Arduino LCD TFT01 Shield for Mega Board compatible

Female to Female Jumper Wires (20cm) 40pcs These are 20cm 40pcs Female to Female Jumper wires, very Flexible and easily detachable. These jumper cables have 1Pin female to the 1pin female header with both ends. Also, it is compatible with 2.54 mm mil spacing pin headers. This cable is an electrical wire or group of them in a cable with a connector or pins at each end, which is normally for interconnecting the components of a breadboard or other prototype or test circuit, internally or with other equipment or components, without soldering. Individual Dupont Cables are fitted by inserting their end connectors into the slots provided in a breadboard, the header connector of a circuit board, or a piece of test equipment. Mostly Dupont cables are useful with Orange Pi, Banana Pi, Raspberry Pi , Arduino , and other mini PCs and development boards . It is very useful in the PCB project, PC motherboard, as well as Breadboard connections. Additionally, these jumper wires allows you to plug and unplug easily for prototyping and can be used over and over again. Check out the best selection of Jumper Wires . Applications: Raspberry Pi Arduino PCB projects Breadboard connections Get a complete set of M2M, M2F, F2F Jumper Wires Set for DIY projects.

A3967 Stepper Motor Driver This A3967 Stepper Motor Driver For Arduino is the most recent version of EasyDriver v44, which was created in collaboration with Brian Schmalz. When compared to previous versions, it offers more flexibility and control over your stepper motor . It is a simple stepper motor driver that is compatible with most microcontrollers and capable of producing a digital 0 to 5V pulse (0 to 3.3V pulse if you solder SJ2 closed on the EasyDriver). A 7V to 30V power supply is required for the module's motor. The digital interface is powered by an onboard voltage regulator that can be set to 5V or 3.3V. The A3967 is a full-featured microstepping motor driver with an integrated transistor. It is intended for use with bipolar stepper motors in full-, half-, quarter-, and eighth-step modes, with output drive capabilities of 30 V and 750 mA. The A3967 comes with a fixed off-time current regulator that can operate in slow, fast, or mixed current-decay modes. This current-decay control scheme produces less audible motor noise, higher step accuracy, and lower power dissipation. The transistor is essential to the A3967's simple implementation. Simply sending one pulse to the STEP input causes the motor to move one step (full, half, quarter, or eighth depending on two logic inputs). It is not necessary to programme phase-sequence tables, high-frequency control lines, or complex interfaces. The A3967 interface is ideal for applications where a complex P is either unavailable or overburdened. Features: A3967 microstepping driver Adjustable current control from 150mA/phase to 750mA/phase MS1 and MS2 pins are broken out to change microstepping resolution to full, half, quarter and eighth steps (defaults to eighth) Compatible with 4, 6, and 8-wire stepper motors of any voltage Breadboard-compatible pins.

CNC Shield for Arduino The CNC shield for Arduino has total four slots, can drive 4 A4988 stepper motors. Each road stepper motors only need two IO ports. In other words, six IO ports can be well managed three stepper motors. The CNC Shield V3.0 allows you to build a engraving machine, 3D printer, mini CNC and other similar devices using your Arduino. It is designed as a shield and can plug on top of an Arduino requiring no external connections and wiring. There are 4 slots on the board for plugging in stepper motor drive module which can drive 1 stepper motor each. Controlling each step stepper motor requires only two IO pins on the Arduino. Just insert this Arduino CNC Shield V3.0 onto an Arduino UNO , and install the GRBL firmware, you can then quickly build a DIY CNC engraving machine. This arduino shield is very convenient to use and is suitable for development boards compatible with Arduino. This CNC shield compatible with Arduino is the latest version of the CN shield model (V 3.0). The CNC Shield is GRBL 0.9 compatible and with the help of jumper wires , it is accessible to stepper drivers. Features: Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place. GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals) 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)

