Arduino Data Logger Shield

Female to Female Jumper Wires (20cm) 40pcs These are 20cm 40pcs Female to Female Jumper wires, very Flexible and easily detachable. These jumper cables have 1Pin female to the 1pin female header with both ends. Also, it is compatible with 2.54 mm mil spacing pin headers. This cable is an electrical wire or group of them in a cable with a connector or pins at each end, which is normally for interconnecting the components of a breadboard or other prototype or test circuit, internally or with other equipment or components, without soldering. Individual Dupont Cables are fitted by inserting their end connectors into the slots provided in a breadboard, the header connector of a circuit board, or a piece of test equipment. Mostly Dupont cables are useful with Orange Pi, Banana Pi, Raspberry Pi , Arduino , and other mini PCs and development boards . It is very useful in the PCB project, PC motherboard, as well as Breadboard connections. Additionally, these jumper wires allows you to plug and unplug easily for prototyping and can be used over and over again. Check out the best selection of Jumper Wires . Applications: Raspberry Pi Arduino PCB projects Breadboard connections Get a complete set of M2M, M2F, F2F Jumper Wires Set for DIY projects.

A3967 Stepper Motor Driver This A3967 Stepper Motor Driver For Arduino is the most recent version of EasyDriver v44, which was created in collaboration with Brian Schmalz. When compared to previous versions, it offers more flexibility and control over your stepper motor . It is a simple stepper motor driver that is compatible with most microcontrollers and capable of producing a digital 0 to 5V pulse (0 to 3.3V pulse if you solder SJ2 closed on the EasyDriver). A 7V to 30V power supply is required for the module's motor. The digital interface is powered by an onboard voltage regulator that can be set to 5V or 3.3V. The A3967 is a full-featured microstepping motor driver with an integrated transistor. It is intended for use with bipolar stepper motors in full-, half-, quarter-, and eighth-step modes, with output drive capabilities of 30 V and 750 mA. The A3967 comes with a fixed off-time current regulator that can operate in slow, fast, or mixed current-decay modes. This current-decay control scheme produces less audible motor noise, higher step accuracy, and lower power dissipation. The transistor is essential to the A3967's simple implementation. Simply sending one pulse to the STEP input causes the motor to move one step (full, half, quarter, or eighth depending on two logic inputs). It is not necessary to programme phase-sequence tables, high-frequency control lines, or complex interfaces. The A3967 interface is ideal for applications where a complex P is either unavailable or overburdened. Features: A3967 microstepping driver Adjustable current control from 150mA/phase to 750mA/phase MS1 and MS2 pins are broken out to change microstepping resolution to full, half, quarter and eighth steps (defaults to eighth) Compatible with 4, 6, and 8-wire stepper motors of any voltage Breadboard-compatible pins.

CNC Shield for Arduino The CNC shield for Arduino has total four slots, can drive 4 A4988 stepper motors. Each road stepper motors only need two IO ports. In other words, six IO ports can be well managed three stepper motors. The CNC Shield V3.0 allows you to build a engraving machine, 3D printer, mini CNC and other similar devices using your Arduino. It is designed as a shield and can plug on top of an Arduino requiring no external connections and wiring. There are 4 slots on the board for plugging in stepper motor drive module which can drive 1 stepper motor each. Controlling each step stepper motor requires only two IO pins on the Arduino. Just insert this Arduino CNC Shield V3.0 onto an Arduino UNO , and install the GRBL firmware, you can then quickly build a DIY CNC engraving machine. This arduino shield is very convenient to use and is suitable for development boards compatible with Arduino. This CNC shield compatible with Arduino is the latest version of the CN shield model (V 3.0). The CNC Shield is GRBL 0.9 compatible and with the help of jumper wires , it is accessible to stepper drivers. Features: Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place. GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals) 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)

