Cytron SC08A 8-Channel Servo Controller

Female to Female Jumper Wires (20cm) 40pcs These are 20cm 40pcs Female to Female Jumper wires, very Flexible and easily detachable. These jumper cables have 1Pin female to the 1pin female header with both ends. Also, it is compatible with 2.54 mm mil spacing pin headers. This cable is an electrical wire or group of them in a cable with a connector or pins at each end, which is normally for interconnecting the components of a breadboard or other prototype or test circuit, internally or with other equipment or components, without soldering. Individual Dupont Cables are fitted by inserting their end connectors into the slots provided in a breadboard, the header connector of a circuit board, or a piece of test equipment. Mostly Dupont cables are useful with Orange Pi, Banana Pi, Raspberry Pi , Arduino , and other mini PCs and development boards . It is very useful in the PCB project, PC motherboard, as well as Breadboard connections. Additionally, these jumper wires allows you to plug and unplug easily for prototyping and can be used over and over again. Check out the best selection of Jumper Wires . Applications: Raspberry Pi Arduino PCB projects Breadboard connections Get a complete set of M2M, M2F, F2F Jumper Wires Set for DIY projects.

A3967 Stepper Motor Driver This A3967 Stepper Motor Driver For Arduino is the most recent version of EasyDriver v44, which was created in collaboration with Brian Schmalz. When compared to previous versions, it offers more flexibility and control over your stepper motor . It is a simple stepper motor driver that is compatible with most microcontrollers and capable of producing a digital 0 to 5V pulse (0 to 3.3V pulse if you solder SJ2 closed on the EasyDriver). A 7V to 30V power supply is required for the module's motor. The digital interface is powered by an onboard voltage regulator that can be set to 5V or 3.3V. The A3967 is a full-featured microstepping motor driver with an integrated transistor. It is intended for use with bipolar stepper motors in full-, half-, quarter-, and eighth-step modes, with output drive capabilities of 30 V and 750 mA. The A3967 comes with a fixed off-time current regulator that can operate in slow, fast, or mixed current-decay modes. This current-decay control scheme produces less audible motor noise, higher step accuracy, and lower power dissipation. The transistor is essential to the A3967's simple implementation. Simply sending one pulse to the STEP input causes the motor to move one step (full, half, quarter, or eighth depending on two logic inputs). It is not necessary to programme phase-sequence tables, high-frequency control lines, or complex interfaces. The A3967 interface is ideal for applications where a complex P is either unavailable or overburdened. Features: A3967 microstepping driver Adjustable current control from 150mA/phase to 750mA/phase MS1 and MS2 pins are broken out to change microstepping resolution to full, half, quarter and eighth steps (defaults to eighth) Compatible with 4, 6, and 8-wire stepper motors of any voltage Breadboard-compatible pins.

CNC Shield for Arduino The CNC shield for Arduino has total four slots, can drive 4 A4988 stepper motors. Each road stepper motors only need two IO ports. In other words, six IO ports can be well managed three stepper motors. The CNC Shield V3.0 allows you to build a engraving machine, 3D printer, mini CNC and other similar devices using your Arduino. It is designed as a shield and can plug on top of an Arduino requiring no external connections and wiring. There are 4 slots on the board for plugging in stepper motor drive module which can drive 1 stepper motor each. Controlling each step stepper motor requires only two IO pins on the Arduino. Just insert this Arduino CNC Shield V3.0 onto an Arduino UNO , and install the GRBL firmware, you can then quickly build a DIY CNC engraving machine. This arduino shield is very convenient to use and is suitable for development boards compatible with Arduino. This CNC shield compatible with Arduino is the latest version of the CN shield model (V 3.0). The CNC Shield is GRBL 0.9 compatible and with the help of jumper wires , it is accessible to stepper drivers. Features: Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place. GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals) 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)