CNC Shield + UNO R3 Board compatible with Arduino + 4xDRV8825 Driver Kit Arduino Uno is an open-source microcontroller used by students and hobbyists entering the world of DIY electronics and automation, The Arduino Uno can be used for any application including being the brains of your next DIY 3D printer and/or CNC router The CNC Shield V3.0 allows you to build an engraving machine, 3D printer, mini CNC and other similar devices using your Arduino. It is designed as a shield and can plug on top of an Arduino requiring no external connections and wiring. Along with that, the CNC shield allows you to control up to four stepper motors by mounting on 4 stepper motor drivers, included with this kit The DRV8825 provides an integrated motor driver solution for printers, scanners, and other automated equipment. The device has two H-bridge and is intended to drive a bipolar stepper motor. Features: UNO R3 Board: The main microcontroller board compatible with Arduino. CNC Shield: An expansion board that allows for easy connection and control of stepper motors. 4x DRV8825 Stepper Motor Drivers: High-performance drivers for controlling stepper motors. Micro-Stepping: Supports micro-stepping settings for precise control of stepper motors. GRBL Compatibility: Compatible with GRBL firmware, which is widely used for CNC control. Voltage Range: Operates on 12-36V DC. Heat Sinks: Included for cooling the stepper motor drivers. USB Cable: For connecting the UNO R3 board to a computer. 40-Pin Row Needles: For additional connections. Applications: CNC Machines: Used for controlling stepper motors in CNC milling, engraving, and cutting machines. 3D Printers: Essential for driving stepper motors in 3D printers, ensuring precise layer deposition and movement. Laser Cutters: Controls stepper motors in laser cutting machines for accurate cutting and engraving. Robotics: Ideal for robotics projects requiring precise motor control, such as robotic arms and automated guided vehicles (AGVs). X-Y Tables: Used in X-Y tables for accurate positioning and movement in various industrial applications. Pick-and-Place Devices: Employed in pick-and-place machines for accurate component placement in electronics manufacturing. Labeling Machines: Used in labeling machines for precise label application. Pinout Diagram for the Arduino Uno Microcontroller Applications of the Kit The kit can be used to create custom 3D printers, scanner, CNC mills and other automated equipment applications

3D Printer 128x64 Smart LCD Display Controller for RAMPS 1.4 This smart LCD kit is a 3D printer 128×64 Smart LCD controller for ramps 1.4 and contains the following components: SD-Card reader Rotary encoder 128×64 LCD display You can easily connect it to your Ramps board using the "smart adapter". After connecting this panel to your Ramps you don't need your pc anymore, the Smart Controller supplies power for your SD card. Furthermore, all actions like calibration, axes movements can be done by just using the rotary encoder on the Smart Controller. Print your 3D designs without PC, just with a g-code design stored on the SD card. This panel connects to your RAMPS 1.4 All further operations, such as calibration, the axis movement can be done with the rotary encoder embedded. The SD card slot is integrated at the back so that the files to be printed can be read here. It is used to use since all you need to do is plug and play on the RAMPS. Check out : 1.75mm Luminous White ABS Filament -1Kg

3D Printer - LCD 2004 Graphic Smart Display The intelligent controller includes an sd card reader, rotary encoders and a 20-character — 4 line lcd display. You can easily connect it to your ramps 1. 4 Board using "smart adapter" included. This panel connect your ramps 1. 4, You do not need your computer, your sd card intelligent controller power supply. All further operations, such as calibration, the axis movement can be done only with a rotary encoder intelligent controller. 3D design print without a computer, just use the g code design stored on the sd card.

SmartElex LIS3DH Triple Axis Accelerometer Breakout The SmartElex LIS3DH Triple Axis Accelerometer Breakout is a compact motion sensor module designed to measure acceleration along the X, Y, and Z axes. It helps users detect tilt, vibration, movement, and orientation, making it ideal for students, makers, educators, and engineers working on motion-responsive electronics. This lis3dh accelerometer offers a beginner-friendly way to collect movement data without complex circuitry, allowing users to focus on learning, building prototypes, or integrating sensors into real-world applications. This 3-axis accelerometer sensor is commonly used in robotics, handheld electronics, IoT devices, gesture recognition systems, and automation projects that require accurate motion sensing. It integrates smoothly with Arduino, Raspberry Pi, ESP32, and other microcontroller platforms, making programming and hardware connections straightforward. With reliable output and easy compatibility, the SmartElex LIS3DH sensor is a practical choice for prototyping, academic learning, DIY electronic builds, and product development where consistent acceleration measurement is required. Features: Triple-axis accelerometer for detecting movement and orientation Measures acceleration along X, Y, and Z axes with reliable output Compact breakout board for easy integration in embedded projects Compatible with Arduino, Raspberry Pi, ESP32, and similar platforms Ideal for robotics, IoT devices, gesture control, and automation projects Great for prototyping, STEM education, and motion-based product development

