Arduino MEGA Prototype Shield V3

Female to Female Jumper Wires (20cm) 40pcs These are 20cm 40pcs Female to Female Jumper wires, very Flexible and easily detachable. These jumper cables have 1Pin female to the 1pin female header with both ends. Also, it is compatible with 2.54 mm mil spacing pin headers. This cable is an electrical wire or group of them in a cable with a connector or pins at each end, which is normally for interconnecting the components of a breadboard or other prototype or test circuit, internally or with other equipment or components, without soldering. Individual Dupont Cables are fitted by inserting their end connectors into the slots provided in a breadboard, the header connector of a circuit board, or a piece of test equipment. Mostly Dupont cables are useful with Orange Pi, Banana Pi, Raspberry Pi , Arduino , and other mini PCs and development boards . It is very useful in the PCB project, PC motherboard, as well as Breadboard connections. Additionally, these jumper wires allows you to plug and unplug easily for prototyping and can be used over and over again. Check out the best selection of Jumper Wires . Applications: Raspberry Pi Arduino PCB projects Breadboard connections Get a complete set of M2M, M2F, F2F Jumper Wires Set for DIY projects.

A3967 Stepper Motor Driver This A3967 Stepper Motor Driver For Arduino is the most recent version of EasyDriver v44, which was created in collaboration with Brian Schmalz. When compared to previous versions, it offers more flexibility and control over your stepper motor . It is a simple stepper motor driver that is compatible with most microcontrollers and capable of producing a digital 0 to 5V pulse (0 to 3.3V pulse if you solder SJ2 closed on the EasyDriver). A 7V to 30V power supply is required for the module's motor. The digital interface is powered by an onboard voltage regulator that can be set to 5V or 3.3V. The A3967 is a full-featured microstepping motor driver with an integrated transistor. It is intended for use with bipolar stepper motors in full-, half-, quarter-, and eighth-step modes, with output drive capabilities of 30 V and 750 mA. The A3967 comes with a fixed off-time current regulator that can operate in slow, fast, or mixed current-decay modes. This current-decay control scheme produces less audible motor noise, higher step accuracy, and lower power dissipation. The transistor is essential to the A3967's simple implementation. Simply sending one pulse to the STEP input causes the motor to move one step (full, half, quarter, or eighth depending on two logic inputs). It is not necessary to programme phase-sequence tables, high-frequency control lines, or complex interfaces. The A3967 interface is ideal for applications where a complex P is either unavailable or overburdened. Features: A3967 microstepping driver Adjustable current control from 150mA/phase to 750mA/phase MS1 and MS2 pins are broken out to change microstepping resolution to full, half, quarter and eighth steps (defaults to eighth) Compatible with 4, 6, and 8-wire stepper motors of any voltage Breadboard-compatible pins.

CNC Shield for Arduino The CNC shield for Arduino has total four slots, can drive 4 A4988 stepper motors. Each road stepper motors only need two IO ports. In other words, six IO ports can be well managed three stepper motors. The CNC Shield V3.0 allows you to build a engraving machine, 3D printer, mini CNC and other similar devices using your Arduino. It is designed as a shield and can plug on top of an Arduino requiring no external connections and wiring. There are 4 slots on the board for plugging in stepper motor drive module which can drive 1 stepper motor each. Controlling each step stepper motor requires only two IO pins on the Arduino. Just insert this Arduino CNC Shield V3.0 onto an Arduino UNO , and install the GRBL firmware, you can then quickly build a DIY CNC engraving machine. This arduino shield is very convenient to use and is suitable for development boards compatible with Arduino. This CNC shield compatible with Arduino is the latest version of the CN shield model (V 3.0). The CNC Shield is GRBL 0.9 compatible and with the help of jumper wires , it is accessible to stepper drivers. Features: Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place. GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals) 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)

