ADIY UNO KIT FOR BEGINNERS ( Make in India Boards)

Female to Female Jumper Wires (20cm) 40pcs These are 20cm 40pcs Female to Female Jumper wires, very Flexible and easily detachable. These jumper cables have 1Pin female to the 1pin female header with both ends. Also, it is compatible with 2.54 mm mil spacing pin headers. This cable is an electrical wire or group of them in a cable with a connector or pins at each end, which is normally for interconnecting the components of a breadboard or other prototype or test circuit, internally or with other equipment or components, without soldering. Individual Dupont Cables are fitted by inserting their end connectors into the slots provided in a breadboard, the header connector of a circuit board, or a piece of test equipment. Mostly Dupont cables are useful with Orange Pi, Banana Pi, Raspberry Pi , Arduino , and other mini PCs and development boards . It is very useful in the PCB project, PC motherboard, as well as Breadboard connections. Additionally, these jumper wires allows you to plug and unplug easily for prototyping and can be used over and over again. Check out the best selection of Jumper Wires . Applications: Raspberry Pi Arduino PCB projects Breadboard connections Get a complete set of M2M, M2F, F2F Jumper Wires Set for DIY projects.

A3967 Stepper Motor Driver This A3967 Stepper Motor Driver For Arduino is the most recent version of EasyDriver v44, which was created in collaboration with Brian Schmalz. When compared to previous versions, it offers more flexibility and control over your stepper motor . It is a simple stepper motor driver that is compatible with most microcontrollers and capable of producing a digital 0 to 5V pulse (0 to 3.3V pulse if you solder SJ2 closed on the EasyDriver). A 7V to 30V power supply is required for the module's motor. The digital interface is powered by an onboard voltage regulator that can be set to 5V or 3.3V. The A3967 is a full-featured microstepping motor driver with an integrated transistor. It is intended for use with bipolar stepper motors in full-, half-, quarter-, and eighth-step modes, with output drive capabilities of 30 V and 750 mA. The A3967 comes with a fixed off-time current regulator that can operate in slow, fast, or mixed current-decay modes. This current-decay control scheme produces less audible motor noise, higher step accuracy, and lower power dissipation. The transistor is essential to the A3967's simple implementation. Simply sending one pulse to the STEP input causes the motor to move one step (full, half, quarter, or eighth depending on two logic inputs). It is not necessary to programme phase-sequence tables, high-frequency control lines, or complex interfaces. The A3967 interface is ideal for applications where a complex P is either unavailable or overburdened. Features: A3967 microstepping driver Adjustable current control from 150mA/phase to 750mA/phase MS1 and MS2 pins are broken out to change microstepping resolution to full, half, quarter and eighth steps (defaults to eighth) Compatible with 4, 6, and 8-wire stepper motors of any voltage Breadboard-compatible pins.

CNC Shield for Arduino The CNC shield for Arduino has total four slots, can drive 4 A4988 stepper motors. Each road stepper motors only need two IO ports. In other words, six IO ports can be well managed three stepper motors. The CNC Shield V3.0 allows you to build a engraving machine, 3D printer, mini CNC and other similar devices using your Arduino. It is designed as a shield and can plug on top of an Arduino requiring no external connections and wiring. There are 4 slots on the board for plugging in stepper motor drive module which can drive 1 stepper motor each. Controlling each step stepper motor requires only two IO pins on the Arduino. Just insert this Arduino CNC Shield V3.0 onto an Arduino UNO , and install the GRBL firmware, you can then quickly build a DIY CNC engraving machine. This arduino shield is very convenient to use and is suitable for development boards compatible with Arduino. This CNC shield compatible with Arduino is the latest version of the CN shield model (V 3.0). The CNC Shield is GRBL 0.9 compatible and with the help of jumper wires , it is accessible to stepper drivers. Features: Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place. GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals) 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)

