SmartElex 5-inch TFT LCD Capacitive Touch Display 800×480

Female to Female Jumper Wires (20cm) 40pcs These are 20cm 40pcs Female to Female Jumper wires, very Flexible and easily detachable. These jumper cables have 1Pin female to the 1pin female header with both ends. Also, it is compatible with 2.54 mm mil spacing pin headers. This cable is an electrical wire or group of them in a cable with a connector or pins at each end, which is normally for interconnecting the components of a breadboard or other prototype or test circuit, internally or with other equipment or components, without soldering. Individual Dupont Cables are fitted by inserting their end connectors into the slots provided in a breadboard, the header connector of a circuit board, or a piece of test equipment. Mostly Dupont cables are useful with Orange Pi, Banana Pi, Raspberry Pi , Arduino , and other mini PCs and development boards . It is very useful in the PCB project, PC motherboard, as well as Breadboard connections. Additionally, these jumper wires allows you to plug and unplug easily for prototyping and can be used over and over again. Check out the best selection of Jumper Wires . Applications: Raspberry Pi Arduino PCB projects Breadboard connections Get a complete set of M2M, M2F, F2F Jumper Wires Set for DIY projects.

A3967 Stepper Motor Driver This A3967 Stepper Motor Driver For Arduino is the most recent version of EasyDriver v44, which was created in collaboration with Brian Schmalz. When compared to previous versions, it offers more flexibility and control over your stepper motor . It is a simple stepper motor driver that is compatible with most microcontrollers and capable of producing a digital 0 to 5V pulse (0 to 3.3V pulse if you solder SJ2 closed on the EasyDriver). A 7V to 30V power supply is required for the module's motor. The digital interface is powered by an onboard voltage regulator that can be set to 5V or 3.3V. The A3967 is a full-featured microstepping motor driver with an integrated transistor. It is intended for use with bipolar stepper motors in full-, half-, quarter-, and eighth-step modes, with output drive capabilities of 30 V and 750 mA. The A3967 comes with a fixed off-time current regulator that can operate in slow, fast, or mixed current-decay modes. This current-decay control scheme produces less audible motor noise, higher step accuracy, and lower power dissipation. The transistor is essential to the A3967's simple implementation. Simply sending one pulse to the STEP input causes the motor to move one step (full, half, quarter, or eighth depending on two logic inputs). It is not necessary to programme phase-sequence tables, high-frequency control lines, or complex interfaces. The A3967 interface is ideal for applications where a complex P is either unavailable or overburdened. Features: A3967 microstepping driver Adjustable current control from 150mA/phase to 750mA/phase MS1 and MS2 pins are broken out to change microstepping resolution to full, half, quarter and eighth steps (defaults to eighth) Compatible with 4, 6, and 8-wire stepper motors of any voltage Breadboard-compatible pins.

CNC Shield for Arduino The CNC shield for Arduino has total four slots, can drive 4 A4988 stepper motors. Each road stepper motors only need two IO ports. In other words, six IO ports can be well managed three stepper motors. The CNC Shield V3.0 allows you to build a engraving machine, 3D printer, mini CNC and other similar devices using your Arduino. It is designed as a shield and can plug on top of an Arduino requiring no external connections and wiring. There are 4 slots on the board for plugging in stepper motor drive module which can drive 1 stepper motor each. Controlling each step stepper motor requires only two IO pins on the Arduino. Just insert this Arduino CNC Shield V3.0 onto an Arduino UNO , and install the GRBL firmware, you can then quickly build a DIY CNC engraving machine. This arduino shield is very convenient to use and is suitable for development boards compatible with Arduino. This CNC shield compatible with Arduino is the latest version of the CN shield model (V 3.0). The CNC Shield is GRBL 0.9 compatible and with the help of jumper wires , it is accessible to stepper drivers. Features: Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place. GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals) 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)

CNC Shield + UNO R3 Board compatible with Arduino + 4xDRV8825 Driver Kit Arduino Uno is an open-source microcontroller used by students and hobbyists entering the world of DIY electronics and automation, The Arduino Uno can be used for any application including being the brains of your next DIY 3D printer and/or CNC router The CNC Shield V3.0 allows you to build an engraving machine, 3D printer, mini CNC and other similar devices using your Arduino. It is designed as a shield and can plug on top of an Arduino requiring no external connections and wiring. Along with that, the CNC shield allows you to control up to four stepper motors by mounting on 4 stepper motor drivers, included with this kit The DRV8825 provides an integrated motor driver solution for printers, scanners, and other automated equipment. The device has two H-bridge and is intended to drive a bipolar stepper motor. Features: UNO R3 Board: The main microcontroller board compatible with Arduino. CNC Shield: An expansion board that allows for easy connection and control of stepper motors. 4x DRV8825 Stepper Motor Drivers: High-performance drivers for controlling stepper motors. Micro-Stepping: Supports micro-stepping settings for precise control of stepper motors. GRBL Compatibility: Compatible with GRBL firmware, which is widely used for CNC control. Voltage Range: Operates on 12-36V DC. Heat Sinks: Included for cooling the stepper motor drivers. USB Cable: For connecting the UNO R3 board to a computer. 40-Pin Row Needles: For additional connections. Applications: CNC Machines: Used for controlling stepper motors in CNC milling, engraving, and cutting machines. 3D Printers: Essential for driving stepper motors in 3D printers, ensuring precise layer deposition and movement. Laser Cutters: Controls stepper motors in laser cutting machines for accurate cutting and engraving. Robotics: Ideal for robotics projects requiring precise motor control, such as robotic arms and automated guided vehicles (AGVs). X-Y Tables: Used in X-Y tables for accurate positioning and movement in various industrial applications. Pick-and-Place Devices: Employed in pick-and-place machines for accurate component placement in electronics manufacturing. Labeling Machines: Used in labeling machines for precise label application. Pinout Diagram for the Arduino Uno Microcontroller Applications of the Kit The kit can be used to create custom 3D printers, scanner, CNC mills and other automated equipment applications

3D Printer 128x64 Smart LCD Display Controller for RAMPS 1.4 This smart LCD kit is a 3D printer 128×64 Smart LCD controller for ramps 1.4 and contains the following components: SD-Card reader Rotary encoder 128×64 LCD display You can easily connect it to your Ramps board using the "smart adapter". After connecting this panel to your Ramps you don't need your pc anymore, the Smart Controller supplies power for your SD card. Furthermore, all actions like calibration, axes movements can be done by just using the rotary encoder on the Smart Controller. Print your 3D designs without PC, just with a g-code design stored on the SD card. This panel connects to your RAMPS 1.4 All further operations, such as calibration, the axis movement can be done with the rotary encoder embedded. The SD card slot is integrated at the back so that the files to be printed can be read here. It is used to use since all you need to do is plug and play on the RAMPS. Check out : 1.75mm Luminous White ABS Filament -1Kg

3D Printer - LCD 2004 Graphic Smart Display The intelligent controller includes an sd card reader, rotary encoders and a 20-character — 4 line lcd display. You can easily connect it to your ramps 1. 4 Board using "smart adapter" included. This panel connect your ramps 1. 4, You do not need your computer, your sd card intelligent controller power supply. All further operations, such as calibration, the axis movement can be done only with a rotary encoder intelligent controller. 3D design print without a computer, just use the g code design stored on the sd card.

Holybro Power Module PM02 The Holybro Power Module PM02 is a precision-engineered power module designed to supply clean, regulated voltage and current to your drone’s flight controller and onboard electronics. Built for reliability and accuracy, this module ensures your system receives stable power directly from the battery while continuously monitoring real-time voltage and current data. Its compact design and robust connectors make it ideal for a wide range of UAV platforms, from hobbyist builds to advanced autonomous drones. Engineered to integrate seamlessly with popular flight controllers, the PM02 power module not only simplifies wiring and installation but also enhances safety through over-current and over-voltage protection. Whether you’re building a custom multirotor, fixed-wing aircraft, or research UAV, this power module provides dependable energy management so you can focus on performance and flight control precision without compromise. Note: This PM02 Power Module uses analog data output and is not compatible to the Pixhawk 5X (Requires a digital PM like PM02D). Features: High-quality power module designed to deliver stable and regulated power to drone flight controllers and onboard electronics. Provides real-time voltage and current sensing for accurate battery monitoring and improved flight safety. Ensures clean power output, reducing electrical noise and improving overall system reliability. Simplifies wiring and installation by combining power supply and monitoring in a single compact module. Built for compatibility with a wide range of drone flight controllers and UAV platforms. Ideal for multirotor, fixed-wing, and professional UAV applications requiring dependable power management.

SmartElex MicroB USB Breakout Board The SmartElex MicroB USB Breakout Board is a compact adapter board designed to make it easy to access the pins of a Micro-B USB connector for prototyping, development, and testing. It breaks out the USB port into simple pin headers, allowing users to interface USB power and data lines with custom circuits, breadboards, and microcontroller boards. This USB breakout board is ideal for students, makers, educators, and engineers who need a quick and reliable way to add USB connectivity to their electronics projects without designing a custom PCB. This board is commonly used in robotics, IoT applications, embedded system development, device repair, and hardware prototyping where USB access is required for powering circuits or transferring data. It works smoothly with platforms like Arduino, Raspberry Pi, and ESP32, enabling fast integration with both beginner and advanced projects. With its straightforward layout and sturdy connector design, the SmartElex MicroB USB Breakout Board is a practical and efficient choice for workshops, prototyping labs, and DIY electronic builds that require stable Micro-B USB interfacing Features: Micro-B USB connector broken out to easy-to-use header pins Simplifies USB power and data access for prototyping and testing Supports quick integration with breadboards and custom circuits Compatible with Arduino, Raspberry Pi, ESP32, and microcontrollers Ideal for DIY repairs, IoT projects, and embedded hardware development Compact and beginner-friendly design for rapid project setup

Waveshare 3.5inch Capacitive Touch LCD IPS Display Module 320×480 The Waveshare 3.5-inch Capacitive Touch LCD IPS Display Module is a compact yet powerful display solution featuring a 320 × 480 pixel resolution that delivers crisp visuals and excellent clarity. Designed with an IPS panel, it offers wide viewing angles and consistent color performance, making it ideal for graphical interfaces and interactive applications. The module integrates the ST7796S display driver for reliable display control and the FT6336U capacitive touch controller for accurate, multi-touch responsiveness. Optimized for embedded development, this 3.5 inch LCD Raspberry Pi display is perfectly suited for Raspberry Pi projects, control panels, and custom HMI applications where space, touch precision, and visual quality matter. Features: 320×480 resolution, 262K colors, clear and colorful displaying effect High touch screen transmittance, fast response and long lifetime Embedded with ST7796S driver chip and FT6336U capacitive touch control chip, using SPI and I2C communication respectively, minimizes required IO pins Onboard TF card slot for storing more pictures, videos, music, etc. Adapting 15PIN connector and 18PIN FPC slot for connecting the LCD module to the host board Onboard voltage translator, compatible with 3.3V / 5V operating voltage Comes with online development resources and manual (examples for Raspberry Pi / ESP32 / Raspberry Pi Pico / Arduino) SPI and I2C Control Interfaces: Pin Description 15PIN Pin No. 18PIN Pin No. VCC Power (3.3V / 5V input) 1 1 3V3 Power (3.3V input) 2 NC GND Ground 3 3 MISO SPI MISO pin 4 6 MOSI SPI MOSI pin 5 5 SCLK SPI CLK pin 6 4 SD_CS TF card chip selection, low active 7 10 LCD_CS LCD chip selection, low active 8 9 LCD_DC LCD data/command selection (high for data, low for command) 9 7 LCD_RST LCD reset pin, low active 10 8 LCD_BL LCD backlight pin 11 2 TP_SDA Touch panel data pin 12 14 TP_SCL Touch panel clock pin 13 13 TP_INT Touch panel interrupt pin 14 15 TP_RST Touch panel reset pin, low active 15 12

SmartElex 12V 10A Single Channel Power Relay Module The SmartElex 12V 10A Single Channel Power Relay Module is a reliable switching solution designed to control high-power electrical loads using low-voltage control signals. It helps safely operate devices that draw higher current without directly connecting them to sensitive control circuits. This module is suitable for students, makers, engineers, educators, and startups who are working on electronics projects, automation systems, or prototypes that require dependable and safe power switching. This single channel power relay module is widely used in robotics, IoT applications, home automation, and industrial control projects where motors, lights, pumps, or appliances need to be switched on and off reliably. It can be easily interfaced with popular platforms such as Arduino, Raspberry Pi, and ESP32, making integration simple for both learning projects and real-world systems. The sturdy design and consistent performance make it a practical choice for prototyping as well as final deployment in power control applications. Features: Single channel power relay module for high-current load switching Operates on 12V, suitable for automation and control applications Supports up to 10A load current for power devices Electrical isolation between control and load circuits for safety Compatible with Arduino, Raspberry Pi, ESP32, and similar boards Compact and durable design for easy integration

Anycubic Kobra 3 Max 3D Printer – EU power plug The Anycubic Kobra 3 Max 3D Printer – EU power plug is a high-performance large-format FDM 3D printer designed for fast, precise, and large-scale printing. With an expansive build volume, it allows users to create bigger models or multiple parts in a single print, making it ideal for professional prototyping, product design, and advanced DIY projects. Equipped with high-speed printing capabilities and intelligent automation features, it delivers consistent results with minimal manual intervention. Models Created Built for efficiency and ease of use, the printer features advanced auto bed leveling technology for perfect first layers, a stable dual-axis motion system for reduced vibrations, and a high-temperature hotend compatible with a wide range of filaments. The EU power plug ensures compatibility with standard 220–240V power systems. Whether for industrial use, educational labs, or creative projects, this 3D printer offers reliable performance and excellent print quality. 420*420*500mm Print Volume The massive 420 × 420 × 500 mm print volume of the Anycubic Kobra 3 Max enables users to create large-scale models in a single print without the need to split designs into multiple parts. This expansive build area is ideal for producing full-sized prototypes, architectural models, and functional components with greater efficiency and precision. It significantly reduces assembly time and improves structural strength since parts can be printed as one complete piece. Printing Speed Up to 600mm/s With a printing speed of up to 600 mm/s, the Anycubic Kobra 3 Max is designed to deliver rapid production without compromising on print quality. This high-speed capability significantly reduces overall printing time, allowing users to complete large models and batch prints much faster than traditional 3D printers. It is especially beneficial for professionals and businesses that require quick prototyping and efficient workflow. Despite the speed, the printer maintains stability and precision through its advanced motion system, ensuring clean layers and accurate results. Precise Auto-Leveling & Motor Anti-skip The printer features an advanced auto-leveling system that ensures the print bed is perfectly calibrated before every print, eliminating the need for manual adjustments and reducing setup time. This precise leveling improves first-layer adhesion, which is crucial for achieving high-quality and successful prints. In addition, the motor anti-skip mechanism enhances movement accuracy by preventing step loss during high-speed operations. This results in smoother motion, better layer consistency, and reduced chances of print failure. Extremely Easy to Use The printer is designed with user convenience in mind, making it extremely easy to use for both beginners and experienced users. Its intuitive interface and guided setup process allow you to get started quickly without any technical complexity. Features like automatic bed leveling and pre-configured settings reduce manual effort and minimize errors during printing. The streamlined design ensures smooth operation, while simple controls make monitoring and adjusting prints hassle-free. Features: Massive build volume for large-scale 3D printing High-speed printing capability for improved productivity Intelligent auto bed leveling system for perfect first layers High-temperature hotend supporting multiple materials Dual motor-driven axis for enhanced stability and accuracy User-friendly interface for easy operation Compatible with popular slicing software Durable and rigid frame for consistent performance Suitable for prototyping, manufacturing, and creative projects

DIY 51 MCU Electronic Clock Kit (Red) – 1" Light-Control LED Display with Assembly Case for STEM Projects This DIY 51 MCU Electronic Clock Kit offers an engaging way to learn core electronics and microcontroller concepts. It features a clear 1-inch LED digital display paired with an intelligent light-control function, ensuring visibility in different lighting conditions. The kit comes unassembled, allowing learners to understand every part of the build, from wiring to mounting, while gaining confidence in practical electronics. Designed for STEM and STEAM education, this kit encourages curiosity, experimentation, and hands-on problem-solving. It's an excellent tool for students, hobbyists, and makers looking to explore timekeeping circuits and microcontroller basics. Whether used in classrooms or at home, it helps develop creativity, scientific thinking, and technical skills through a fun, interactive building experience. Features: DIY microcontroller-based clock kit for hands-on learning and experimentation. Equipped with a bright 1-inch LED digital display and automatic light-control function. Includes pre-cut housing and all necessary electronic parts for easy assembly. Supports STEM/STEAM skill development in electronics, engineering, and problem-solving. Helps nurture creativity, observation, and practical building ability. Suitable for home learning, school labs, and maker workshops. Comes with a study-style instruction manual for guided learning.

HGLRC SPECTER F460 Electronic Stack with 4-in-1 ESC The HGLRC SPECTER F460 Electronic Stack with 4-in-1 ESC is engineered to deliver high-performance flight control and efficient power management for FPV drone builds. Combining a flight controller with a 4-in-1 ESC, it provides seamless integration and precise motor control, ensuring smooth and responsive flight characteristics. Equipped with advanced gyroscopic sensors, the stack enhances stability and accuracy, making it ideal for high-speed racing and freestyle flying. Its compact form factor and robust construction allow easy installation while maintaining durability under demanding conditions, making it a reliable choice for both professional racers and hobbyists. Features: The flight control uses an exceptionally steady MPU6000 gyroscope. The flight control primary control chip uses the F405 chip, and the serial connection allows up to four groups, resulting in faster operation and smoother control. The primary chip of the ESC picks a new imported FD6288 processor, which is matched with ON3109 high-performance MOS, and can constantly sustain current and steady output. The socket allows for rapid connection to the camera, receiver, picture transmission, LED, or GPS without the need for welding. Maximum support for BEC 9V2A/BEC 5V2.5A, capable of providing reliable voltage and current output to external devices. The immersion gold high-tech design is temperature- and current-resistant, the ESC has a large pad, and the flight controller is directly plugged in, so there is no issue welding. The integrated 16M black box may record flight data. Onboard galvanometer module, real-time display of data, such as current feedback via the flight control

HGLRC ZEUS VTX 2.5W The HGLRC ZEUS VTX 2.5W is a high-performance video transmitter engineered for FPV (First Person View) drones, delivering exceptional video clarity and long-range transmission. With a powerful 2.5W output, it ensures a strong, stable signal even in challenging environments, making it perfect for both long-distance flights and demanding racing conditions. It supports multiple frequency bands, providing flexibility and compatibility with a wide range of FPV systems. The built-in Smart Audio functionality allows pilots to easily adjust channels, bands, and power levels directly through their flight controller, ensuring quick and hassle-free configuration. Designed with efficiency and durability in mind, the ZEUS VTX features excellent heat dissipation for consistent performance during extended flights. Its compact and lightweight design makes it easy to integrate into various drone builds without adding unnecessary bulk. Ideal for competitive racing, freestyle flying, and long-range FPV enthusiasts, this VTX offers reliable performance and enhanced control for an immersive flying experience. Features: Achieves up to 9 km range in urban environments with interference (tested near a lake), and can exceed 10 km in suburban or mountainous areas. High 2500mW output power ensures strong and consistent signal transmission, ideal for long-range and ultra-long-distance flights. Offers 6 adjustable power levels: PIT / 25mW / 200mW / 800mW / 1600mW / 2500mW for flexible performance tuning. CNC-machined integrated top and bottom shell provides excellent heat dissipation, ensuring stable performance during extended use. Equipped with dual-function buttons for easy parameter adjustments, along with 3 LED indicators for quick viewing of power, band, and channel settings. Supports IRC Tramp protocol, allowing convenient OSD-based parameter configuration through the flight controller. Wide input voltage support of 2–6S (7–26V), making it compatible with various drone setups. Standard 30.5 × 30.5 mm M3 mounting holes for easy and secure installation.

Cytron UNO Special Edition – Arduino-Compatible Board with Side Connectors The Cytron UNO Special Edition (CT-UNO-SE) is a fully Arduino-compatible development board designed for makers, students, and hobbyists who need reliable performance for DIY electronics and robotics projects. Built around the ATmega328P microcontroller, this board offers the familiar Arduino UNO experience while adding enhanced stability with the FTDI FT231X USB-to-Serial chip, ensuring smoother programming and communication. Whether you're prototyping sensors, robotics circuits, or automation systems, this board delivers a dependable and beginner-friendly platform for all your microcontroller learning needs. What makes the CT-UNO-SE stand out is its unique side connectors, allowing it to be stacked on top of or beneath Arduino shields, giving you maximum flexibility while building layered circuits or compact embedded systems. With full Arduino UNO R3 shield compatibility, 14 digital I/O pins, 6 analog inputs, and both 5V and 3.3V regulated outputs, this special edition board combines convenience, versatility, and long-term durability - all wrapped into a sleek white PCB that makes your projects look clean and professional. Features Built with the ATmega328P microcontroller paired with the Optiboot bootloader for faster program uploads. Equipped with the FTDI FT231X USB interface, offering stable and reliable serial communication. Supports a wide DC input range of 7–15V, suitable for most maker power setups. Includes a 1A 5V regulator and 500mA 3.3V regulator for powering sensors and modules. Offers 14 digital I/O pins (6 PWM) and 6 analog inputs for versatile interfacing. Fully R3 shield compatible with special side connectors for flexible stacking. Features 32KB Flash memory, 2KB SRAM, and 1KB EEPROM for program storage. Comes with easily visible TX, RX, power, and pin-13 LEDs placed on the board edge. Utilizes a durable USB Micro-B connector on a clean white PCB. Dimensions