CNC Shield + UNO R3 Board compatible with Arduino + 4xDRV8825 Driver Kit Arduino Uno is an open-source microcontroller used by students and hobbyists entering the world of DIY electronics and automation, The Arduino Uno can be used for any application including being the brains of your next DIY 3D printer and/or CNC router The CNC Shield V3.0 allows you to build an engraving machine, 3D printer, mini CNC and other similar devices using your Arduino. It is designed as a shield and can plug on top of an Arduino requiring no external connections and wiring. Along with that, the CNC shield allows you to control up to four stepper motors by mounting on 4 stepper motor drivers, included with this kit The DRV8825 provides an integrated motor driver solution for printers, scanners, and other automated equipment. The device has two H-bridge and is intended to drive a bipolar stepper motor. Features: UNO R3 Board: The main microcontroller board compatible with Arduino. CNC Shield: An expansion board that allows for easy connection and control of stepper motors. 4x DRV8825 Stepper Motor Drivers: High-performance drivers for controlling stepper motors. Micro-Stepping: Supports micro-stepping settings for precise control of stepper motors. GRBL Compatibility: Compatible with GRBL firmware, which is widely used for CNC control. Voltage Range: Operates on 12-36V DC. Heat Sinks: Included for cooling the stepper motor drivers. USB Cable: For connecting the UNO R3 board to a computer. 40-Pin Row Needles: For additional connections. Applications: CNC Machines: Used for controlling stepper motors in CNC milling, engraving, and cutting machines. 3D Printers: Essential for driving stepper motors in 3D printers, ensuring precise layer deposition and movement. Laser Cutters: Controls stepper motors in laser cutting machines for accurate cutting and engraving. Robotics: Ideal for robotics projects requiring precise motor control, such as robotic arms and automated guided vehicles (AGVs). X-Y Tables: Used in X-Y tables for accurate positioning and movement in various industrial applications. Pick-and-Place Devices: Employed in pick-and-place machines for accurate component placement in electronics manufacturing. Labeling Machines: Used in labeling machines for precise label application. Pinout Diagram for the Arduino Uno Microcontroller Applications of the Kit The kit can be used to create custom 3D printers, scanner, CNC mills and other automated equipment applications

SmartElex RedBot - Line Follower Sensor The SmartElex RedBot Line Follower Sensor is an easy-to-use infrared line tracking sensor designed to detect contrasting lines on the floor for robot navigation. It helps users build robots that can follow black or white track lines by sensing reflected infrared light, making it ideal for students, hobbyists, educators, and beginners in robotics. This line follower sensor removes the complexity of designing a tracking circuit from scratch, making it a practical choice for classroom learning, STEM competitions, and project-based exploration. This IR sensor line follower is commonly used in DIY robots, autonomous navigation systems, automation prototypes, and line-following competitions where reliable tracking is essential. It works smoothly with Arduino, Raspberry Pi, ESP32, and other microcontroller platforms, allowing easy integration and quick setup in existing projects. With stable performance and intuitive operation, the SmartElex RedBot Line Follower Sensor is well suited for prototyping, educational labs, and robotics builds requiring precise line tracking and direction control. Features: Infrared-based line detection for accurate track following Detects black or white line contrast for smooth navigation Simple design for beginner-friendly robotics and STEM projects Compatible with Arduino, Raspberry Pi, ESP32, and other controllers Compact module for easy mounting on small robot chassis Ideal for DIY robots, automation prototypes, and line-following competitions

SmartElex USB-C Serial Basic Converter and CH340C IC Breakout Module he SmartElex USB-C Serial Basic Converter with CH340C is a compact USB-to-serial adapter designed to help users program, debug, and communicate with microcontroller boards and embedded systems. It converts USB signals to reliable UART serial communication, making it useful for students, hobbyists, engineers, educators, and startups working with boards that lack native USB support. With its USB-C interface and CH340C chipset, it provides a simple plug-and-play experience for connecting development boards, sensors, and custom circuits to a computer. This USB-to-serial converter is ideal for prototyping in robotics, IoT development, firmware flashing, serial monitoring, and automation projects. It works smoothly with platforms like Arduino, ESP8266, ESP32, Raspberry Pi (UART pins), and other TTL-based microcontrollers, making integration straightforward in both development and testing stages. Offering stable communication and easy computer connectivity, the SmartElex USB-C Serial Basic Converter with CH340C is a practical tool for labs, DIY electronics, and professional development environments. Features: Converts USB-C to TTL serial for programming and debugging CH340C chipset ensures stable and reliable UART communication Plug-and-play design for quick connection to development boards Compatible with Arduino, ESP8266, ESP32, Raspberry Pi (UART), and more Ideal for firmware flashing, serial monitoring, and IoT prototyping Compact breakout module for labs, workshops, and field testing