CNC Shield + UNO R3 Board compatible with Arduino + 4xDRV8825 Driver Kit Arduino Uno is an open-source microcontroller used by students and hobbyists entering the world of DIY electronics and automation, The Arduino Uno can be used for any application including being the brains of your next DIY 3D printer and/or CNC router The CNC Shield V3.0 allows you to build an engraving machine, 3D printer, mini CNC and other similar devices using your Arduino. It is designed as a shield and can plug on top of an Arduino requiring no external connections and wiring. Along with that, the CNC shield allows you to control up to four stepper motors by mounting on 4 stepper motor drivers, included with this kit The DRV8825 provides an integrated motor driver solution for printers, scanners, and other automated equipment. The device has two H-bridge and is intended to drive a bipolar stepper motor. Features: UNO R3 Board: The main microcontroller board compatible with Arduino. CNC Shield: An expansion board that allows for easy connection and control of stepper motors. 4x DRV8825 Stepper Motor Drivers: High-performance drivers for controlling stepper motors. Micro-Stepping: Supports micro-stepping settings for precise control of stepper motors. GRBL Compatibility: Compatible with GRBL firmware, which is widely used for CNC control. Voltage Range: Operates on 12-36V DC. Heat Sinks: Included for cooling the stepper motor drivers. USB Cable: For connecting the UNO R3 board to a computer. 40-Pin Row Needles: For additional connections. Applications: CNC Machines: Used for controlling stepper motors in CNC milling, engraving, and cutting machines. 3D Printers: Essential for driving stepper motors in 3D printers, ensuring precise layer deposition and movement. Laser Cutters: Controls stepper motors in laser cutting machines for accurate cutting and engraving. Robotics: Ideal for robotics projects requiring precise motor control, such as robotic arms and automated guided vehicles (AGVs). X-Y Tables: Used in X-Y tables for accurate positioning and movement in various industrial applications. Pick-and-Place Devices: Employed in pick-and-place machines for accurate component placement in electronics manufacturing. Labeling Machines: Used in labeling machines for precise label application. Pinout Diagram for the Arduino Uno Microcontroller Applications of the Kit The kit can be used to create custom 3D printers, scanner, CNC mills and other automated equipment applications

SmartElex RLS05 Line Follower Sensor The SmartElex RLS05 Line Follower Sensor is a compact and easy-to-use module designed to help robots detect and follow lines on a surface with accuracy. It is ideal for students, makers, educators, and early-stage engineers who are learning robotics or building simple autonomous systems. The sensor simplifies line detection by clearly identifying path contrasts, making it easier to develop reliable line-following behavior without complex circuit design. This sensor is widely used in line follower robots, educational robotics kits, and automation prototypes where precise path tracking is required. It integrates smoothly with popular platforms such as Arduino, Raspberry Pi, and ESP32, allowing quick setup and experimentation. With dependable performance and straightforward interfacing, the SmartElex RLS05 enables users to focus on coding logic and robot movement, making it well suited for classrooms, labs, competitions, and DIY robotics projects in India. Pin Diagram: How to Calibrate SmartElex RLS05 Line Follower Sensor Step 1: Enter Calibration Mode Press the calibration button once or pull the CAL pin low for a few milliseconds. When three LEDs (D0, D2, and D4) turn ON, the module has entered calibration mode. Step 2: White Surface Reading Place the RLS05 module on a white surface and press the calibration button again. When two LEDs (D3 and D4) turn ON, the white surface values are read and saved in EEPROM. Step 3: Black Surface Reading Place the module on a black surface and press the calibration button once more. When three LEDs (D2, D3, and D4) turn ON, the black surface values are read and stored. Step 4: Select Line Following Mode To enable white line following, press the calibration button three times within one second. LEDs (D2, D3, and D4) will blink to confirm selection. To enable black line following, press the calibration button twice. LEDs (D0, D1, and D2) will blink to confirm the mode selection. Features: Five-channel line detection for accurate and stable line following Supports both black line and white line tracking modes One-time calibration with onboard EEPROM memory Easy calibration using onboard push button or CAL pin Compatible with Arduino, Raspberry Pi, and ESP32 platforms Ideal for robotics projects, educational kits, and automation prototypes

SmartElex LHI778 PIR Motion Sensor Module The SmartElex LHI778 PIR Motion Sensor Module is a passive infrared motion detection solution designed to sense human movement by detecting changes in infrared radiation. It helps solve the problem of automatic motion detection without continuous monitoring, making systems more energy efficient and responsive. This module is suitable for students, makers, engineers, educators, and startups working on electronics projects that require reliable motion sensing for control, security, or automation purposes. This PIR motion sensor module is widely used in robotics, IoT devices, security systems, and home or industrial automation projects where movement detection is required. It can be easily interfaced with popular development platforms such as Arduino, Raspberry Pi, and ESP32, allowing quick integration into prototypes and functional systems. The simple interface and consistent performance make it ideal for applications like motion-activated lighting, intrusion detection, smart alarms, and interactive electronic projects. Features: Passive infrared (PIR) sensor for reliable human motion detection Detects movement by sensing changes in infrared radiation Low power operation suitable for battery-powered projects Digital output for easy interfacing with microcontrollers Compatible with Arduino, Raspberry Pi, ESP32, and similar boards Ideal for security systems, automation, and motion-activated applications

