisolator module is well-suited for robotics, IoT systems, industrial automation, and embedded prototyping where signal integrity and safety are important. It integrates easily with platforms like Arduino, Raspberry Pi, and ESP32, enabling secure communication with relays, motors, sensors, and noisy electrical equipment. By using this electrical isolation board, users can build more stable and durable projects, ensuring consistent performance and reduced troubleshooting due to interference or short circuits. Features: Provides electrical isolation between input and output circuits Based on the ILD213T optocoupler for reliable signal transfer Protects microcontrollers from voltage spikes and noise Helps prevent ground loops and interference issues Compatible with Arduino, Raspberry Pi, ESP32, and similar boards Ideal for robotics, IoT, automation, and industrial interfaces

SmartElex TPS61040 12V Boost Converter Module SmartElex TPS61040 12V Boost Converter Module is designed to step up lower DC voltages to a stable 12V output, making it an ideal solution when your circuit requires a higher operating voltage than the available power source. This 12V boost converter is especially useful for students, hobbyists, engineers, educators, and startups working with battery-powered electronics or low-voltage microcontroller projects. It solves the challenge of powering 12V devices from compact power supplies like 3V or 5V inputs, without needing bulky transformer-based solutions. As a 3V to 12V boost converter, it integrates easily with platforms like Arduino, Raspberry Pi, ESP32, and other development boards, making it highly suitable for robotics, IoT nodes, portable gadgets, automation circuits, and prototyping environments. Its compact design and reliable output make it a practical choice for powering sensors, actuators, communication modules, and small peripherals that need a 12V line. This module helps builders maintain efficiency and portability in their designs while ensuring stable performance across a range of real-world applications. Features: Steps up lower DC input to a stable 12V output Based on the TPS61040 high-efficiency boost converter IC Enables 12V operation from 3V, 5V, or other low-voltage sources Ideal for battery-powered and portable electronics Compatible with Arduino, Raspberry Pi, ESP32, and similar boards Suitable for sensors, small modules, IoT devices, and automation projects

Cytron UNO Special Edition – Arduino-Compatible Board with Side Connectors The Cytron UNO Special Edition (CT-UNO-SE) is a fully Arduino-compatible development board designed for makers, students, and hobbyists who need reliable performance for DIY electronics and robotics projects. Built around the ATmega328P microcontroller, this board offers the familiar Arduino UNO experience while adding enhanced stability with the FTDI FT231X USB-to-Serial chip, ensuring smoother programming and communication. Whether you're prototyping sensors, robotics circuits, or automation systems, this board delivers a dependable and beginner-friendly platform for all your microcontroller learning needs. What makes the CT-UNO-SE stand out is its unique side connectors, allowing it to be stacked on top of or beneath Arduino shields, giving you maximum flexibility while building layered circuits or compact embedded systems. With full Arduino UNO R3 shield compatibility, 14 digital I/O pins, 6 analog inputs, and both 5V and 3.3V regulated outputs, this special edition board combines convenience, versatility, and long-term durability - all wrapped into a sleek white PCB that makes your projects look clean and professional. Features Built with the ATmega328P microcontroller paired with the Optiboot bootloader for faster program uploads. Equipped with the FTDI FT231X USB interface, offering stable and reliable serial communication. Supports a wide DC input range of 7–15V, suitable for most maker power setups. Includes a 1A 5V regulator and 500mA 3.3V regulator for powering sensors and modules. Offers 14 digital I/O pins (6 PWM) and 6 analog inputs for versatile interfacing. Fully R3 shield compatible with special side connectors for flexible stacking. Features 32KB Flash memory, 2KB SRAM, and 1KB EEPROM for program storage. Comes with easily visible TX, RX, power, and pin-13 LEDs placed on the board edge. Utilizes a durable USB Micro-B connector on a clean white PCB. Dimensions