CNC Shield + UNO R3 Board compatible with Arduino + 4xDRV8825 Driver Kit Arduino Uno is an open-source microcontroller used by students and hobbyists entering the world of DIY electronics and automation, The Arduino Uno can be used for any application including being the brains of your next DIY 3D printer and/or CNC router The CNC Shield V3.0 allows you to build an engraving machine, 3D printer, mini CNC and other similar devices using your Arduino. It is designed as a shield and can plug on top of an Arduino requiring no external connections and wiring. Along with that, the CNC shield allows you to control up to four stepper motors by mounting on 4 stepper motor drivers, included with this kit The DRV8825 provides an integrated motor driver solution for printers, scanners, and other automated equipment. The device has two H-bridge and is intended to drive a bipolar stepper motor. Features: UNO R3 Board: The main microcontroller board compatible with Arduino. CNC Shield: An expansion board that allows for easy connection and control of stepper motors. 4x DRV8825 Stepper Motor Drivers: High-performance drivers for controlling stepper motors. Micro-Stepping: Supports micro-stepping settings for precise control of stepper motors. GRBL Compatibility: Compatible with GRBL firmware, which is widely used for CNC control. Voltage Range: Operates on 12-36V DC. Heat Sinks: Included for cooling the stepper motor drivers. USB Cable: For connecting the UNO R3 board to a computer. 40-Pin Row Needles: For additional connections. Applications: CNC Machines: Used for controlling stepper motors in CNC milling, engraving, and cutting machines. 3D Printers: Essential for driving stepper motors in 3D printers, ensuring precise layer deposition and movement. Laser Cutters: Controls stepper motors in laser cutting machines for accurate cutting and engraving. Robotics: Ideal for robotics projects requiring precise motor control, such as robotic arms and automated guided vehicles (AGVs). X-Y Tables: Used in X-Y tables for accurate positioning and movement in various industrial applications. Pick-and-Place Devices: Employed in pick-and-place machines for accurate component placement in electronics manufacturing. Labeling Machines: Used in labeling machines for precise label application. Pinout Diagram for the Arduino Uno Microcontroller Applications of the Kit The kit can be used to create custom 3D printers, scanner, CNC mills and other automated equipment applications

TL-Smoother module for 3D printer motor drivers V1.0 A smoother module for stepper driver motor is an add-on module for stepper motors of 3D Printers. It is useful for a softer movement in Delta Style 3D Printer as when using DVR8825 or step and drives and A4988/2 driver unit. TL smoothers are popular little printed circuit boards (PCBs) that are often used in FDM 3D printers to not surprisingly, smooth out the look of prints. In other words, they reduce surface artifacts caused by irregular stepper motor motion, often dubbed “zebra stripes,” “salmon skin,” etc. These smoothers are often sold as 4- and 8-diode variants, with the 8-diode ones (pictured above) offering a stronger smoothing effect. They plug into any 3D printer between the stepper drivers and the stepper motors, working their electrical “magic” without any other setup needed. Their low cost, plug-and-play functionality, and seemingly magical effect have made them quite beloved, albeit slightly controversial. The board provides flyback diodes (freewheeling diodes) for the motor outputs so that they are also protected against induction voltages in the unpowered state of the driver. You will get smoother movement. Features: Suitable for all FDM types of 3D printers Lower vibration, lower noise, and smoother result. Smoother movement especially on the delta-style 3Dprinter under DVR8825 stepper drivers and A4988/2 drivers.

7Semi BME280 Temperature, Humidity & Pressure Sensor Nano Breakout The 7Semi BME280 Nano Breakout is a compact and highly reliable environmental sensing module designed for projects that require accurate temperature, humidity, and barometric pressure readings. Powered by Bosch’s trusted BME280 sensor, it delivers precise data with ±1.0°C temperature accuracy, ±3% humidity accuracy, and ±1 hPa pressure accuracy. With its 2.54mm pitch header and I2C interface, this breakout integrates effortlessly into Arduino, Raspberry Pi, and other embedded systems, making it perfect for weather stations, smart home setups, and environmental monitoring projects. Its small footprint and robust construction make it suitable for space-constrained applications without compromising performance. Whether you're building a DIY weather dashboard, automating a greenhouse, or working on an IoT environmental sensor node, the BME280 ensures fast, stable, and reliable readings. This sensor is also capable of altitude measurement, bringing added versatility to drones, outdoor devices, and scientific experiments. Features: Provides highly accurate temperature, humidity, and barometric pressure measurements using the Bosch BME280 sensor. Supports I2C communication and operates at 3.3V, ensuring simple wiring and compatibility with common microcontrollers. Compact nano breakout design with a 2.54mm pitch header, making it ideal for breadboard and prototype-friendly builds. Offers dependable performance with ±1.0°C temperature accuracy, ±3% humidity accuracy, and ±1 hPa pressure accuracy. Functions as an altimeter with ±1 meter accuracy, adding enhanced functionality for robotics and outdoor applications. Built with a durable and reliable layout, ensuring long-term stability in environmental and scientific projects. Suitable for weather monitoring, smart home automation, agriculture, greenhouse tracking, and IoT systems.