Cytron CM4 Maker Board for Raspberry Pi The Cytron CM4 Maker Board is a powerful and reliable development board built around the Raspberry Pi Compute Module 4 (CM4), designed specifically for Pro Makers, hardware hobbyists, educators, and embedded developers. With its wide input voltage range, convenient power button, and multiple boot options - including microSD, NVMe SSD, and CM4 eMMC, this Cytron board gives makers complete flexibility in how they build, experiment, and deploy their Raspberry Pi projects. It also retains essential interfaces like Gigabit Ethernet, USB 2.0 ports, HDMI, CSI, and DSI, ensuring compatibility with Raspberry Pi HATs and common accessories. Cytron enhances the standard CM4 experience by adding practical maker-friendly features such as on-board RTC (PCF85063A), Grove ports, Maker Port, 10 GPIO status LEDs, a piezo buzzer with mute switch, and dedicated push buttons. Whether you are creating IoT prototypes, robotics systems, dashboards, or long-running automation projects, the Cytron CM4 Maker Board offers stability, bigger storage options, real-time clock capability, and the expandability required for advanced Raspberry Pi development. Features: The Cytron CM4 Maker Board supports a wide input voltage range through a 7–18V DC jack or 5V USB-C, making it adaptable for various maker setups. Cytron includes a convenient hardware power button, allowing safe shutdown and easy startup without needing terminal commands. The board supports multiple boot sources, including microSD, NVMe SSD (2230/2242), and onboard eMMC on CM4 for faster and more reliable storage. Includes all essential Raspberry Pi features like Gigabit Ethernet, 4× USB 2.0 ports, HDMI, CSI camera port, DSI display port, and 3.5mm audio out. Equipped with PCF85063A RTC, enabling real-time clock functionality even without an internet connection. Cytron adds maker-focused extras such as Grove ports, Maker Port, 10 GPIO LEDs, piezo buzzer, and push buttons for quick prototyping. Pinout Diagram:

SmartElex RJ45 magjack Connector Breakout Board The SmartElex RJ45 MagJack Connector Breakout Board is a convenient module designed to make Ethernet connectivity accessible for custom electronics projects. It breaks out an RJ45 Ethernet jack with integrated magnetics, allowing users to interface network signals with development boards, prototypes, and embedded circuits without needing to design their own connector layout. This board is ideal for students, makers, engineers, educators, and startups who want to experiment with wired networking, communication protocols, or LAN-based control in robotics and IoT applications. This RJ45 MagJack breakout board is commonly used in IoT networks, automation systems, communication modules, and hardware prototypes that require Ethernet access for data transfer or device control. It can be used with platforms like Arduino, Raspberry Pi, ESP32, and other microcontroller boards that support Ethernet interfacing through additional hardware or modules. With reliable connectivity and a beginner-friendly breakout design, the SmartElex RJ45 MagJack Connector Breakout Board is a practical choice for testing, learning, and developing Ethernet-enabled electronic devices and embedded systems. Features: Breaks out an RJ45 MagJack Ethernet connector to easy-to-use pins Simplifies Ethernet interfacing for prototyping and custom circuits Integrated magnetics for stable network signal handling Compatible with Arduino, Raspberry Pi, ESP32 (with Ethernet support) Ideal for IoT, automation, LAN communication, and embedded systems Great for testing, learning, and building Ethernet-enabled devices