Cytron UNO – Arduino UNO Compatible Board with USB Micro-B The Cytron UNO is a fully Arduino UNO compatible development board built with the reliable ATmega328P microcontroller, making it ideal for beginners, students, hobbyists, and electronics enthusiasts. Designed to offer the same functionality as the Arduino UNO R3, the Cytron UNO includes 14 digital I/O pins, 6 PWM outputs, 6 analog inputs, UART, SPI, I2C, and full R3 shield compatibility. With USB Micro-B connectivity, you can easily program the board using the same cable used for Android phones and power banks - making it more convenient and cost-friendly for modern makers. Cytron further enhances the board with a stronger onboard voltage regulator, improved power handling, and repositioned LEDs on the edge for better visibility, even when a shield is attached. The CT-UNO also includes extra standard pads for custom shields, an FTDI-based USB interface for stable programming, and robust DC input support from 7V to 15V. Whether you’re building IoT prototypes, robotics, embedded systems, or learning coding fundamentals, the Cytron UNO delivers reliability, ease of use, and full compatibility with the entire Arduino ecosystem. Features Powered by SMD ATmega328P with Optiboot (UNO R3) bootloader for fast programming. USB programming enabled by stable FTDI FT231X chip for improved reliability. Supports DC 7–15V input with upgraded onboard voltage regulator for higher output current. Offers 14 digital I/O pins, including 6 PWM outputs, and 6 analog inputs for versatile projects. Fully Arduino UNO R3 shield compatible with ISP header and broken-out SDA, SCL, IOREF pins. Uses USB Micro-B socket, compatible with standard Android phone cables. LEDs relocated to board edge for clear visibility during development. Includes additional 2.54mm pads for creating custom shields. White PCB design with clean layout and Cytron build quality. Dimensions

Cytron Maker UNO Plus – Arduino-Compatible Educational Board The Cytron Maker UNO Plus is a beginner-friendly, Arduino-compatible development board designed to simplify electronics and coding for students, educators, and STEM hobbyists. With onboard LEDs, a built-in piezo buzzer, a programmable pushbutton, and upgraded components, this board removes wiring complexity allowing learners to focus on coding, debugging, and hands-on exploration. Whether used for school projects, robotics, or microcontroller education, the Cytron Maker UNO Plus ensures a smooth and frustration-free learning experience. Thanks to its pre-labeled pin headers, Micro USB connectivity, and fully Arduino-compatible architecture, setup becomes effortless for new users. Students can instantly code and visualize real-time pin activity through indicator LEDs, making debugging easier and more intuitive. The Cytron Maker UNO Plus is ideal for classroom teaching, STEM labs, maker workshops, and hobby projects, helping learners jump straight into creating fun electronics projects like light sequences, melodies, and interactive displays. Features: Fully compatible with Arduino ecosystem, sharing all libraries and example codes. Integrated 12× onboard LEDs for simplified debugging and visual learning. Built-in piezo buzzer and programmable pushbutton for interactive projects without extra wiring. Upgraded 3.3V line provides 500mA output to support more sensors and modules. Micro USB interface replaces bulky USB Type-B for universal connectivity. Uses FT231X USB-to-Serial converter for easier and more reliable driver installation. Includes pin-header label stickers for effortless classroom identification. CE, FCC & RoHS compliant - safe, environmentally friendly, and education-ready. Students can write their names directly on the board to avoid mix-ups.

Cytron Maker Pi RP2040 – Robotics Controller Board with Raspberry Pi The Cytron Maker Pi RP2040 is a compact, beginner-friendly robotics controller board powered by the Raspberry Pi RP2040 microcontroller. Designed for DIY robotics, automation, and motion-control projects, this board integrates a dual-channel DC motor driver, four servo ports, and seven Grove connectors - giving makers everything they need to build robots without complex wiring. With compatibility across CircuitPython, MicroPython, C/C++, and even the Arduino ecosystem, this board ranks among the best RP2040 robotics controllers for students, hobbyists, and educators. Built for convenience, the Maker Pi RP2040 supports multiple power input options (USB, LiPo battery, or VIN), includes onboard functional test buttons, and features status LEDs for easy debugging. The preloaded demo code lets you start controlling motors, playing melodies, and testing GPIOs right out of the box. Whether you are exploring Raspberry Pi’s RP2040 ecosystem or building an advanced robot, the Cytron Maker Pi RP2040 robot controller offers exceptional versatility, ease of use, and reliable motor-driving performance. Features: Powered by the Raspberry Pi RP2040 dual-core Arm Cortex-M0+ processor. Includes dual-channel DC motor driver and four servo motor ports for robotics. Seven Grove ports support digital, analog, I2C, SPI, and UART expansion. Preloaded with CircuitPython for easy plug-and-play coding. Supports USB 5V, LiPo 1-cell battery, or 3.6–6V VIN input with automatic switching. Built-in LiPo charging circuit with safety protections. Onboard piezo buzzer, RGB LEDs, GPIO test LEDs, and push buttons. Quick-test buttons and motor output LEDs for immediate motor testing. Fully compatible with the Raspberry Pi Pico ecosystem, MicroPython, C/C++, and Arduino cores. Includes LEGO-compatible mounting holes and M3 mounting points. Board Layout: Dimension:

SmartElex RJ45 magjack Connector Breakout Board The SmartElex RJ45 MagJack Connector Breakout Board is a convenient module designed to make Ethernet connectivity accessible for custom electronics projects. It breaks out an RJ45 Ethernet jack with integrated magnetics, allowing users to interface network signals with development boards, prototypes, and embedded circuits without needing to design their own connector layout. This board is ideal for students, makers, engineers, educators, and startups who want to experiment with wired networking, communication protocols, or LAN-based control in robotics and IoT applications. This RJ45 MagJack breakout board is commonly used in IoT networks, automation systems, communication modules, and hardware prototypes that require Ethernet access for data transfer or device control. It can be used with platforms like Arduino, Raspberry Pi, ESP32, and other microcontroller boards that support Ethernet interfacing through additional hardware or modules. With reliable connectivity and a beginner-friendly breakout design, the SmartElex RJ45 MagJack Connector Breakout Board is a practical choice for testing, learning, and developing Ethernet-enabled electronic devices and embedded systems. Features: Breaks out an RJ45 MagJack Ethernet connector to easy-to-use pins Simplifies Ethernet interfacing for prototyping and custom circuits Integrated magnetics for stable network signal handling Compatible with Arduino, Raspberry Pi, ESP32 (with Ethernet support) Ideal for IoT, automation, LAN communication, and embedded systems Great for testing, learning, and building Ethernet-enabled devices

SmartElex USB-C Serial Basic Converter and CH340C IC Breakout Module he SmartElex USB-C Serial Basic Converter with CH340C is a compact USB-to-serial adapter designed to help users program, debug, and communicate with microcontroller boards and embedded systems. It converts USB signals to reliable UART serial communication, making it useful for students, hobbyists, engineers, educators, and startups working with boards that lack native USB support. With its USB-C interface and CH340C chipset, it provides a simple plug-and-play experience for connecting development boards, sensors, and custom circuits to a computer. This USB-to-serial converter is ideal for prototyping in robotics, IoT development, firmware flashing, serial monitoring, and automation projects. It works smoothly with platforms like Arduino, ESP8266, ESP32, Raspberry Pi (UART pins), and other TTL-based microcontrollers, making integration straightforward in both development and testing stages. Offering stable communication and easy computer connectivity, the SmartElex USB-C Serial Basic Converter with CH340C is a practical tool for labs, DIY electronics, and professional development environments. Features: Converts USB-C to TTL serial for programming and debugging CH340C chipset ensures stable and reliable UART communication Plug-and-play design for quick connection to development boards Compatible with Arduino, ESP8266, ESP32, Raspberry Pi (UART), and more Ideal for firmware flashing, serial monitoring, and IoT prototyping Compact breakout module for labs, workshops, and field testing