7Semi DC-DC Buck Converter 14V-60V Input to 5V 3A Output- AP66300 (BO-10189) The 7Semi DC-DC Buck Converter 14V–60V Input to 5V 3A Output – AP66300 (BO-10189) is a compact power module designed to convert high DC input voltages into a stable 5V output with up to 3A current. Its wide input range makes it suitable for applications that use automotive, industrial, or high-voltage power sources. Built on an efficient synchronous buck design, this converter delivers reliable power with low heat generation and minimal energy loss. It is well suited for powering microcontrollers, sensors, communication modules, and other embedded electronics. Whether you’re working on industrial systems, automation projects, or advanced DIY builds, this buck converter provides a dependable and efficient power solution. Features: Wide input range: accepts 14V to 60V DC sources Provides a stable 5V output at up to 3A High-efficiency buck converter design for low energy loss Compact breakout board for easy project use Built-in power protection for safer operation Ideal for automotive, industrial, and embedded electronics Supports powering microcontrollers, sensors, and communication modules Efficient solution for IoT, automation, and high-voltage systems

SCD40 I2C CO Temperature & Humidity Sensor Breakout Module - 7Semi The 7Semi SCD40 is a compact sensor breakout based on Sensirion’s advanced photoacoustic NDIR technology. It accurately measures CO concentration from 400 ppm to 40,000 ppm, along with ambient temperature and humidity. Ideal for air quality monitoring, HVAC systems, and IoT applications. It communicates over the I²C interface and is compatible with most microcontrollers. With low power consumption, long-term stability, and minimal recalibration requirements, the SCD40 is well-suited for portable and embedded systems requiring reliable environmental data. Features Photoacoustic CO Sensing: Uses advanced photoacoustic infrared technology for high-precision CO measurement. 3-in-1 Environmental Monitoring: Simultaneously tracks CO levels, temperature, and humidity for a complete atmospheric overview. Wide CO Detection Range: Measures concentrations from 400 ppm to 40,000 ppm, with optimal accuracy in the 400–2000 ppm range. High Accuracy: Offers a precision of ±(40 ppm + 5%), making it ideal for critical monitoring applications. Low Power Consumption: Consumes only 17 mA at 5s intervals and 0.5 mA at 5-minute intervals, perfect for battery-powered projects. Plug-and-Play Ready: Factory-calibrated and ready for immediate use—no manual calibration required. I2C Interface: Compatible with Arduino, Raspberry Pi, ESP32, STM32, and other popular microcontrollers via I2C. Compact Design: Small, robust module fits easily into embedded systems and space-limited enclosures. SCD40 carbon dioxide sensor Breakout I2C Arduino Connections

7Semi MCP4725 12bit Digital to Analog I2C Breakout Module The 7Semi MCP4725 12bit Digital-to-Analog I2C Breakout Module is a compact and reliable MCP4725 DAC module designed for accurate analog voltage generation in embedded and IoT projects. This single-channel digital-to-analog converter delivers true 12-bit resolution with a buffered rail-to-rail output, ensuring stable and precise voltage control. Operating on a 2.7V to 5.5V supply, it communicates via the I2C interface supporting standard, fast, and high-speed modes up to 3.4 Mbps. With an onboard non-volatile EEPROM, the module retains its last configured output even after power-off, making it ideal for automation systems, signal generation, and microcontroller-based applications where consistent analog output is critical. Features: 12-bit resolution provides high-precision output for precise analog signal representation. On-Board Nonvolatile Memory (EEPROM): Configuration settings are retained even when the power is turned off, ensuring speedy power-up and project continuity. Low power consumption: Ideal for battery-powered applications, which extends device life. I2C Interface: Supports three modes: Standard (100 kbps), Fast (400 kbps), and High-Speed (3.4 Mbps), with eight addresses available for flexible communication. Rail-to-Rail Output: Expands the output voltage range, increasing versatility in a variety of applications. Fast Settling Time: With an average settling time of only 6 µs, you can analyze signals quickly and accurately.

