Arduino UNO Sensor Shield Expansion board V5

Female to Female Jumper Wires (20cm) 40pcs These are 20cm 40pcs Female to Female Jumper wires, very Flexible and easily detachable. These jumper cables have 1Pin female to the 1pin female header with both ends. Also, it is compatible with 2.54 mm mil spacing pin headers. This cable is an electrical wire or group of them in a cable with a connector or pins at each end, which is normally for interconnecting the components of a breadboard or other prototype or test circuit, internally or with other equipment or components, without soldering. Individual Dupont Cables are fitted by inserting their end connectors into the slots provided in a breadboard, the header connector of a circuit board, or a piece of test equipment. Mostly Dupont cables are useful with Orange Pi, Banana Pi, Raspberry Pi , Arduino , and other mini PCs and development boards . It is very useful in the PCB project, PC motherboard, as well as Breadboard connections. Additionally, these jumper wires allows you to plug and unplug easily for prototyping and can be used over and over again. Check out the best selection of Jumper Wires . Applications: Raspberry Pi Arduino PCB projects Breadboard connections Get a complete set of M2M, M2F, F2F Jumper Wires Set for DIY projects.

A3967 Stepper Motor Driver This A3967 Stepper Motor Driver For Arduino is the most recent version of EasyDriver v44, which was created in collaboration with Brian Schmalz. When compared to previous versions, it offers more flexibility and control over your stepper motor . It is a simple stepper motor driver that is compatible with most microcontrollers and capable of producing a digital 0 to 5V pulse (0 to 3.3V pulse if you solder SJ2 closed on the EasyDriver). A 7V to 30V power supply is required for the module's motor. The digital interface is powered by an onboard voltage regulator that can be set to 5V or 3.3V. The A3967 is a full-featured microstepping motor driver with an integrated transistor. It is intended for use with bipolar stepper motors in full-, half-, quarter-, and eighth-step modes, with output drive capabilities of 30 V and 750 mA. The A3967 comes with a fixed off-time current regulator that can operate in slow, fast, or mixed current-decay modes. This current-decay control scheme produces less audible motor noise, higher step accuracy, and lower power dissipation. The transistor is essential to the A3967's simple implementation. Simply sending one pulse to the STEP input causes the motor to move one step (full, half, quarter, or eighth depending on two logic inputs). It is not necessary to programme phase-sequence tables, high-frequency control lines, or complex interfaces. The A3967 interface is ideal for applications where a complex P is either unavailable or overburdened. Features: A3967 microstepping driver Adjustable current control from 150mA/phase to 750mA/phase MS1 and MS2 pins are broken out to change microstepping resolution to full, half, quarter and eighth steps (defaults to eighth) Compatible with 4, 6, and 8-wire stepper motors of any voltage Breadboard-compatible pins.

CNC Shield for Arduino The CNC shield for Arduino has total four slots, can drive 4 A4988 stepper motors. Each road stepper motors only need two IO ports. In other words, six IO ports can be well managed three stepper motors. The CNC Shield V3.0 allows you to build a engraving machine, 3D printer, mini CNC and other similar devices using your Arduino. It is designed as a shield and can plug on top of an Arduino requiring no external connections and wiring. There are 4 slots on the board for plugging in stepper motor drive module which can drive 1 stepper motor each. Controlling each step stepper motor requires only two IO pins on the Arduino. Just insert this Arduino CNC Shield V3.0 onto an Arduino UNO , and install the GRBL firmware, you can then quickly build a DIY CNC engraving machine. This arduino shield is very convenient to use and is suitable for development boards compatible with Arduino. This CNC shield compatible with Arduino is the latest version of the CN shield model (V 3.0). The CNC Shield is GRBL 0.9 compatible and with the help of jumper wires , it is accessible to stepper drivers. Features: Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place. GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals) 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)