SmartElex Multiplexer USB/TTL/RS232/RS485 Communication Converter The SmartElex Multiplexer USB/TTL/RS232/RS485 Communication Converter is a versatile interface board designed to simplify data communication between different serial protocols. It allows users to convert and connect USB signals to TTL, RS232, or RS485 devices without complex wiring or additional hardware, making it ideal for students, makers, engineers, educators, and startups working with industrial equipment, microcontrollers, or legacy communication systems. This module helps bridge communication gaps between computers and embedded hardware, reducing setup time during development and troubleshooting. This multiplexer converter is commonly used in robotics, IoT device management, automation systems, PLC communication, sensor networks, and serial debugging tasks. It works smoothly with Arduino, Raspberry Pi, ESP32, and other microcontroller platforms, enabling stable data exchange and reliable serial protocol conversion for both prototypes and field applications. With easy integration and dependable performance, the SmartElex USB/TTL/RS232/RS485 converter is a practical tool for laboratories, development environments, and industrial interfacing projects that require seamless multi-protocol communication. Features: Supports USB to TTL, RS232, and RS485 serial communication Enables multiple protocol conversions in a single module Simplifies interfacing between computers and embedded systems Compatible with Arduino, Raspberry Pi, ESP32, PLCs, and sensors Ideal for robotics, IoT, automation, and industrial applications Suitable for debugging, monitoring, and data communication testing

SmartElex LIS3DH Triple Axis Accelerometer Breakout The SmartElex LIS3DH Triple Axis Accelerometer Breakout is a compact motion sensor module designed to measure acceleration along the X, Y, and Z axes. It helps users detect tilt, vibration, movement, and orientation, making it ideal for students, makers, educators, and engineers working on motion-responsive electronics. This lis3dh accelerometer offers a beginner-friendly way to collect movement data without complex circuitry, allowing users to focus on learning, building prototypes, or integrating sensors into real-world applications. This 3-axis accelerometer sensor is commonly used in robotics, handheld electronics, IoT devices, gesture recognition systems, and automation projects that require accurate motion sensing. It integrates smoothly with Arduino, Raspberry Pi, ESP32, and other microcontroller platforms, making programming and hardware connections straightforward. With reliable output and easy compatibility, the SmartElex LIS3DH sensor is a practical choice for prototyping, academic learning, DIY electronic builds, and product development where consistent acceleration measurement is required. Features: Triple-axis accelerometer for detecting movement and orientation Measures acceleration along X, Y, and Z axes with reliable output Compact breakout board for easy integration in embedded projects Compatible with Arduino, Raspberry Pi, ESP32, and similar platforms Ideal for robotics, IoT devices, gesture control, and automation projects Great for prototyping, STEM education, and motion-based product development

SmartElex 12V 7A Single Channel Power Relay Module The SmartElex 12V 7A Single Channel Power Relay Module is a dependable switching solution designed to control higher-power electrical loads using low-voltage control signals. It helps protect microcontrollers and sensitive electronics by providing proper isolation between the control circuit and the load side. This module is suitable for students, makers, engineers, educators, and startups who are working on control systems, automation projects, or embedded applications that require safe and reliable power switching. This single channel power relay module is ideal for robotics, IoT systems, home automation, and industrial control projects where devices such as motors, lights, pumps, or other electrical equipment need to be switched reliably. It can be easily interfaced with popular development platforms like Arduino, Raspberry Pi, and ESP32, making it convenient for both prototyping and final product integration. The simple design and consistent performance allow users to build stable control systems without added complexity. Features: Single channel power relay module for high-load switching Operates on 12V, suitable for automation and control systems Supports up to 7A load current for power applications Electrical isolation between control side and load side for safety Compatible with Arduino, Raspberry Pi, ESP32, and similar boards Compact and durable design for easy integration into projects