SmartElex 8 Channel Multiplexer Breakout Module – (74HC4051) The SmartElex 8 Channel Multiplexer Breakout Module (74HC4051) is a compact and efficient solution for expanding input and output options in electronic projects. This 74HC4051 multiplexer breakout allows users to route multiple signals through a single microcontroller pin, solving the problem of limited I/O availability when working with sensors, switches, or analog inputs. It is designed for students, makers, engineers, educators, and startups who need a practical way to manage multiple device connections without increasing hardware complexity. This module acts as both an 8 channel multiplexer and demultiplexer, making it suitable for robotics, IoT systems, automation tasks, and rapid prototyping. It integrates smoothly with Arduino, Raspberry Pi, ESP32, and similar platforms, enabling users to scale projects without sacrificing performance or stability. Whether you are building sensor hubs, data acquisition systems, or experimenting with signal routing, this multiplexer demultiplexer module offers a reliable and easy-to-use interface that enhances flexibility in circuit design. Features: Based on the 74HC4051 8-channel analog/digital multiplexer IC Expands I/O by routing up to 8 signals through a single control interface Works as both a multiplexer and demultiplexer for flexible signal routing Helps manage limited microcontroller pins in multi-sensor projects Compatible with Arduino, Raspberry Pi, ESP32, and similar platforms Ideal for robotics, IoT systems, data acquisition, and prototyping

SmartElex AM312 PIR Motion Sensor The SmartElex AM312 PIR Motion Sensor is a compact passive infrared sensor designed to detect human motion by sensing changes in infrared radiation. It helps automate systems by triggering actions only when movement is detected, making projects more energy efficient and responsive. This sensor is well suited for students, makers, engineers, educators, and startups who are working on electronics projects that require reliable motion detection in a small, low-power form factor. This PIR motion sensor is ideal for robotics, IoT devices, security systems, and automation projects, especially where battery-powered operation is important. It can be easily interfaced with popular development platforms such as Arduino, Raspberry Pi, and ESP32, allowing quick integration into prototypes and functional systems. Common applications include motion-activated lighting, smart alarms, occupancy detection, and low-power IoT monitoring solutions, where stable performance and simple integration are essential. Features: Compact PIR sensor for reliable human motion detection Detects movement using changes in infrared radiation Ultra-low power consumption suitable for battery-powered projects Digital output for easy interfacing with microcontrollers Fast response time for real-time motion detection Compatible with Arduino, Raspberry Pi, ESP32, and similar boards

7Semi ENS160 Air Quality Sensor I2C Probe (ES-12183) The 7Semi ENS160 Air Quality Sensor I2C Probe (ES-12183) is a compact and ready-to-use air quality sensing module built to measure indoor environmental conditions. It uses the advanced ENS160 multi-gas sensor to detect volatile organic compounds (VOCs) and other indoor pollutants, helping you understand the quality of the air around you. The probe provides clean, processed digital outputs that make monitoring easy. This sensor communicates over a standard I2C interface and works at 3.3 V, making it simple to connect to popular controllers like Arduino, ESP32, or Raspberry Pi. With features like long-term stability, low power use, and reliable performance across a range of temperatures and humidity levels, it’s a great choice for smart home systems, air purifiers, HVAC monitoring, and other environmental projects. Features: Advanced ENS160 multi-gas sensor for indoor air quality monitoring Detects VOCs and air quality levels for healthier environments I2C digital interface for simple integration with microcontrollers Factory-calibrated sensor for reliable and consistent readings Low power consumption, suitable for continuous monitoring Compatible with Arduino, ESP32, Raspberry Pi, and IoT systems 7Semi I2C Wire Color Code