CNC Shield + UNO R3 Board compatible with Arduino + 4xDRV8825 Driver Kit Arduino Uno is an open-source microcontroller used by students and hobbyists entering the world of DIY electronics and automation, The Arduino Uno can be used for any application including being the brains of your next DIY 3D printer and/or CNC router The CNC Shield V3.0 allows you to build an engraving machine, 3D printer, mini CNC and other similar devices using your Arduino. It is designed as a shield and can plug on top of an Arduino requiring no external connections and wiring. Along with that, the CNC shield allows you to control up to four stepper motors by mounting on 4 stepper motor drivers, included with this kit The DRV8825 provides an integrated motor driver solution for printers, scanners, and other automated equipment. The device has two H-bridge and is intended to drive a bipolar stepper motor. Features: UNO R3 Board: The main microcontroller board compatible with Arduino. CNC Shield: An expansion board that allows for easy connection and control of stepper motors. 4x DRV8825 Stepper Motor Drivers: High-performance drivers for controlling stepper motors. Micro-Stepping: Supports micro-stepping settings for precise control of stepper motors. GRBL Compatibility: Compatible with GRBL firmware, which is widely used for CNC control. Voltage Range: Operates on 12-36V DC. Heat Sinks: Included for cooling the stepper motor drivers. USB Cable: For connecting the UNO R3 board to a computer. 40-Pin Row Needles: For additional connections. Applications: CNC Machines: Used for controlling stepper motors in CNC milling, engraving, and cutting machines. 3D Printers: Essential for driving stepper motors in 3D printers, ensuring precise layer deposition and movement. Laser Cutters: Controls stepper motors in laser cutting machines for accurate cutting and engraving. Robotics: Ideal for robotics projects requiring precise motor control, such as robotic arms and automated guided vehicles (AGVs). X-Y Tables: Used in X-Y tables for accurate positioning and movement in various industrial applications. Pick-and-Place Devices: Employed in pick-and-place machines for accurate component placement in electronics manufacturing. Labeling Machines: Used in labeling machines for precise label application. Pinout Diagram for the Arduino Uno Microcontroller Applications of the Kit The kit can be used to create custom 3D printers, scanner, CNC mills and other automated equipment applications

7Semi DS18B20 2M Cable Waterproof Digital Temperature Probe The 7Semi DS18B20 2M Cable Waterproof Digital Temperature Probe is built for anyone who needs precise and stable temperature monitoring in challenging environments. With its stainless-steel sealed casing and durable 2-meter cable, this sensor delivers highly accurate readings, even when fully submerged or installed in remote locations. Whether you're monitoring aquaponics systems, greenhouse conditions, or industrial temperature processes, this digital probe ensures you get consistent and reliable data every single time. Designed with a simple 1-Wire digital interface, the DS18B20 works seamlessly with Arduino, Raspberry Pi, ESP boards, and other microcontrollers, making it ideal for hobbyists, engineers, and automation enthusiasts. Its long cable, waterproof build, and wide temperature range make it a versatile choice for environmental monitoring and precision-driven applications where stability and robustness matter the most. Features: Measures temperatures from –55°C to +125°C, making it suitable for industrial, environmental, and underwater applications. Provides ±0.5°C accuracy, ensuring stable and trustworthy readings. Fully waterproof stainless-steel enclosure protects against moisture, corrosion, and rugged terrain. Comes with a 2-meter high-strength cable to support remote, underwater, or difficult-to-access installations. Supports 9–12 bit resolution and easily integrates using its 3-wire connection and 1-Wire digital protocol.

7Semi MMC5983MA 3-axis Mini Magnetometer Sensor Breakout Module The 7Semi MMC5983MA 3-axis Mini Magnetometer Sensor Breakout Module is a high-precision magnetic sensor designed to measure magnetic fields along three axes with excellent accuracy and stability. It supports a magnetic field range of ±8 Gauss, delivering ultra-low noise and high-resolution output for reliable data. Communicating through a standard I2C interface, this magnetometer sensor ensures low power operation and fast response, making it ideal for navigation systems, orientation tracking, digital compasses, and magnetic anomaly detection. Its compact form factor allows seamless integration into space-constrained electronics, IoT devices, and embedded applications where precise magnetic sensing is essential. Features: Triple-Axis Magnetic Sensing provides great precision across three axes, with 0.4mG resolution and ±0.5° heading accuracy. High Dynamic Range and Resolution: ±8G FSR, 18-bit operation for precise measurements. Built-in Degaussing Circuitry: Effectively eliminates residual magnetization, ensuring consistent performance even when exposed to high external magnetic fields. Advanced Compensation Features: On-chip sensitivity and temperature compensation ensure consistent readings under changing situations. Fast I2C Communication: The I2C protocol has a fast mode of up to 400KHz, allowing for easy integration with other devices. The energy-efficient design consumes only 1µA during power down, making it excellent for power-sensitive applications. Compact form factor: A small PCB layout with a horizontal 4-pin 2mm pitch JST connection, ideal for space-constrained applications.

Cytron UNO Special Edition – Arduino-Compatible Board with Side Connectors The Cytron UNO Special Edition (CT-UNO-SE) is a fully Arduino-compatible development board designed for makers, students, and hobbyists who need reliable performance for DIY electronics and robotics projects. Built around the ATmega328P microcontroller, this board offers the familiar Arduino UNO experience while adding enhanced stability with the FTDI FT231X USB-to-Serial chip, ensuring smoother programming and communication. Whether you're prototyping sensors, robotics circuits, or automation systems, this board delivers a dependable and beginner-friendly platform for all your microcontroller learning needs. What makes the CT-UNO-SE stand out is its unique side connectors, allowing it to be stacked on top of or beneath Arduino shields, giving you maximum flexibility while building layered circuits or compact embedded systems. With full Arduino UNO R3 shield compatibility, 14 digital I/O pins, 6 analog inputs, and both 5V and 3.3V regulated outputs, this special edition board combines convenience, versatility, and long-term durability - all wrapped into a sleek white PCB that makes your projects look clean and professional. Features Built with the ATmega328P microcontroller paired with the Optiboot bootloader for faster program uploads. Equipped with the FTDI FT231X USB interface, offering stable and reliable serial communication. Supports a wide DC input range of 7–15V, suitable for most maker power setups. Includes a 1A 5V regulator and 500mA 3.3V regulator for powering sensors and modules. Offers 14 digital I/O pins (6 PWM) and 6 analog inputs for versatile interfacing. Fully R3 shield compatible with special side connectors for flexible stacking. Features 32KB Flash memory, 2KB SRAM, and 1KB EEPROM for program storage. Comes with easily visible TX, RX, power, and pin-13 LEDs placed on the board edge. Utilizes a durable USB Micro-B connector on a clean white PCB. Dimensions

SmartElex 12V 20A Single Channel Power Relay Module The SmartElex 12V 20A Single Channel Power Relay Module is a high-current switching solution designed to control heavy electrical loads using low-voltage control signals. It helps safely operate high-power devices without directly exposing microcontrollers or control circuits to high current, reducing risk and improving system reliability. This module is suitable for students, makers, engineers, educators, and startups who are working on power control, automation, or embedded electronics projects that demand robust switching capability. This single channel power relay module is ideal for robotics, IoT systems, home and industrial automation, and power management applications where devices such as motors, heaters, pumps, or high-load appliances need reliable control. It can be easily interfaced with popular platforms like Arduino, Raspberry Pi, and ESP32, making it convenient for both prototyping and deployment. The strong build quality and straightforward integration make it a dependable choice for projects requiring consistent and safe high-current switching. Features: Single channel power relay module for high-current load control Operates on 12V, suitable for industrial and automation systems Supports heavy load switching up to 20A Electrical isolation between control and power circuits for safety Compatible with Arduino, Raspberry Pi, ESP32, and similar controllers Robust design for reliable operation in power control applications

SmartElex 5V 3A 8 Channel Signal Relay Module The SmartElex 5V 3A 8 Channel Signal Relay Module is a dependable switching solution built to control multiple electrical devices with precision. This 8 Channel Relay Module features eight JY4100F-S-DC5V-C relays, each capable of safely switching loads up to 3A at 120V AC or 24V DC. Designed to operate on a stable 5V supply, it offers individual input triggers and LED indicators for real-time status visibility. With strong electrical isolation and seamless compatibility with Arduino, ESP32, and Raspberry Pi, this 5V relay module is well-suited for automation panels, IoT systems, and complex control applications where reliable multi-channel switching is essential. Applications: Smart home automation (e.g., managing several appliances) Complex industrial automation systems. Robotics projects require several actuators. IoT systems have several relay outputs. Alarms, security, and access control panels Cautions: Use a well regulated 5V supply with adequate current (at least 1A suggested). Ensure that relay load restrictions are not exceeded. To avoid electrical dangers, securely isolate all AC wiring. Maintain a dry, clean, and dust-free atmosphere. Features: An 8-channel relay module with individual control. It operates at 5V DC and has active LOW/HIGH triggers. Each relay can handle 3A at 120V AC or 24V DC. Compatible with Arduino, ESP32, Raspberry Pi, and more platforms. Status LEDs for each channel are used to monitor operation. Fast switching: ≤10 ms operation and ≤5 ms release. Contact resistance of ≤100 mΩ enables stable conductivity. Total power usage is around 2.88W across all channels. High insulation resistance and dielectric strength are essential for safety. Suitable for -40°C to +85°C temperatures.