7Semi MCP23017 I2C to 16 IO Expander Breakout Board The 7Semi MCP23017 I2C to 16 IO Expander Breakout Board is designed to expand the digital I/O capability of microcontrollers using the trusted MCP23017 I2C IO Expander IC. It provides exactly 16 configurable GPIO pins over a single I2C bus, reducing wiring complexity while maintaining stable performance. Each pin can be independently set as input or output, and the onboard interrupt feature allows the controller to respond instantly to pin state changes. This MCP23017 Breakout Board is compact, easy to integrate, and ideal for applications such as home automation, robotics, industrial control panels, and any project that requires multiple digital inputs and outputs without consuming extra microcontroller pins. Features: 16 I/O Pins: Converts two signal pins into sixteen completely customizable I/O pins. Multi-board Expansion: For larger applications, stack up to 8 boards to provide up to 128 I/O pins. Configure I2C addresses by setting the A0, A1, and A2 jumpers. Dual Connectivity: Includes PH2.0 terminal and solder pad choices for simple connection. Wide Compatibility: Compatible with both 3.3V and 5V systems, ensuring platform versatility. Interrupt Support: The INTA and INTB interrupt pins are used for real-time signal handling. Development Resources: Includes detailed instructions and sample projects for Raspberry Pi, Arduino, STM32, and micro. Easy Integration: The I2C interface, combined with a 4Pin 2.0 mm JST connector, provides for an easy and flexible connection to any MCU.

SmartElex PAM8403 5V Two-Channel Stereo Mini Class-D Audio Amplifier The SmartElex PAM8403 5V Two-Channel Stereo Mini Class-D Audio Amplifier is a compact audio amplification module designed to deliver clear and efficient stereo sound from low-power audio sources. It solves the need for adding audio output to small electronic projects without bulky components or complex circuits. This module is suitable for students, makers, engineers, educators, and startups who want an easy way to integrate stereo audio into DIY electronics, learning kits, and embedded system prototypes. This stereo mini Class-D audio amplifier is commonly used in robotics, IoT devices, automation systems, and portable electronics that require lightweight and power-efficient audio output. It can be easily interfaced with platforms such as Arduino, Raspberry Pi, and ESP32 to drive small speakers in projects like voice alerts, sound feedback systems, and interactive devices. The simple design and stable performance make it easy to integrate into both prototype builds and finished products, enabling reliable audio output with minimal setup effort. Features: Two-channel stereo Class-D audio amplifier for clear sound output Operates on a 5V power supply, ideal for embedded projects High efficiency design with low heat generation Compact size suitable for space-constrained applications Drives small speakers for stereo audio output Compatible with Arduino, Raspberry Pi, ESP32, and other audio-enabled projects

SmartElex 8 Channel Multiplexer Breakout Module – (74HC4051) The SmartElex 8 Channel Multiplexer Breakout Module (74HC4051) is a compact and efficient solution for expanding input and output options in electronic projects. This 74HC4051 multiplexer breakout allows users to route multiple signals through a single microcontroller pin, solving the problem of limited I/O availability when working with sensors, switches, or analog inputs. It is designed for students, makers, engineers, educators, and startups who need a practical way to manage multiple device connections without increasing hardware complexity. This module acts as both an 8 channel multiplexer and demultiplexer, making it suitable for robotics, IoT systems, automation tasks, and rapid prototyping. It integrates smoothly with Arduino, Raspberry Pi, ESP32, and similar platforms, enabling users to scale projects without sacrificing performance or stability. Whether you are building sensor hubs, data acquisition systems, or experimenting with signal routing, this multiplexer demultiplexer module offers a reliable and easy-to-use interface that enhances flexibility in circuit design. Features: Based on the 74HC4051 8-channel analog/digital multiplexer IC Expands I/O by routing up to 8 signals through a single control interface Works as both a multiplexer and demultiplexer for flexible signal routing Helps manage limited microcontroller pins in multi-sensor projects Compatible with Arduino, Raspberry Pi, ESP32, and similar platforms Ideal for robotics, IoT systems, data acquisition, and prototyping