CNC Shield + UNO R3 Board compatible with Arduino + 4xDRV8825 Driver Kit Arduino Uno is an open-source microcontroller used by students and hobbyists entering the world of DIY electronics and automation, The Arduino Uno can be used for any application including being the brains of your next DIY 3D printer and/or CNC router The CNC Shield V3.0 allows you to build an engraving machine, 3D printer, mini CNC and other similar devices using your Arduino. It is designed as a shield and can plug on top of an Arduino requiring no external connections and wiring. Along with that, the CNC shield allows you to control up to four stepper motors by mounting on 4 stepper motor drivers, included with this kit The DRV8825 provides an integrated motor driver solution for printers, scanners, and other automated equipment. The device has two H-bridge and is intended to drive a bipolar stepper motor. Features: UNO R3 Board: The main microcontroller board compatible with Arduino. CNC Shield: An expansion board that allows for easy connection and control of stepper motors. 4x DRV8825 Stepper Motor Drivers: High-performance drivers for controlling stepper motors. Micro-Stepping: Supports micro-stepping settings for precise control of stepper motors. GRBL Compatibility: Compatible with GRBL firmware, which is widely used for CNC control. Voltage Range: Operates on 12-36V DC. Heat Sinks: Included for cooling the stepper motor drivers. USB Cable: For connecting the UNO R3 board to a computer. 40-Pin Row Needles: For additional connections. Applications: CNC Machines: Used for controlling stepper motors in CNC milling, engraving, and cutting machines. 3D Printers: Essential for driving stepper motors in 3D printers, ensuring precise layer deposition and movement. Laser Cutters: Controls stepper motors in laser cutting machines for accurate cutting and engraving. Robotics: Ideal for robotics projects requiring precise motor control, such as robotic arms and automated guided vehicles (AGVs). X-Y Tables: Used in X-Y tables for accurate positioning and movement in various industrial applications. Pick-and-Place Devices: Employed in pick-and-place machines for accurate component placement in electronics manufacturing. Labeling Machines: Used in labeling machines for precise label application. Pinout Diagram for the Arduino Uno Microcontroller Applications of the Kit The kit can be used to create custom 3D printers, scanner, CNC mills and other automated equipment applications

Cytron SHIELD-3AMOTOR 1.2A Dual Channel 7V–30V DC Motor Driver Shield for Arduino The Cytron SHIELD-3AMOTOR is a high-performance, dual-channel DC motor driver shield designed for Arduino users who need reliable and efficient motor control. Supporting motor voltages from 7V to 30V and delivering up to 3A peak and 1.2A continuous current per channel, this shield is ideal for robotics, automation, DIY RC vehicles, and mechatronics projects. Its compatibility with Arduino UNO, Mega, Leonardo, Zero, 101, and other popular boards makes it a plug-and-play solution for both beginners and advanced makers searching for powerful motor-driving capabilities. Built using the DRV8871 motor driver IC, the Cytron SHIELD-3AMOTOR supports both Signed Magnitude and Locked Anti-Phase control modes via an easy DIP switch selector. Additional features such as current limit protection, stackable headers, quick-test pushbuttons, and direct connectors for the LSS05 auto-calibrating line sensor make this shield perfect for building reliable robot platforms, line-followers, and dual-motor systems. With strong motor handling and seamless Arduino integration, this Cytron shield makes high-current motor control simple, safe, and efficient. Features: Dual-channel brushed DC motor driver shield designed for full Arduino compatibility. Supports 7V–30V motor voltage, suitable for a wide range of DC motors. Handles 3A peak and 1.2A continuous current per channel, ideal for medium-power robotic applications. Built-in current limit protection for safer motor operation. Compatible with 3.3V and 5V logic input, supporting various Arduino boards. DRV8871 IC ensures smooth, efficient, and reliable motor control. Selectable control modes: Signed Magnitude and Locked Anti-Phase via DIP switches. Stackable header pins for easy integration with additional shields. Quick-test switches provided for rapid motor testing on both channels. Includes dedicated connector for Cytron LSS05 Line Sensor, ideal for line-following robots. (Note: No polarity protection for motor supply input - connect with care.)

Radiolink FPV Mobile Phone Holder Stand Folding Mount for RC4GS V3/V2 & RC6GS V3/V2 Controllers The Radiolink FPV Display Monitor Screen Holder is designed to securely hold mobile phones or FPV display screens on your RC controller. Simply insert the mount into the controller’s 1/4” (M6) thread hole, place your phone or monitor on the holder, and adjust the angle using the 360° rotating ball head. This makes it easy to achieve the perfect viewing position while flying, whether indoors or outdoors. This foldable and lightweight holder extends from 5.5cm to 9cm, supporting FPV monitors up to 4.3 inches and mobile phones up to 6.8 inches. Compatible with Radiolink RC4GS V2/V3, RC6GS V2/V3, and other devices with a standard thread hole, it is made of durable plastic and metal to withstand impact. Weighing only 105g, it is easy to install, remove, and carry, making it a reliable accessory for FPV enthusiasts. Features: Holds mobile phones or FPV display monitors securely 360° adjustable ball head for optimal viewing angles Extendable from 5.5cm to 9cm Supports FPV monitors up to 4.3 inches and phones up to 6.8 inches Compatible with Radiolink RC4GS V2/V3, RC6GS V2/V3, and devices with 1/4” (M6) thread hole Lightweight and durable, made of plastic and metal Easy to install, remove, and carry