SmartElex CP2102 Type C, USB To UART (TTL) Communication Module The SmartElex CP2102 module is a compact and reliable communication module designed to convert USB-C signals into UART (TTL) serial communication. It helps users easily connect microcontrollers and development boards to a computer for programming, debugging, and serial monitoring, removing the need for complex interfaces. This module is well suited for students, makers, educators, engineers, and startups who need a dependable USB to serial solution for everyday electronics work. This USB to UART TTL converter module works smoothly with popular platforms such as Arduino, Raspberry Pi, and ESP32, making it useful for robotics, IoT development, automation systems, and rapid prototyping. Its plug-and-play USB-C design allows quick setup and stable data communication, saving time during development and testing. Whether used for firmware upload, device configuration, or serial communication, this module offers reliable performance and easy integration for practical embedded projects. Applications: Programming and debugging microcontrollers Serial communication with embedded systems USB to TTL conversion for compatible devices Data logging, testing, and monitoring tasks Cautions: Ensure the correct voltage is selected using the onboard jumper to avoid damage Designed only for TTL-level signals; do not connect directly to RS232 interfaces Avoid exposure to moisture and protect the module from static discharge Features: USB-C to UART (TTL) communication module for serial interfacing Based on CP2102 chipset for stable and reliable data transfer Plug-and-play design for quick setup with a computer Compatible with Arduino, Raspberry Pi, ESP32, and similar boards Ideal for programming, debugging, and serial monitoring tasks Suitable for robotics, IoT, automation, and DIY electronics projects

7Semi SGP41 VOC Sensor Breakout Board for Indoor Air Quality Monitoring The 7Semi SGP41 VOC Sensor Breakout Board is a compact and reliable solution for monitoring indoor air quality with high precision. Built around Sensirion’s advanced SGP41 sensing technology, this VOC Sensor accurately detects volatile organic compounds, helping assess air freshness and pollution levels in real time. Operating at an exact 3.3V and communicating via an I2C interface, it integrates smoothly with popular microcontrollers and development boards. The onboard Qwiic connector simplifies wiring, making this air quality VOC sensor ideal for applications such as air purifiers, HVAC systems, smart buildings, and long-term environmental monitoring where accuracy and stability matter. Leverage the power of the SGP41 to create innovative air quality solutions. Whether you're developing air purifiers, ventilation systems, or environmental monitoring devices, this sensor breakout is your essential component. Features: Sensirion SGP40 Sensor: Provides accurate VOC and NOx detection for better air quality assessments. The Digital I2C Interface simplifies communication and integration with your system. Robust Construction: Designed to endure real-world situations while maintaining long-term stability. Compact design is ideal for applications that require limited space. Easy integration: Solderable headers allow for a simple connection.

SmartElex BS612 PIR Motion Sensor Module The SmartElex BS612 PIR Motion Sensor Module is a passive infrared motion detection solution designed to sense human movement by detecting changes in infrared radiation. It helps automate electronic systems by enabling actions only when motion is detected, improving efficiency and reducing unnecessary power usage. This module is suitable for students, makers, engineers, educators, and startups who need a reliable motion sensing component for learning projects, prototypes, and embedded system designs. This PIR motion sensor module is commonly used in robotics, IoT devices, security systems, and home or industrial automation projects where accurate motion detection is required. It can be easily interfaced with popular platforms such as Arduino, Raspberry Pi, and ESP32, allowing quick integration into working systems. The wide detection coverage and stable performance make it ideal for applications like motion-activated lighting, alarm systems, smart monitoring solutions, and interactive electronics projects. Features: Passive infrared (PIR) sensor for accurate human motion detection Detects movement by sensing changes in infrared radiation Wide 120° detection angle for broader area coverage Long sensing range suitable for security and automation use Low power consumption for battery-operated projects Compatible with Arduino, Raspberry Pi, ESP32, and similar microcontrollers

7Semi 5A Analog INA169 DC Current Sensor Breakout The 7Semi 5A Analog INA169 DC Current Sensor Breakout is a precision Analog DC current sensor designed for accurate current monitoring in electronic circuits. Powered by the trusted INA169 chip, it delivers consistent current readings up to 5A across a wide input range of 2.7V to 60V. Its low offset voltage and minimal quiescent current ensure reliable measurements, while adjustable gain and overcurrent protection add versatility for various applications. Compact and easy to integrate with microcontroller-based systems, this INA169 current sensor is perfect for IoT projects, battery management, power monitoring, and smart energy solutions, providing dependable performance for both hobbyists and professional engineers. Features: Wide Voltage Range Compatibility: Operates efficiently between 2.7V and 60V, making it suitable for both low and high-voltage applications. High-Side Current measuring: Enables unipolar high-side current measuring for safer and more accurate readings. Customizable Gain Control: Easily alter output sensitivity with a single resistor to meet your individual application requirements. Built-in Signal Amplifier: Provides clean and amplified output signals for accurate ADC conversion. Overcurrent detection protects connected components by detecting and responding to excessive current. Low Quiescent Current: Consumes only 60 µA, making it ideal for energy-sensitive projects. Microcontroller-Friendly: Fully compatible with Arduino, ESP32, STM32, Raspberry Pi, and other development boards. Compact Design: Small form factor excellent for embedded system integration and space constraints. Connection Diagram with Arduino:

SmartElex Sound Detection Sensor The SmartElex Sound Detection Sensor is a compact and efficient sound sensor module designed to detect sound presence and measure sound intensity with precision. Built around the LM386 audio amplifier, it provides both analog (AOUT) and digital (DOUT) outputs, making it suitable for a wide range of applications—from simple sound-triggered actions to detailed audio level monitoring. Operating smoothly between 3.3V and 5.3V, this sound sensor Arduino compatible module integrates easily with popular development boards such as Arduino, STM32, and Raspberry Pi. Its low power consumption, small form factor, and included 4-pin cable make it perfect for sound-activated projects, noise detection systems, smart devices, and interactive electronics where reliable audio sensing is required. Features: LM386 audio amplifier for a powerful sound signal enhancement. Detect low-level sounds with 200× amplification. Wide voltage range: 3.3 to 5.3 volts Dual outputs: analog (AOUT) and digital (DOUT). Low power consumption, suitable for embedded systems. Adjustable gain using external components Compact and lightweight; breadboard-friendly. Simple integration with Arduino, STM32, and more.

7Semi PCA9306 I2C Bidirectional Voltage Level Translator Breakout Board The 7Semi PCA9306 I2C Bidirectional Voltage Level Translator Breakout Board is a compact and efficient PCA9306 voltage level translator designed to safely interface I2C and SMBus devices operating at different logic levels. Supporting voltage translation from 1.2V to 5.0V, this board enables seamless communication between low-voltage sensors and higher-voltage microcontrollers without manual direction control. As a dependable I2C logic level converter, it delivers minimal signal delay and stable bidirectional data flow, making it ideal for robotics, industrial controllers, embedded systems, and DIY electronics projects requiring precise mixed-voltage I2C communication. Allowable Voltage Level Translation The breakout can transfer voltages ranging from 3.3V to 5V. VREF1 (Low Side) VREF2 (High Side) 1.2V 1.8V, 2.5V, 3.3V, 5V 1.8V 2.5V, 3.3V, 5V 2.5V 3.3V, 5V 3.3V 5V Features: Wide Voltage Range Support: Operates between 1.2V and 5.0V, accommodating a wide range of components. Dual Bidirectional Channels: Translates both the SDA and SCL lines for complete I2C compatibility. I2C and SMBus Protocol Support: Fully compatible with regular and fast-mode I2C devices, as well as SMBus peripherals. No Direction Pins Required: Signal direction is automatically detected for easier design. Low propagation delay: A delay of less than 1.5ns maintains data integrity at high speeds. 5V Tolerant I/O Ports: Securely links 5V signals to lower voltage devices. Compact and simple to use: ideal for embedded applications, prototyping, and compact systems.