SmartElex RJ45 magjack Connector Breakout Board The SmartElex RJ45 MagJack Connector Breakout Board is a convenient module designed to make Ethernet connectivity accessible for custom electronics projects. It breaks out an RJ45 Ethernet jack with integrated magnetics, allowing users to interface network signals with development boards, prototypes, and embedded circuits without needing to design their own connector layout. This board is ideal for students, makers, engineers, educators, and startups who want to experiment with wired networking, communication protocols, or LAN-based control in robotics and IoT applications. This RJ45 MagJack breakout board is commonly used in IoT networks, automation systems, communication modules, and hardware prototypes that require Ethernet access for data transfer or device control. It can be used with platforms like Arduino, Raspberry Pi, ESP32, and other microcontroller boards that support Ethernet interfacing through additional hardware or modules. With reliable connectivity and a beginner-friendly breakout design, the SmartElex RJ45 MagJack Connector Breakout Board is a practical choice for testing, learning, and developing Ethernet-enabled electronic devices and embedded systems. Features: Breaks out an RJ45 MagJack Ethernet connector to easy-to-use pins Simplifies Ethernet interfacing for prototyping and custom circuits Integrated magnetics for stable network signal handling Compatible with Arduino, Raspberry Pi, ESP32 (with Ethernet support) Ideal for IoT, automation, LAN communication, and embedded systems Great for testing, learning, and building Ethernet-enabled devices

7Semi DC-DC Buck Converter 7V-40V Input to 5V 5A Output- AP64500 (BO-10188) The 7Semi DC-DC Buck Converter 7V–40V Input to 5V 5A Output – AP64500 (BO-10188) is a high-power voltage regulator module designed to convert higher DC input voltages into a stable 5V output with up to 5A current. Its wide input range makes it suitable for many power sources, including batteries and industrial supplies, where reliable 5V power is needed. Built around the efficient AP64500 synchronous buck converter, this module delivers stable output with low heat and high efficiency, even under heavy load. It is well suited for powering microcontrollers, single-board computers, sensors, and communication modules. Whether you’re building robotics, automation systems, or advanced electronics projects, this buck converter provides dependable and efficient power management. Features: Wide input voltage range: 7V to 40V DC Stable 5V output with up to 5A continuous current High-efficiency synchronous buck converter using AP64500 Low thermal loss and reliable performance under load Compact breakout module for easy project integration Built-in power protection features for safe operation Ideal for microcontrollers, SBCs, IoT and embedded systems Suitable for robotics, automation, and power supply projects

7Semi SHT40 SGP40 VOC Environmental Monitoring Sensor Module Qwiic-Ready The 7Semi SHT40 + SGP40 VOC Environmental Monitoring Sensor Module is designed to help you measure temperature, humidity, and air quality with high accuracy and minimal effort. Built with advanced SHT40 and SGP40 sensing technology, this compact module delivers precise data for temperature (–40°C to 125°C), humidity (0–100% RH), and VOC levels with excellent response time and reliability. Whether you're prototyping with Arduino, Raspberry Pi, or any I2C-based microcontroller, the Qwiic-compatible interface makes integration incredibly simple and clean. This breakout board is ideal for home automation, indoor air-quality projects, workplace monitoring, or industrial systems where accurate VOC readings matter. Its low power consumption and digital 16-bit output make it highly suitable for long-term IoT deployments, high-precision environmental sensing projects, and portable air-quality monitors. Features: Designed as a compact breakout board integrating the SHT40 high-precision temperature and humidity sensor and the SGP40 VOC sensor for reliable environmental monitoring. Offers fast and accurate measurements, including ±0.2°C temperature accuracy and ±1.8% RH humidity accuracy, ensuring dependable readings in various environments. Qwiic-compatible interface enables effortless plug-and-play connectivity with I2C-enabled microcontrollers and SBCs without soldering. Produces 16-bit digital raw and processed VOC Index signals for easy integration into data-logging, automation, or IoT systems. Ensures low power consumption, making it suitable for battery-powered and continuous-monitoring applications. Built to detect a wide range of volatile organic compounds such as ethanol, acetone, and formaldehyde with high sensitivity and quick response times. Board Dimensions: Arduino I2C Connection Diagram:

SmartElex Atmospheric Sensor Breakout – BME280 Temperature, Humidity & Pressure Sensor Module The SmartElex Atmospheric Sensor Breakout is a compact and reliable module designed to measure temperature, humidity, and air pressure with high accuracy. Built around the powerful BME280 sensor, this 3-in-1 sensor module makes it easy to monitor environmental conditions in real time. Perfect for weather stations, IoT systems, and smart home devices, this environmental sensor breakout delivers precise readings while consuming very little power. It supports both I2C and SPI communication interfaces, making it simple to connect with popular boards like Arduino, ESP32, or Raspberry Pi. Whether you’re building an automation project or a DIY weather monitor, this temperature, humidity, and pressure sensor breakout provides reliable performance and easy integration. It’s a great choice for makers, students, and developers who want accurate environmental data in a small and efficient module. Features: 3-in-1 Environmental Sensor: Accurately measures temperature, humidity, and barometric pressure using the BME280 sensor. High Precision Readings: Provides stable and accurate data for weather monitoring and environmental analysis. I2C & SPI Compatible: This I2C SPI environmental sensor module easily interfaces with Arduino, ESP32, Raspberry Pi, and other microcontrollers. Compact Design: Small and lightweight, making it perfect for embedded systems, IoT devices, and portable applications. Low Power Consumption: Efficient sensor design ensures reliable long-term use in battery-powered projects. Easy to Integrate: Ideal for beginners and professionals working on DIY weather stations, home automation, or environmental monitoring systems.

7Semi SHT41 Temperature & Humidity Sensor Tiny Breakout with I2C Qwiic The 7Semi SHT41 Temperature & Humidity Sensor Tiny Breakout is crafted for engineers, IoT developers, and embedded system designers who need precise environmental monitoring in extremely compact spaces. Powered by the fourth-generation SHT41 sensor, it delivers exceptional accuracy with ±1.8% RH and ±0.2°C precision, making it ideal for sensitive applications like HVAC regulation, smart home devices, and industrial IoT nodes. Its stable readings and fast response time ensure reliable environmental sensing even in dynamic conditions. Designed for low-power performance, this breakout operates on a 3.3V supply and consumes less than 0.15 mA in low-power mode, making it a perfect match for wireless systems and battery-powered deployments. With built-in I2C support, multiple address options, and a compact 1.27 mm pitch connector, integration is quick and hassle-free. Whether you're building connected sensors, indoor air-quality systems, or compact IoT hardware, this module provides dependable data for real-time decision-making and energy-efficient operations. Features: Designed with the advanced SHT41 sensor, offering high-precision measurements with ±1.8% RH humidity accuracy and ±0.2°C temperature accuracy. Operates with ultra-low power consumption, drawing less than 0.15mA in low-power mode to extend battery life in portable systems. Supports I2C communication with multiple configurable addresses for flexible integration in multi-sensor setups. Compact and lightweight form factor with a 1.27 mm pitch 4-pin connector, making it suitable for tight-space and embedded applications. Built for industrial-grade reliability, ensuring consistent performance across typical indoor and light industrial environments. Simple plug-and-play workflow enables quick installation for IoT platforms, smart buildings, automation systems, and environmental monitoring.

SmartElex HTU21D-F Temperature and Humidity Sensor with Breakout Board The SmartElex HTU21D-F Temperature and Humidity Sensor with Breakout Board is a compact and reliable temperature and humidity sensor designed for accurate environmental monitoring. It helps users measure ambient temperature and humidity digitally with stable output, making it suitable for students, makers, educators, and engineers working on sensing and monitoring applications. This digital temperature and humidity sensor is ideal for those who want dependable readings without complex circuitry, especially in learning, testing, and early product development environments. This I2C digital humidity sensor is widely used in IoT systems, weather monitoring projects, automation setups, and data logging applications where consistent environmental data is required. It integrates easily with popular development platforms such as Arduino, Raspberry Pi, and ESP32, allowing quick setup and smooth communication through the I2C interface. With its breakout board design and reliable performance, the SmartElex HTU21D-F sensor is well suited for prototyping, robotics projects, and educational labs looking for a practical alternative to traditional sensors like SHT15 breakout boards. Features: Digital temperature and humidity sensor with stable and accurate readings I2C interface for simple and reliable data communication Compact breakout board for quick prototyping and testing Easy to use with Arduino, Raspberry Pi, and ESP32 platforms Suitable for IoT, automation, and environmental monitoring projects Ideal replacement option for older sensors like SHT15 breakout boards