1-Inch LED Digital Display DIY Clock Kit (Blue) – Light-Control MCU Project Set with Casing This DIY LED Digital Clock Kit is an excellent hands-on project for anyone interested in learning how microcontroller-based circuits work. Built around a 51-series MCU, it features a bright 1-inch LED tube display and an automatic light-sensing function that adjusts brightness according to the environment. The kit arrives as individual components, giving learners the opportunity to assemble, solder, and understand every part of the circuit. Created with STEM and STEAM education in mind, this kit helps improve logical thinking, practical assembly skills, and fundamental electronics knowledge. Whether used in a school lab, a maker space, or a home learning setup, it offers a fun and meaningful way to encourage creativity, experimentation, and scientific curiosity. The included housing completes the project with a clean, finished look once assembled. Features: DIY digital clock project featuring a 1-inch LED display for clear time reading. Light-sensing feature ensures suitable brightness in different lighting conditions. Comes as a complete unassembled kit to promote hands-on learning. Strengthens STEM/STEAM concepts such as circuitry, design, and problem-solving. User-friendly build suitable for classrooms, hobbyists, and beginners. Includes a protective enclosure for a neat and durable finish. Includes study instructions to guide the assembly process.

Cytron Maker UNO X – Arduino Compatible Development Board for Classroom The Cytron Maker UNO X is a beginner-friendly, classroom-ready Arduino-compatible development board designed to simplify STEM education. Equipped with built-in LEDs on every digital pin, a programmable push button, a piezo buzzer, and a powerbank-friendly design, it eliminates messy wiring and allows students to start coding instantly. This board is ideal for Arduino beginners, school STEM labs, coding clubs, training centers, and anyone learning microcontroller basics. With plug-and-play functionality and seamless compatibility with Arduino IDE, it delivers a smooth learning experience for educators and students alike. Created with the needs of teachers in mind, the Cytron Maker UNO X features an onboard half-size breadboard and perfboard for quick prototyping, making it easy to build hands-on electronics projects right out of the box. Powered by the ATmega328P, and complete with essential interfaces like UART, SPI, I2C, PWM pins, and analog inputs, this board is perfect for exploring coding, electronics, and robotics in a structured classroom setup. Whether for STEM workshops, school projects, or Arduino training programs, Maker UNO X provides an engaging, frustration-free learning experience. Features: Fully Arduino UNO-compatible board designed specially for classrooms and STEM beginners. Built-in LED indicators on every digital pin, allowing students to visualize code output instantly without wiring. Includes piezo buzzer, programmable push button, and powerbank-friendly operation for portable projects. Comes with an onboard perfboard prototyping area and a half-size breadboard to simplify hands-on experiments. Powered by the reliable ATmega328P microcontroller with 16MHz clock speed and full support in Arduino IDE. Offers 20 digital I/O pins, 6 PWM pins, 6 analog inputs, and communication interfaces (UART, SPI, I2C). Features 32KB Flash, 2KB SRAM, 1KB EEPROM, making it ideal for beginner programming and small-scale electronics projects. Uses a USB Micro-B interface with CH9340 USB-UART chip (note: not supported on Windows 7). Designed by Cytron to support educators - ensures faster learning with fewer wiring issues and more hands-on coding.

SmartElex RJ45 magjack Connector Breakout Board The SmartElex RJ45 MagJack Connector Breakout Board is a convenient module designed to make Ethernet connectivity accessible for custom electronics projects. It breaks out an RJ45 Ethernet jack with integrated magnetics, allowing users to interface network signals with development boards, prototypes, and embedded circuits without needing to design their own connector layout. This board is ideal for students, makers, engineers, educators, and startups who want to experiment with wired networking, communication protocols, or LAN-based control in robotics and IoT applications. This RJ45 MagJack breakout board is commonly used in IoT networks, automation systems, communication modules, and hardware prototypes that require Ethernet access for data transfer or device control. It can be used with platforms like Arduino, Raspberry Pi, ESP32, and other microcontroller boards that support Ethernet interfacing through additional hardware or modules. With reliable connectivity and a beginner-friendly breakout design, the SmartElex RJ45 MagJack Connector Breakout Board is a practical choice for testing, learning, and developing Ethernet-enabled electronic devices and embedded systems. Features: Breaks out an RJ45 MagJack Ethernet connector to easy-to-use pins Simplifies Ethernet interfacing for prototyping and custom circuits Integrated magnetics for stable network signal handling Compatible with Arduino, Raspberry Pi, ESP32 (with Ethernet support) Ideal for IoT, automation, LAN communication, and embedded systems Great for testing, learning, and building Ethernet-enabled devices

SmartElex Atmospheric Sensor Breakout – BME280 Temperature, Humidity & Pressure Sensor Module The SmartElex Atmospheric Sensor Breakout is a compact and reliable module designed to measure temperature, humidity, and air pressure with high accuracy. Built around the powerful BME280 sensor, this 3-in-1 sensor module makes it easy to monitor environmental conditions in real time. Perfect for weather stations, IoT systems, and smart home devices, this environmental sensor breakout delivers precise readings while consuming very little power. It supports both I2C and SPI communication interfaces, making it simple to connect with popular boards like Arduino, ESP32, or Raspberry Pi. Whether you’re building an automation project or a DIY weather monitor, this temperature, humidity, and pressure sensor breakout provides reliable performance and easy integration. It’s a great choice for makers, students, and developers who want accurate environmental data in a small and efficient module. Features: 3-in-1 Environmental Sensor: Accurately measures temperature, humidity, and barometric pressure using the BME280 sensor. High Precision Readings: Provides stable and accurate data for weather monitoring and environmental analysis. I2C & SPI Compatible: This I2C SPI environmental sensor module easily interfaces with Arduino, ESP32, Raspberry Pi, and other microcontrollers. Compact Design: Small and lightweight, making it perfect for embedded systems, IoT devices, and portable applications. Low Power Consumption: Efficient sensor design ensures reliable long-term use in battery-powered projects. Easy to Integrate: Ideal for beginners and professionals working on DIY weather stations, home automation, or environmental monitoring systems.

SmartElex 12V 7A Single Channel Power Relay Module The SmartElex 12V 7A Single Channel Power Relay Module is a dependable switching solution designed to control higher-power electrical loads using low-voltage control signals. It helps protect microcontrollers and sensitive electronics by providing proper isolation between the control circuit and the load side. This module is suitable for students, makers, engineers, educators, and startups who are working on control systems, automation projects, or embedded applications that require safe and reliable power switching. This single channel power relay module is ideal for robotics, IoT systems, home automation, and industrial control projects where devices such as motors, lights, pumps, or other electrical equipment need to be switched reliably. It can be easily interfaced with popular development platforms like Arduino, Raspberry Pi, and ESP32, making it convenient for both prototyping and final product integration. The simple design and consistent performance allow users to build stable control systems without added complexity. Features: Single channel power relay module for high-load switching Operates on 12V, suitable for automation and control systems Supports up to 7A load current for power applications Electrical isolation between control side and load side for safety Compatible with Arduino, Raspberry Pi, ESP32, and similar boards Compact and durable design for easy integration into projects

Cytron Maker Reflect IR Reflectance Sensor for Beginner The Cytron Maker Reflect IR Reflectance Sensor is a compact and beginner-friendly module designed to help learners understand how infrared reflectance works in robotics and automation. Using an IR LED and a high-sensitivity phototransistor, it measures how much IR light bounces back from a surface and generates an analog voltage that’s easy for any microcontroller to read. This makes it perfect for exploring concepts like surface detection, black-and-white line following, and reflectivity measurement. Designed by Cytron with simplicity in mind, this sensor is ideal for kids, students, and makers stepping into DIY robotics projects. Its ultra-small size and centered mounting hole allow it to fit even in tight robot designs, while its 3.3V and 5V compatibility ensures smooth use with Arduino, Raspberry Pi, and all common controllers. Whether you're building a line follower, Sumo bot, maze robot, or encoder-based mechanism, the Maker Reflect delivers reliable IR performance with minimal setup. Features: Works as a hands-on IR reflectance sensor that uses an IR LED + phototransistor to measure surface reflectivity for reliable detection. Helps beginners learn analog sensing, line detection, object presence, and robot navigation, building strong STEM fundamentals. Built with safe, durable Cytron components, ensuring stable performance even in beginner-level DIY robotics projects. Fully compatible with 3.3V and 5V systems, making it easy to interface with Arduino, Raspberry Pi, microcontrollers, and robotics platforms. Offers a sensing distance of 1mm to 40mm at 5V (ideal for black/white surface detection and line following). Provides analog voltage output, allowing smooth interpretation of different surface colors and reflectivity. Compact size of 18.1mm × 8.4mm × 4.2mm, with a centered mounting hole for accurate positioning at the front of robots. Suitable for school projects, robotics clubs, and maker experiments - perfect for line followers, Sumo robots, maze solvers, and encoder wheels. Makes a great STEM learning gift for young robotics enthusiasts and beginners exploring IR sensors.

7Semi SHT40 SGP40 VOC Environmental Monitoring Sensor Module Qwiic-Ready The 7Semi SHT40 + SGP40 VOC Environmental Monitoring Sensor Module is designed to help you measure temperature, humidity, and air quality with high accuracy and minimal effort. Built with advanced SHT40 and SGP40 sensing technology, this compact module delivers precise data for temperature (–40°C to 125°C), humidity (0–100% RH), and VOC levels with excellent response time and reliability. Whether you're prototyping with Arduino, Raspberry Pi, or any I2C-based microcontroller, the Qwiic-compatible interface makes integration incredibly simple and clean. This breakout board is ideal for home automation, indoor air-quality projects, workplace monitoring, or industrial systems where accurate VOC readings matter. Its low power consumption and digital 16-bit output make it highly suitable for long-term IoT deployments, high-precision environmental sensing projects, and portable air-quality monitors. Features: Designed as a compact breakout board integrating the SHT40 high-precision temperature and humidity sensor and the SGP40 VOC sensor for reliable environmental monitoring. Offers fast and accurate measurements, including ±0.2°C temperature accuracy and ±1.8% RH humidity accuracy, ensuring dependable readings in various environments. Qwiic-compatible interface enables effortless plug-and-play connectivity with I2C-enabled microcontrollers and SBCs without soldering. Produces 16-bit digital raw and processed VOC Index signals for easy integration into data-logging, automation, or IoT systems. Ensures low power consumption, making it suitable for battery-powered and continuous-monitoring applications. Built to detect a wide range of volatile organic compounds such as ethanol, acetone, and formaldehyde with high sensitivity and quick response times. Board Dimensions: Arduino I2C Connection Diagram:

Cytron UNO – Arduino UNO Compatible Board with USB Micro-B The Cytron UNO is a fully Arduino UNO compatible development board built with the reliable ATmega328P microcontroller, making it ideal for beginners, students, hobbyists, and electronics enthusiasts. Designed to offer the same functionality as the Arduino UNO R3, the Cytron UNO includes 14 digital I/O pins, 6 PWM outputs, 6 analog inputs, UART, SPI, I2C, and full R3 shield compatibility. With USB Micro-B connectivity, you can easily program the board using the same cable used for Android phones and power banks - making it more convenient and cost-friendly for modern makers. Cytron further enhances the board with a stronger onboard voltage regulator, improved power handling, and repositioned LEDs on the edge for better visibility, even when a shield is attached. The CT-UNO also includes extra standard pads for custom shields, an FTDI-based USB interface for stable programming, and robust DC input support from 7V to 15V. Whether you’re building IoT prototypes, robotics, embedded systems, or learning coding fundamentals, the Cytron UNO delivers reliability, ease of use, and full compatibility with the entire Arduino ecosystem. Features Powered by SMD ATmega328P with Optiboot (UNO R3) bootloader for fast programming. USB programming enabled by stable FTDI FT231X chip for improved reliability. Supports DC 7–15V input with upgraded onboard voltage regulator for higher output current. Offers 14 digital I/O pins, including 6 PWM outputs, and 6 analog inputs for versatile projects. Fully Arduino UNO R3 shield compatible with ISP header and broken-out SDA, SCL, IOREF pins. Uses USB Micro-B socket, compatible with standard Android phone cables. LEDs relocated to board edge for clear visibility during development. Includes additional 2.54mm pads for creating custom shields. White PCB design with clean layout and Cytron build quality. Dimensions