SmartElex PCA9546 4-Channel I2C Multiplexer Compatible with TCA9546A SmartElex PCA9546 4-Channel I2C Multiplexer is designed to simplify communication management when working with multiple I2C devices that share the same address. This compact module helps prevent signal conflicts by allowing users to connect and control up to four separate I2C buses from a single master device. It’s an ideal solution for students, makers, engineers, educators, and startups who are building projects where multiple sensors or modules need to coexist without addressing limitations or communication errors. Compatible with popular development platforms like Arduino, Raspberry Pi, and ESP32, this PCA9546 I2C multiplexer works as a practical I2C bus expander for robotics, IoT systems, automation projects, and prototype development. It offers a stable, plug-and-play approach to expanding I2C networks, making it easy to integrate sensors, displays, and controllers into both simple and advanced builds. Whether you are creating a multi-sensor environment, debugging complex circuits, or scaling an existing project, this module provides clear routing and dependable performance to streamline development. Features: Enables connection of up to four independent I2C device channels Prevents address conflicts by isolating I2C buses when needed Based on PCA9546 IC and compatible with TCA9546A devices Ideal for expanding I2C networks in multi-sensor projects Works with Arduino, Raspberry Pi, ESP32, and similar controllers Simple control through I2C commands for channel selection

SmartElex AM312 PIR Motion Sensor The SmartElex AM312 PIR Motion Sensor is a compact passive infrared sensor designed to detect human motion by sensing changes in infrared radiation. It helps automate systems by triggering actions only when movement is detected, making projects more energy efficient and responsive. This sensor is well suited for students, makers, engineers, educators, and startups who are working on electronics projects that require reliable motion detection in a small, low-power form factor. This PIR motion sensor is ideal for robotics, IoT devices, security systems, and automation projects, especially where battery-powered operation is important. It can be easily interfaced with popular development platforms such as Arduino, Raspberry Pi, and ESP32, allowing quick integration into prototypes and functional systems. Common applications include motion-activated lighting, smart alarms, occupancy detection, and low-power IoT monitoring solutions, where stable performance and simple integration are essential. Features: Compact PIR sensor for reliable human motion detection Detects movement using changes in infrared radiation Ultra-low power consumption suitable for battery-powered projects Digital output for easy interfacing with microcontrollers Fast response time for real-time motion detection Compatible with Arduino, Raspberry Pi, ESP32, and similar boards

SmartElex HTU21D-F Temperature and Humidity Sensor with Breakout Board The SmartElex HTU21D-F Temperature and Humidity Sensor with Breakout Board is a compact and reliable temperature and humidity sensor designed for accurate environmental monitoring. It helps users measure ambient temperature and humidity digitally with stable output, making it suitable for students, makers, educators, and engineers working on sensing and monitoring applications. This digital temperature and humidity sensor is ideal for those who want dependable readings without complex circuitry, especially in learning, testing, and early product development environments. This I2C digital humidity sensor is widely used in IoT systems, weather monitoring projects, automation setups, and data logging applications where consistent environmental data is required. It integrates easily with popular development platforms such as Arduino, Raspberry Pi, and ESP32, allowing quick setup and smooth communication through the I2C interface. With its breakout board design and reliable performance, the SmartElex HTU21D-F sensor is well suited for prototyping, robotics projects, and educational labs looking for a practical alternative to traditional sensors like SHT15 breakout boards. Features: Digital temperature and humidity sensor with stable and accurate readings I2C interface for simple and reliable data communication Compact breakout board for quick prototyping and testing Easy to use with Arduino, Raspberry Pi, and ESP32 platforms Suitable for IoT, automation, and environmental monitoring projects Ideal replacement option for older sensors like SHT15 breakout boards

SmartElex Tracker Sensor The SmartElex Tracker Sensor is a 5-channel analog IR sensor designed for reliable and accurate line detection in robotics applications. Unlike basic digital sensors, this line tracking sensor delivers precise analog values from all five channels, allowing smoother movement and better control in line-following robots. It works by measuring infrared reflectance, where white surfaces reflect more IR light and black lines absorb it, producing clear output differences. With a 1 cm to 5 cm sensing range, 16 mm sensor spacing, and 3.3V–5V operating voltage, this Tracker Sensor integrates seamlessly with Arduino, Raspberry Pi, and other microcontrollers, making it perfect for educational, DIY, and competitive robotics projects. Features: Five analog output channels allow for precise tracking. Infrared reflectance-based sensing. Improved accuracy compared to digital-only sensors. Detects white and black surfaces that change values. Detection range: 1cm-5cm Detector space: 16mm Compatible with 3.3V to 5V systems. Perfect for robotics and automation tasks.