SmartElex BMM150 3 Axis Magnetometer Sensor The SmartElex BMM150 3 Axis Magnetometer Sensor is a compact digital sensor designed to measure magnetic fields along three axes. It helps users accurately detect orientation and heading, making it useful in projects where direction sensing and magnetic field measurement are required. This sensor is suitable for students, makers, engineers, educators, and startups working on embedded systems, learning projects, and prototype development that need reliable magnetic sensing in a small and easy-to-use form. This 3 axis magnetometer sensor is commonly used in robotics, IoT devices, navigation systems, and automation projects that require compass functionality or motion awareness. It can be easily integrated with popular development platforms such as Arduino, Raspberry Pi, and ESP32, allowing smooth data communication and quick setup. The stable performance and simple interfacing make it ideal for applications like robot navigation, electronic compasses, orientation tracking, and smart sensor-based systems Note - The default configuration of module is I2C interface, for SPI interface remove I2C smd jumper & short SPI smd jumper on module. Features: Measures magnetic field strength along three axes (X, Y, and Z) Enables accurate heading and orientation detection Digital output for easy interfacing with microcontrollers Low power operation suitable for battery-powered projects Compact sensor design for space-constrained applications Compatible with Arduino, Raspberry Pi, ESP32, and other development boards

7Semi MCP9808 I2C Temperature Sensor Breakout The 7Semi MCP9808 I2C Temperature Sensor Breakout is a precision I2C temperature sensor module designed to deliver accurate and reliable temperature measurements with minimal effort. Built around the high-accuracy MCP9808 temperature sensor IC, this breakout board provides easy digital temperature sensing through a standard I2C interface, making it ideal for projects where precise environmental monitoring is essential. It solves the challenge of interfacing analog temperature sensors with microcontrollers by offering a simple digital communication method that eliminates the need for complex calibration. This compact sensor module is highly compatible with popular development platforms like Arduino, Raspberry Pi, and other microcontrollers, offering stable performance and low power consumption. With its high accuracy and straightforward interface, it’s perfect for students, hobbyists, and professionals working on weather stations, HVAC systems, data loggers, thermal control systems, and indoor environmental monitoring projects. Its robust design ensures dependable readings across a wide range of applications, reducing development time and improving overall system reliability. Features: High-accuracy MCP9808 sensor IC with ±0.25 °C typical precision Wide operating temperature range from –40 °C to +125 °C High-resolution temperature readings with 0.0625 °C resolution Supports 2.7V to 5.5V power and logic levels for flexible compatibility I²C interface allows connection of up to 8 sensors on a single bus Compact breakout board for easy integration in embedded projects

7Semi High-Precision Temperature & Humidity Sensor Probe The 7Semi High-Precision One-Wire Temperature and Humidity Probe is engineered for applications where accuracy, durability, and reliability truly matter. Built with advanced CMOSens sensing technology, it delivers precise digital measurements even in extreme environmental conditions. Its stainless-steel porous housing provides excellent protection against moisture, dust, and chemical contaminants, making it dependable for long-term use in demanding setups. Designed for industrial automation, scientific research, HVAC systems, and environmental monitoring, this probe offers excellent responsiveness and stability across wide temperature and humidity ranges. The one-wire interface reduces wiring complexity, while the compact form factor and 1-meter cable make installation effortless. With its industrial-grade sensing, high-accuracy performance, and rugged enclosure, this probe is ideal for both stationary and mobile applications. Features: Designed with advanced CMOSens technology to deliver highly accurate humidity and temperature readings in challenging environments. Operates efficiently at 3.3V, making it suitable for battery-powered and portable devices. Works across extreme environmental conditions, including temperatures from -40°C to +125°C and pressures up to 150 bar. Encased in a stainless-steel breathable shell that resists corrosion, dust, chemical exposure, and moisture. One-wire digital interface ensures simple integration and minimal wiring requirements. Proven reliability in high-pressure, high-temperature, vacuum, and explosive environments. Built for long service life with strong resistance to oxidation and particulate blockage. Includes a 1-meter cable with a mini round shell connector for flexible installation in tight or specialized spaces. 7Semi High-Precision Temperature & Humidity Sensor Probe Pinout Diagram: