SmartElex ESP32 WROOM_C Development Board – WiFi & Bluetooth Microcontroller Module

Female to Female Jumper Wires (20cm) 40pcs These are 20cm 40pcs Female to Female Jumper wires, very Flexible and easily detachable. These jumper cables have 1Pin female to the 1pin female header with both ends. Also, it is compatible with 2.54 mm mil spacing pin headers. This cable is an electrical wire or group of them in a cable with a connector or pins at each end, which is normally for interconnecting the components of a breadboard or other prototype or test circuit, internally or with other equipment or components, without soldering. Individual Dupont Cables are fitted by inserting their end connectors into the slots provided in a breadboard, the header connector of a circuit board, or a piece of test equipment. Mostly Dupont cables are useful with Orange Pi, Banana Pi, Raspberry Pi , Arduino , and other mini PCs and development boards . It is very useful in the PCB project, PC motherboard, as well as Breadboard connections. Additionally, these jumper wires allows you to plug and unplug easily for prototyping and can be used over and over again. Check out the best selection of Jumper Wires . Applications: Raspberry Pi Arduino PCB projects Breadboard connections Get a complete set of M2M, M2F, F2F Jumper Wires Set for DIY projects.

A3967 Stepper Motor Driver This A3967 Stepper Motor Driver For Arduino is the most recent version of EasyDriver v44, which was created in collaboration with Brian Schmalz. When compared to previous versions, it offers more flexibility and control over your stepper motor . It is a simple stepper motor driver that is compatible with most microcontrollers and capable of producing a digital 0 to 5V pulse (0 to 3.3V pulse if you solder SJ2 closed on the EasyDriver). A 7V to 30V power supply is required for the module's motor. The digital interface is powered by an onboard voltage regulator that can be set to 5V or 3.3V. The A3967 is a full-featured microstepping motor driver with an integrated transistor. It is intended for use with bipolar stepper motors in full-, half-, quarter-, and eighth-step modes, with output drive capabilities of 30 V and 750 mA. The A3967 comes with a fixed off-time current regulator that can operate in slow, fast, or mixed current-decay modes. This current-decay control scheme produces less audible motor noise, higher step accuracy, and lower power dissipation. The transistor is essential to the A3967's simple implementation. Simply sending one pulse to the STEP input causes the motor to move one step (full, half, quarter, or eighth depending on two logic inputs). It is not necessary to programme phase-sequence tables, high-frequency control lines, or complex interfaces. The A3967 interface is ideal for applications where a complex P is either unavailable or overburdened. Features: A3967 microstepping driver Adjustable current control from 150mA/phase to 750mA/phase MS1 and MS2 pins are broken out to change microstepping resolution to full, half, quarter and eighth steps (defaults to eighth) Compatible with 4, 6, and 8-wire stepper motors of any voltage Breadboard-compatible pins.

CNC Shield for Arduino The CNC shield for Arduino has total four slots, can drive 4 A4988 stepper motors. Each road stepper motors only need two IO ports. In other words, six IO ports can be well managed three stepper motors. The CNC Shield V3.0 allows you to build a engraving machine, 3D printer, mini CNC and other similar devices using your Arduino. It is designed as a shield and can plug on top of an Arduino requiring no external connections and wiring. There are 4 slots on the board for plugging in stepper motor drive module which can drive 1 stepper motor each. Controlling each step stepper motor requires only two IO pins on the Arduino. Just insert this Arduino CNC Shield V3.0 onto an Arduino UNO , and install the GRBL firmware, you can then quickly build a DIY CNC engraving machine. This arduino shield is very convenient to use and is suitable for development boards compatible with Arduino. This CNC shield compatible with Arduino is the latest version of the CN shield model (V 3.0). The CNC Shield is GRBL 0.9 compatible and with the help of jumper wires , it is accessible to stepper drivers. Features: Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place. GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals) 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)

CNC Shield + UNO R3 Board compatible with Arduino + 4xDRV8825 Driver Kit Arduino Uno is an open-source microcontroller used by students and hobbyists entering the world of DIY electronics and automation, The Arduino Uno can be used for any application including being the brains of your next DIY 3D printer and/or CNC router The CNC Shield V3.0 allows you to build an engraving machine, 3D printer, mini CNC and other similar devices using your Arduino. It is designed as a shield and can plug on top of an Arduino requiring no external connections and wiring. Along with that, the CNC shield allows you to control up to four stepper motors by mounting on 4 stepper motor drivers, included with this kit The DRV8825 provides an integrated motor driver solution for printers, scanners, and other automated equipment. The device has two H-bridge and is intended to drive a bipolar stepper motor. Features: UNO R3 Board: The main microcontroller board compatible with Arduino. CNC Shield: An expansion board that allows for easy connection and control of stepper motors. 4x DRV8825 Stepper Motor Drivers: High-performance drivers for controlling stepper motors. Micro-Stepping: Supports micro-stepping settings for precise control of stepper motors. GRBL Compatibility: Compatible with GRBL firmware, which is widely used for CNC control. Voltage Range: Operates on 12-36V DC. Heat Sinks: Included for cooling the stepper motor drivers. USB Cable: For connecting the UNO R3 board to a computer. 40-Pin Row Needles: For additional connections. Applications: CNC Machines: Used for controlling stepper motors in CNC milling, engraving, and cutting machines. 3D Printers: Essential for driving stepper motors in 3D printers, ensuring precise layer deposition and movement. Laser Cutters: Controls stepper motors in laser cutting machines for accurate cutting and engraving. Robotics: Ideal for robotics projects requiring precise motor control, such as robotic arms and automated guided vehicles (AGVs). X-Y Tables: Used in X-Y tables for accurate positioning and movement in various industrial applications. Pick-and-Place Devices: Employed in pick-and-place machines for accurate component placement in electronics manufacturing. Labeling Machines: Used in labeling machines for precise label application. Pinout Diagram for the Arduino Uno Microcontroller Applications of the Kit The kit can be used to create custom 3D printers, scanner, CNC mills and other automated equipment applications

7Semi SHT40 Temperature & Humidity Sensor Breakout I2C Qwiic SHT40 Breakout (ES-13514) The 7Semi SHT40 Temperature & Humidity Sensor Breakout (I2C Qwiic) is a compact and reliable sensor module designed to measure both temperature and humidity with high accuracy. It is based on the Sensirion SHT40 sensor, making it suitable for modern electronics projects that need precise environmental data. This breakout board supports I2C communication and comes with a Qwiic connector, allowing quick and solder-free connections with microcontrollers like Arduino, ESP32, and Raspberry Pi. Its small size and low power consumption make it ideal for IoT devices, weather monitoring, indoor air quality projects, and learning applications where simplicity and accuracy matter. Features: High-accuracy temperature and humidity sensing using the SHT40 sensor Supports I²C communication for easy integration with microcontrollers Qwiic connector enables quick, solder-free plug-and-play connections Wide measurement range of 0–100% RH and –40°C to +125°C temperature Low-power and compact design, ideal for IoT and battery-powered projects Compatible with Arduino, Raspberry Pi, ESP32, and other development boards SHT40 Board Dimensions

SmartElex 10A 5V 1-Channel Relay Module The SmartElex 10A 5V 1-Channel Relay Module is a compact and dependable low level trigger relay module designed to control high-power devices using low-voltage microcontrollers. Operating at 5V DC, this single channel relay module features an SPDT relay rated for 10A at 250VAC, making it suitable for switching lights, motors, pumps, and other appliances. Its isolated input circuitry helps protect sensitive control boards from voltage spikes, while the onboard pull-down circuit prevents false triggering during startup. With a clear power indicator and secure mounting design, this 5V Relay Module delivers safe, stable, and long-lasting performance for home automation, industrial control, and DIY electronics projects. Features: A single-channel relay module with SPDT setup Supports up to 10A at 250 VAC for high-current applications. High-level trigger for dependable control. Compatible with a wide range of microcontrollers, including Arduino, AVR, PIC, and ARM. Isolated inputs to protect sensitive control circuitry. Contains a pull-down circuit to avoid inadvertent activation. Power supply indicator for rapid status checks. complies with international safety standards Convenient installation with four mounting holes.

ATMEGA328P SMD IC for Arduino Nano/UNO – AVR Microcontroller The ATMEGA328P SMD IC (ATMEGA328P-AU) is a high-performance 8-bit AVR microcontroller widely used in Arduino Nano and Arduino Uno boards. Designed with picoPower technology, this SMD version includes 32KB ISP Flash, 2KB SRAM, 1KB EEPROM, multiple timers, USART, SPI, and I2C support. Making it ideal for embedded electronics, DIY projects, automation systems, and IoT applications. Its compact SMD package makes it suitable for custom PCB designs and small-form-factor projects. This microcontroller is fully compatible with Arduino IDE, making programming easy using an AVR programmer or bootloader. With features like 23 GPIO pins, 6-channel 10-bit ADC, watchdog timer, and flexible power-saving modes, the ATMEGA328P SMD IC delivers powerful performance while maintaining low power consumption. Whether you're building a new Arduino-compatible board or repairing an existing one, this IC provides reliability, stability, and seamless integration. Features: ATMEGA328P-AU SMD AVR microcontroller used in Arduino Nano/UNO boards. Supports 32KB Flash memory with read-while-write capability, 1KB EEPROM, and 2KB SRAM. Fully compatible with Arduino IDE; can be programmed using an AVR programmer. Offers 23 GPIO pins, 3 timers/counters, watchdog timer, and hardware serial communication. Integrated SPI, I2C (TWI), and USART interfaces for seamless connectivity. Operates on 1.8V to 5.5V, suitable for low-power and battery-based projects. 6-channel 10-bit ADC (8-channel in TQFP package) for accurate analog sensing. SMD design ideal for custom PCBs, compact electronics, and embedded projects.

Waveshare 3.5inch Capacitive Touch LCD IPS Display Module 320×480 The Waveshare 3.5-inch Capacitive Touch LCD IPS Display Module is a compact yet powerful display solution featuring a 320 × 480 pixel resolution that delivers crisp visuals and excellent clarity. Designed with an IPS panel, it offers wide viewing angles and consistent color performance, making it ideal for graphical interfaces and interactive applications. The module integrates the ST7796S display driver for reliable display control and the FT6336U capacitive touch controller for accurate, multi-touch responsiveness. Optimized for embedded development, this 3.5 inch LCD Raspberry Pi display is perfectly suited for Raspberry Pi projects, control panels, and custom HMI applications where space, touch precision, and visual quality matter. Features: 320×480 resolution, 262K colors, clear and colorful displaying effect High touch screen transmittance, fast response and long lifetime Embedded with ST7796S driver chip and FT6336U capacitive touch control chip, using SPI and I2C communication respectively, minimizes required IO pins Onboard TF card slot for storing more pictures, videos, music, etc. Adapting 15PIN connector and 18PIN FPC slot for connecting the LCD module to the host board Onboard voltage translator, compatible with 3.3V / 5V operating voltage Comes with online development resources and manual (examples for Raspberry Pi / ESP32 / Raspberry Pi Pico / Arduino) SPI and I2C Control Interfaces: Pin Description 15PIN Pin No. 18PIN Pin No. VCC Power (3.3V / 5V input) 1 1 3V3 Power (3.3V input) 2 NC GND Ground 3 3 MISO SPI MISO pin 4 6 MOSI SPI MOSI pin 5 5 SCLK SPI CLK pin 6 4 SD_CS TF card chip selection, low active 7 10 LCD_CS LCD chip selection, low active 8 9 LCD_DC LCD data/command selection (high for data, low for command) 9 7 LCD_RST LCD reset pin, low active 10 8 LCD_BL LCD backlight pin 11 2 TP_SDA Touch panel data pin 12 14 TP_SCL Touch panel clock pin 13 13 TP_INT Touch panel interrupt pin 14 15 TP_RST Touch panel reset pin, low active 15 12

SmartElex 12V 3A Single Channel Signal Relay Module The SmartElex 12V 3A Single Channel Signal Relay Module is a compact and reliable solution for switching electrical loads using low-power control signals. It allows users to safely control higher-voltage or higher-current devices without direct electrical contact, making it ideal for protecting sensitive control circuits. This module is suitable for students, makers, engineers, educators, and startups who are working on embedded systems, control projects, or automation prototypes that require dependable on-off switching. This single channel relay module is well suited for robotics, IoT systems, home and industrial automation, and general prototyping applications. It can be easily interfaced with popular platforms such as Arduino, Raspberry Pi, and ESP32 to control lights, motors, solenoids, alarms, or other external devices. The simple interface and consistent performance make it easy to integrate into both experimental setups and final products, helping users build reliable control systems with minimal effort. Features: Single channel relay module for switching external loads using low-power control signals Operates on 12V, suitable for industrial and automation environments Supports up to 3A load current for controlling common electrical devices Electrical isolation between control side and load side for added safety Compatible with Arduino, Raspberry Pi, ESP32, and other microcontrollers Compact and easy-to-integrate design for projects and prototyping

Cytron Maker Pi RP2040 – Robotics Controller Board with Raspberry Pi The Cytron Maker Pi RP2040 is a compact, beginner-friendly robotics controller board powered by the Raspberry Pi RP2040 microcontroller. Designed for DIY robotics, automation, and motion-control projects, this board integrates a dual-channel DC motor driver, four servo ports, and seven Grove connectors - giving makers everything they need to build robots without complex wiring. With compatibility across CircuitPython, MicroPython, C/C++, and even the Arduino ecosystem, this board ranks among the best RP2040 robotics controllers for students, hobbyists, and educators. Built for convenience, the Maker Pi RP2040 supports multiple power input options (USB, LiPo battery, or VIN), includes onboard functional test buttons, and features status LEDs for easy debugging. The preloaded demo code lets you start controlling motors, playing melodies, and testing GPIOs right out of the box. Whether you are exploring Raspberry Pi’s RP2040 ecosystem or building an advanced robot, the Cytron Maker Pi RP2040 robot controller offers exceptional versatility, ease of use, and reliable motor-driving performance. Features: Powered by the Raspberry Pi RP2040 dual-core Arm Cortex-M0+ processor. Includes dual-channel DC motor driver and four servo motor ports for robotics. Seven Grove ports support digital, analog, I2C, SPI, and UART expansion. Preloaded with CircuitPython for easy plug-and-play coding. Supports USB 5V, LiPo 1-cell battery, or 3.6–6V VIN input with automatic switching. Built-in LiPo charging circuit with safety protections. Onboard piezo buzzer, RGB LEDs, GPIO test LEDs, and push buttons. Quick-test buttons and motor output LEDs for immediate motor testing. Fully compatible with the Raspberry Pi Pico ecosystem, MicroPython, C/C++, and Arduino cores. Includes LEGO-compatible mounting holes and M3 mounting points. Board Layout: Dimension:

7Semi ESP32-DEVKIT-E – ESP32 WiFi BLE Development Board with CP2102 USB-UART The 7Semi ESP32-DEVKIT-E is a compact and powerful development board built around the ESP32-WROOM-32E module, offering dual-core processing, onboard WiFi, and Bluetooth connectivity. Designed for makers, students, and IoT developers, it provides reliable wireless performance and plenty of GPIO pins to interface with sensors, displays, motors, and more. Whether you're experimenting with automation, creating smart devices, or building connected prototypes, this board gives you the flexibility and power needed to push your ideas further. With a CP2102 USB-to-UART bridge for easy programming, breadboard-friendly spacing, and multiple power input options (USB, 5V, or 3.3V), the ESP32-DEVKIT-E is built for smooth prototyping. It delivers a stable development experience with 4MB Flash, a PCB antenna, and support for protocols like SPI, I2C, I2S, ADC, DAC, and PWM - making it ideal for IoT, robotics, wearables, smart home projects, and low-power connected applications. Features: Powered by the ESP32-WROOM-32E module featuring a dual-core processor running at 160MHz for fast and efficient performance. Integrated WiFi and Bluetooth support enables seamless wireless connectivity for IoT and smart device applications. Includes multiple GPIO pins that allow easy interfacing with sensors, displays, motors, and other electronic components. Breadboard-friendly pin layout ensures easy prototyping and smooth development workflows. Equipped with a CP2102 USB-UART bridge for convenient programming and debugging via USB. Flexible power options including Micro USB, 5V, and 3.3V inputs to suit a wide variety of project needs. Built-in PCB antenna, 4MB flash memory, and compact, cost-effective design ideal for beginners and advanced developers alike. ESP32 Devkit Pinout Diagram:

SmartElex 5V 3A 8 Channel Signal Relay Module The SmartElex 5V 3A 8 Channel Signal Relay Module is a dependable switching solution built to control multiple electrical devices with precision. This 8 Channel Relay Module features eight JY4100F-S-DC5V-C relays, each capable of safely switching loads up to 3A at 120V AC or 24V DC. Designed to operate on a stable 5V supply, it offers individual input triggers and LED indicators for real-time status visibility. With strong electrical isolation and seamless compatibility with Arduino, ESP32, and Raspberry Pi, this 5V relay module is well-suited for automation panels, IoT systems, and complex control applications where reliable multi-channel switching is essential. Applications: Smart home automation (e.g., managing several appliances) Complex industrial automation systems. Robotics projects require several actuators. IoT systems have several relay outputs. Alarms, security, and access control panels Cautions: Use a well regulated 5V supply with adequate current (at least 1A suggested). Ensure that relay load restrictions are not exceeded. To avoid electrical dangers, securely isolate all AC wiring. Maintain a dry, clean, and dust-free atmosphere. Features: An 8-channel relay module with individual control. It operates at 5V DC and has active LOW/HIGH triggers. Each relay can handle 3A at 120V AC or 24V DC. Compatible with Arduino, ESP32, Raspberry Pi, and more platforms. Status LEDs for each channel are used to monitor operation. Fast switching: ≤10 ms operation and ≤5 ms release. Contact resistance of ≤100 mΩ enables stable conductivity. Total power usage is around 2.88W across all channels. High insulation resistance and dielectric strength are essential for safety. Suitable for -40°C to +85°C temperatures.

SmartElex NS612 PIR Motion Sensor Module The SmartElex NS612 PIR Motion Sensor Module is a passive infrared motion detection solution designed to sense human movement by detecting changes in infrared radiation. It helps automate systems by triggering actions only when motion is detected, reducing unnecessary power usage and improving system efficiency. This module is suitable for students, makers, engineers, educators, and startups working on electronics projects that require reliable and responsive motion sensing for security, automation, or interactive applications. This PIR motion sensor module is widely used in robotics, IoT devices, security systems, and home or industrial automation projects where motion detection is essential. It can be easily interfaced with popular development platforms such as Arduino, Raspberry Pi, and ESP32, allowing quick integration into prototypes and working systems. The dependable performance and simple interface make it ideal for applications like motion-activated lighting, alarm systems, smart monitoring solutions, and embedded electronics projects. Features: Passive infrared (PIR) sensor for accurate human motion detection Detects movement by sensing changes in infrared radiation Long sensing range suitable for wider coverage areas Low power consumption for battery-powered applications Digital output for easy interfacing with microcontrollers Compatible with Arduino, Raspberry Pi, ESP32, and similar boards

Cytron SHIELD-3AMOTOR 1.2A Dual Channel 7V–30V DC Motor Driver Shield for Arduino The Cytron SHIELD-3AMOTOR is a high-performance, dual-channel DC motor driver shield designed for Arduino users who need reliable and efficient motor control. Supporting motor voltages from 7V to 30V and delivering up to 3A peak and 1.2A continuous current per channel, this shield is ideal for robotics, automation, DIY RC vehicles, and mechatronics projects. Its compatibility with Arduino UNO, Mega, Leonardo, Zero, 101, and other popular boards makes it a plug-and-play solution for both beginners and advanced makers searching for powerful motor-driving capabilities. Built using the DRV8871 motor driver IC, the Cytron SHIELD-3AMOTOR supports both Signed Magnitude and Locked Anti-Phase control modes via an easy DIP switch selector. Additional features such as current limit protection, stackable headers, quick-test pushbuttons, and direct connectors for the LSS05 auto-calibrating line sensor make this shield perfect for building reliable robot platforms, line-followers, and dual-motor systems. With strong motor handling and seamless Arduino integration, this Cytron shield makes high-current motor control simple, safe, and efficient. Features: Dual-channel brushed DC motor driver shield designed for full Arduino compatibility. Supports 7V–30V motor voltage, suitable for a wide range of DC motors. Handles 3A peak and 1.2A continuous current per channel, ideal for medium-power robotic applications. Built-in current limit protection for safer motor operation. Compatible with 3.3V and 5V logic input, supporting various Arduino boards. DRV8871 IC ensures smooth, efficient, and reliable motor control. Selectable control modes: Signed Magnitude and Locked Anti-Phase via DIP switches. Stackable header pins for easy integration with additional shields. Quick-test switches provided for rapid motor testing on both channels. Includes dedicated connector for Cytron LSS05 Line Sensor, ideal for line-following robots. (Note: No polarity protection for motor supply input - connect with care.)

Cytron URC10 Sumo Robot Controller R1.1 Arduino-Compatible Motor Driver Board The Cytron URC10 Sumo Robot Controller R1.1 is a powerful all-in-one robotics control board designed specifically for competitive sumo robot building. It combines an Arduino-compatible ATmega328P microcontroller, a dual 10A motor driver, and dedicated interfaces for ultrasonic, digital, and analog sensors - making it one of the most efficient and beginner-friendly solutions for robot builders. With support for 8V–25V DC motors, 30A peak current, and high-frequency PWM control, this controller ensures strong pushing power and fast maneuverability for 3kg sumo robot competitions. Cytron engineered the URC10 to simplify robot development by integrating essential hardware like built-in test buttons, motor output LEDs, onboard 5V/3.3V regulators, and a Micro-USB interface for programming. Whether you're designing autonomous systems, competitive sumo robots, or experimenting with robotics, the Cytron URC10 offers reliable performance, stable motor control, and easy sensor expansion for both beginners and advanced makers. Features: Designed specifically for up to 3kg sumo robot applications. Built around the Arduino-compatible ATmega328P microcontroller with Optiboot Bootloader. Integrated dual 10A continuous motor driver (30A peak per channel) for high-power brushed DC motors. Supports 8V–25V motor voltage for a wide range of robot motors. Features current limiting at 30A per channel for safe operation under heavy loads. Includes motor test buttons for quick verification without uploading code. Motor output status LEDs for easier debugging and inspection. Compatible with sign-magnitude and locked-antiphase PWM, supporting up to 20kHz frequency. Onboard 5V, 1A regulator and 3.3V, 500mA regulator for powering sensors and modules. Dedicated pins for motors, ultrasonic sensors, digital I/O, and analog sensors. Includes USB Micro-B + CH340 USB-serial system for easy programming upload. Provides 1× I2C port for additional modules. Compact design with dimensions 75.57mm × 99.7mm. Note: Reverse polarity protection is not included.