Cytron SHIELD-MD10 – 10A 7V–30V DC Motor Driver Shield for Arduino The Cytron SHIELD-MD10 is a high-performance 10A DC motor driver shield designed for Arduino and compatible development boards. Built specifically for brushed DC motors, it supports 7V–30V motor voltage and delivers up to 10A continuous current, making it ideal for robotics, automation, RC systems, DIY machines, and educational electronics. With solid-state MOSFETs and a fully NMOS H-Bridge design, the Cytron SHIELD-MD10 ensures efficient, fast, and reliable motor control without the need for a heatsink, helping creators achieve accurate speed and direction control with minimal wiring. Optimized for maximum compatibility, the shield stacks directly onto popular boards like Arduino UNO R3, Arduino Mega 2560, Maker UNO, Maker UNO Plus, Arduino Leonardo, CT-UNO, and CT-ARM. Featuring selectable digital pins for PWM and DIR, stackable headers, and regenerative braking, the Cytron SHIELD-MD10 offers unmatched flexibility for robotics and mechatronics projects. Whether you're building a DIY robot, conveyor system, or motorized prototype, this durable and high-current driver shield delivers smooth performance and long-lasting reliability. Features: Bi-directional control for one brushed DC motor with smooth speed and direction adjustment. Supports motor voltage from 7V–25V (Rev 1.0) and 7V–30V (Rev 2.0). Delivers 10A continuous and 15A peak current for high-torque applications. Uses fully solid-state components with NMOS H-Bridge for high efficiency. No heatsink required thanks to low-loss MOSFET design. Supports both 3.3V and 5V logic inputs, making it compatible with multiple controllers. Regenerative braking for safe and controlled stopping. Stackable pin headers allow adding more Arduino shields. Selectable digital pins for PWM and direction via jumpers. PWM frequency supported up to 10 kHz for fine speed control.

SmartElex 5V 3A 4 Channel Signal Relay Module The SmartElex 5V 3A 4 Channel Signal Relay Module is a compact and reliable 4 Channel Relay Module designed to control four independent medium-power loads with precision. Powered as a 5V relay module, it integrates high-quality JY4100F-S-DC5V-C relays, each capable of switching up to 3A at 120V AC or 24V DC. With dedicated trigger inputs and LED status indicators for every channel, it allows easy monitoring and accurate switching. This module directly interfaces with popular microcontrollers such as Arduino, ESP8266, and Raspberry Pi, making it ideal for IoT, home automation, and embedded control applications where safety, isolation, and consistent performance are essential. Applications: Home automation (controlled lights, fans, and locks) Industrial machine control IoT multi-device projects. Robotics and Motor Control Security systems and alarms. Cautions: Always utilize a properly regulated 5V power supply. Avoid exceeding the rated load capacity. Provide proper isolation for AC loads. Store the module in a dry, clean place. Features: Four-channel relay module allows for independent control of four devices. Operates at 5V DC and has an active LOW/HIGH trigger. Each relay can handle up to 3A at 120V AC or 24V DC. Compatible with Arduino, ESP8266, Raspberry Pi, and more platforms. Each channel has its own set of LED indicators. Fast switching: ≤10 ms operation and ≤5 ms release time. Low contact resistance (≤100 mΩ) ensures effective operation. The total power consumption is around 1.44W over four channels. High insulation resistance and dielectric strength are essential for safety. Wide operational temperature range (-40°C to +85°C).

SmartElex 12V 20A Single Channel Power Relay Module The SmartElex 12V 20A Single Channel Power Relay Module is a high-current switching solution designed to control heavy electrical loads using low-voltage control signals. It helps safely operate high-power devices without directly exposing microcontrollers or control circuits to high current, reducing risk and improving system reliability. This module is suitable for students, makers, engineers, educators, and startups who are working on power control, automation, or embedded electronics projects that demand robust switching capability. This single channel power relay module is ideal for robotics, IoT systems, home and industrial automation, and power management applications where devices such as motors, heaters, pumps, or high-load appliances need reliable control. It can be easily interfaced with popular platforms like Arduino, Raspberry Pi, and ESP32, making it convenient for both prototyping and deployment. The strong build quality and straightforward integration make it a dependable choice for projects requiring consistent and safe high-current switching. Features: Single channel power relay module for high-current load control Operates on 12V, suitable for industrial and automation systems Supports heavy load switching up to 20A Electrical isolation between control and power circuits for safety Compatible with Arduino, Raspberry Pi, ESP32, and similar controllers Robust design for reliable operation in power control applications

SmartElex RS-485 (SP3485) Transceiver Breakout Module The SmartElex RS-485 (SP3485) Transceiver Breakout Module is a compact and reliable solution for enabling RS485 module based communication in electronics and automation projects. Designed to simplify long-distance and noise-resistant data transfer, it helps overcome the limitations of standard serial communication in industrial and field environments. This module is ideal for students, hobbyists, engineers, educators, and startups working on projects that require stable, differential signal communication for robotics, industrial controls, or embedded systems. With support for rs485 transceiver based networking, this board makes it easy to add rs485 communication to microcontrollers and development boards like Arduino, Raspberry Pi, and ESP32. Its breakout form factor allows quick integration into prototypes, IoT setups, and automation systems where devices need to communicate over long cables and noisy electrical environments. Whether used for sensor networks, building management systems, or PLC interfacing, it offers dependable performance that helps users build scalable and robust communication links without unnecessary complexity. Features: Enables RS485 module communication for long-distance, noise-resistant data transfer Based on the SP3485 transceiver for stable rs485 transceiver performance Supports differential signal communication ideal for industrial and field environments Easy-to-use breakout format for quick prototyping and integration Works with popular controllers such as Arduino, Raspberry Pi, and ESP32 Helps implement multi-node networks over twisted pair cabling Compact design suitable for compact robotics, IoT, and automation projects Provides reliable rs485 communication without complex wiring or circuitry

DFRobot Gravity 7/24 Industrial Analog pH Sensor Meter Kit for Arduino The DFRobot Gravity 7/24 Industrial Analog pH Sensor Meter Kit for Arduino is a high-precision Analog pH Sensor designed for professional and industrial applications requiring continuous pH monitoring. This Arduino pH Sensor uses an industrial-grade glass membrane electrode with low impedance, delivering fast response, excellent thermal stability, and stable performance over long periods. It supports a full measurement range of 0 pH to 14 pH with linear voltage output, ensuring accurate and reliable readings. The sensor integrates easily through a BNC connector and PH2.0 interface, allowing direct connection to any Arduino analog input. Its reference system, based on Ag/AgCl gel electrolyte with a PTFE membrane, provides strong anti-pollution characteristics and prevents clogging, making it an ideal industrial pH sensor for Arduino for water treatment systems, environmental monitoring, and laboratory analysis. Attention: The probe's bottle top contains protective fluids (3.3mol/L KCL). Even if the bottle cap is tightly fastened, some protective liquid may leak around it, resulting in white crystals. However, as long as the bottle top contains protective liquid, the probe's life and accuracy will be unaffected. Please use it with confidence. It is recommended that the white crystals be returned to the bottle cap's protective liquid. Features Industrial-grade Analog pH Sensor for accurate measurement Compatible with Arduino and other microcontrollers Measures pH range from 0 to 14 Fast response with high stability BNC connector for secure sensor connection Plug-and-play PH2.0 analog interface Built-in power indicator LED Suitable for long-term online monitoring Low maintenance and long sensor life Ideal for water quality and lab applications Applications Water Quality Surveillance Aquaculture

Waveshare 3.5inch Capacitive Touch LCD IPS Display Module 320×480 The Waveshare 3.5-inch Capacitive Touch LCD IPS Display Module is a compact yet powerful display solution featuring a 320 × 480 pixel resolution that delivers crisp visuals and excellent clarity. Designed with an IPS panel, it offers wide viewing angles and consistent color performance, making it ideal for graphical interfaces and interactive applications. The module integrates the ST7796S display driver for reliable display control and the FT6336U capacitive touch controller for accurate, multi-touch responsiveness. Optimized for embedded development, this 3.5 inch LCD Raspberry Pi display is perfectly suited for Raspberry Pi projects, control panels, and custom HMI applications where space, touch precision, and visual quality matter. Features: 320×480 resolution, 262K colors, clear and colorful displaying effect High touch screen transmittance, fast response and long lifetime Embedded with ST7796S driver chip and FT6336U capacitive touch control chip, using SPI and I2C communication respectively, minimizes required IO pins Onboard TF card slot for storing more pictures, videos, music, etc. Adapting 15PIN connector and 18PIN FPC slot for connecting the LCD module to the host board Onboard voltage translator, compatible with 3.3V / 5V operating voltage Comes with online development resources and manual (examples for Raspberry Pi / ESP32 / Raspberry Pi Pico / Arduino) SPI and I2C Control Interfaces: Pin Description 15PIN Pin No. 18PIN Pin No. VCC Power (3.3V / 5V input) 1 1 3V3 Power (3.3V input) 2 NC GND Ground 3 3 MISO SPI MISO pin 4 6 MOSI SPI MOSI pin 5 5 SCLK SPI CLK pin 6 4 SD_CS TF card chip selection, low active 7 10 LCD_CS LCD chip selection, low active 8 9 LCD_DC LCD data/command selection (high for data, low for command) 9 7 LCD_RST LCD reset pin, low active 10 8 LCD_BL LCD backlight pin 11 2 TP_SDA Touch panel data pin 12 14 TP_SCL Touch panel clock pin 13 13 TP_INT Touch panel interrupt pin 14 15 TP_RST Touch panel reset pin, low active 15 12

SmartElex BX604 PIR Motion Sensor Module The SmartElex BX604 PIR Motion Sensor Module is a passive infrared motion detection solution designed to sense human movement by detecting changes in infrared radiation. It helps automate electronic systems by triggering actions only when motion is present, improving efficiency and reducing unnecessary power usage. This module is suitable for students, makers, engineers, educators, and startups who need a dependable motion sensing solution for electronics projects, learning kits, and prototype development. This PIR motion sensor module is widely used in robotics, IoT applications, security systems, and home or industrial automation projects where accurate motion detection is required. It can be easily interfaced with popular development platforms such as Arduino, Raspberry Pi, and ESP32, allowing quick integration into working systems. The wide detection coverage and stable performance make it ideal for applications like motion-activated lighting, alarm systems, smart monitoring devices, and interactive electronic projects. Features: Passive infrared (PIR) sensor for reliable human motion detection Detects movement by sensing changes in infrared radiation Wide detection angle for broader area coverage Long sensing range suitable for security and automation use Low power consumption for battery-operated projects Compatible with Arduino, Raspberry Pi, ESP32, and similar boards

SmartElex PAM8403 5V Two-Channel Stereo Mini Class-D Audio Amplifier The SmartElex PAM8403 5V Two-Channel Stereo Mini Class-D Audio Amplifier is a compact audio amplification module designed to deliver clear and efficient stereo sound from low-power audio sources. It solves the need for adding audio output to small electronic projects without bulky components or complex circuits. This module is suitable for students, makers, engineers, educators, and startups who want an easy way to integrate stereo audio into DIY electronics, learning kits, and embedded system prototypes. This stereo mini Class-D audio amplifier is commonly used in robotics, IoT devices, automation systems, and portable electronics that require lightweight and power-efficient audio output. It can be easily interfaced with platforms such as Arduino, Raspberry Pi, and ESP32 to drive small speakers in projects like voice alerts, sound feedback systems, and interactive devices. The simple design and stable performance make it easy to integrate into both prototype builds and finished products, enabling reliable audio output with minimal setup effort. Features: Two-channel stereo Class-D audio amplifier for clear sound output Operates on a 5V power supply, ideal for embedded projects High efficiency design with low heat generation Compact size suitable for space-constrained applications Drives small speakers for stereo audio output Compatible with Arduino, Raspberry Pi, ESP32, and other audio-enabled projects

Cytron Maker UNO Plus – Arduino-Compatible Educational Board The Cytron Maker UNO Plus is a beginner-friendly, Arduino-compatible development board designed to simplify electronics and coding for students, educators, and STEM hobbyists. With onboard LEDs, a built-in piezo buzzer, a programmable pushbutton, and upgraded components, this board removes wiring complexity allowing learners to focus on coding, debugging, and hands-on exploration. Whether used for school projects, robotics, or microcontroller education, the Cytron Maker UNO Plus ensures a smooth and frustration-free learning experience. Thanks to its pre-labeled pin headers, Micro USB connectivity, and fully Arduino-compatible architecture, setup becomes effortless for new users. Students can instantly code and visualize real-time pin activity through indicator LEDs, making debugging easier and more intuitive. The Cytron Maker UNO Plus is ideal for classroom teaching, STEM labs, maker workshops, and hobby projects, helping learners jump straight into creating fun electronics projects like light sequences, melodies, and interactive displays. Features: Fully compatible with Arduino ecosystem, sharing all libraries and example codes. Integrated 12× onboard LEDs for simplified debugging and visual learning. Built-in piezo buzzer and programmable pushbutton for interactive projects without extra wiring. Upgraded 3.3V line provides 500mA output to support more sensors and modules. Micro USB interface replaces bulky USB Type-B for universal connectivity. Uses FT231X USB-to-Serial converter for easier and more reliable driver installation. Includes pin-header label stickers for effortless classroom identification. CE, FCC & RoHS compliant - safe, environmentally friendly, and education-ready. Students can write their names directly on the board to avoid mix-ups.