SmartElex BMM150 3 Axis Magnetometer Sensor The SmartElex BMM150 3 Axis Magnetometer Sensor is a compact digital sensor designed to measure magnetic fields along three axes. It helps users accurately detect orientation and heading, making it useful in projects where direction sensing and magnetic field measurement are required. This sensor is suitable for students, makers, engineers, educators, and startups working on embedded systems, learning projects, and prototype development that need reliable magnetic sensing in a small and easy-to-use form. This 3 axis magnetometer sensor is commonly used in robotics, IoT devices, navigation systems, and automation projects that require compass functionality or motion awareness. It can be easily integrated with popular development platforms such as Arduino, Raspberry Pi, and ESP32, allowing smooth data communication and quick setup. The stable performance and simple interfacing make it ideal for applications like robot navigation, electronic compasses, orientation tracking, and smart sensor-based systems Note - The default configuration of module is I2C interface, for SPI interface remove I2C smd jumper & short SPI smd jumper on module. Features: Measures magnetic field strength along three axes (X, Y, and Z) Enables accurate heading and orientation detection Digital output for easy interfacing with microcontrollers Low power operation suitable for battery-powered projects Compact sensor design for space-constrained applications Compatible with Arduino, Raspberry Pi, ESP32, and other development boards

SmartElex 12V 10A Single Channel Power Relay Module The SmartElex 12V 10A Single Channel Power Relay Module is a reliable switching solution designed to control high-power electrical loads using low-voltage control signals. It helps safely operate devices that draw higher current without directly connecting them to sensitive control circuits. This module is suitable for students, makers, engineers, educators, and startups who are working on electronics projects, automation systems, or prototypes that require dependable and safe power switching. This single channel power relay module is widely used in robotics, IoT applications, home automation, and industrial control projects where motors, lights, pumps, or appliances need to be switched on and off reliably. It can be easily interfaced with popular platforms such as Arduino, Raspberry Pi, and ESP32, making integration simple for both learning projects and real-world systems. The sturdy design and consistent performance make it a practical choice for prototyping as well as final deployment in power control applications. Features: Single channel power relay module for high-current load switching Operates on 12V, suitable for automation and control applications Supports up to 10A load current for power devices Electrical isolation between control and load circuits for safety Compatible with Arduino, Raspberry Pi, ESP32, and similar boards Compact and durable design for easy integration

7Semi High-Precision Temperature & Humidity Sensor Probe The 7Semi High-Precision One-Wire Temperature and Humidity Probe is engineered for applications where accuracy, durability, and reliability truly matter. Built with advanced CMOSens sensing technology, it delivers precise digital measurements even in extreme environmental conditions. Its stainless-steel porous housing provides excellent protection against moisture, dust, and chemical contaminants, making it dependable for long-term use in demanding setups. Designed for industrial automation, scientific research, HVAC systems, and environmental monitoring, this probe offers excellent responsiveness and stability across wide temperature and humidity ranges. The one-wire interface reduces wiring complexity, while the compact form factor and 1-meter cable make installation effortless. With its industrial-grade sensing, high-accuracy performance, and rugged enclosure, this probe is ideal for both stationary and mobile applications. Features: Designed with advanced CMOSens technology to deliver highly accurate humidity and temperature readings in challenging environments. Operates efficiently at 3.3V, making it suitable for battery-powered and portable devices. Works across extreme environmental conditions, including temperatures from -40°C to +125°C and pressures up to 150 bar. Encased in a stainless-steel breathable shell that resists corrosion, dust, chemical exposure, and moisture. One-wire digital interface ensures simple integration and minimal wiring requirements. Proven reliability in high-pressure, high-temperature, vacuum, and explosive environments. Built for long service life with strong resistance to oxidation and particulate blockage. Includes a 1-meter cable with a mini round shell connector for flexible installation in tight or specialized spaces. 7Semi High-Precision Temperature & Humidity Sensor Probe Pinout Diagram: