ACEBOTT QD023 Motion-Sensing Glove with Encoders & Accelerometer & Enhanced ESP32 Controller

Female to Female Jumper Wires (20cm) 40pcs These are 20cm 40pcs Female to Female Jumper wires, very Flexible and easily detachable. These jumper cables have 1Pin female to the 1pin female header with both ends. Also, it is compatible with 2.54 mm mil spacing pin headers. This cable is an electrical wire or group of them in a cable with a connector or pins at each end, which is normally for interconnecting the components of a breadboard or other prototype or test circuit, internally or with other equipment or components, without soldering. Individual Dupont Cables are fitted by inserting their end connectors into the slots provided in a breadboard, the header connector of a circuit board, or a piece of test equipment. Mostly Dupont cables are useful with Orange Pi, Banana Pi, Raspberry Pi , Arduino , and other mini PCs and development boards . It is very useful in the PCB project, PC motherboard, as well as Breadboard connections. Additionally, these jumper wires allows you to plug and unplug easily for prototyping and can be used over and over again. Check out the best selection of Jumper Wires . Applications: Raspberry Pi Arduino PCB projects Breadboard connections Get a complete set of M2M, M2F, F2F Jumper Wires Set for DIY projects.

A3967 Stepper Motor Driver This A3967 Stepper Motor Driver For Arduino is the most recent version of EasyDriver v44, which was created in collaboration with Brian Schmalz. When compared to previous versions, it offers more flexibility and control over your stepper motor . It is a simple stepper motor driver that is compatible with most microcontrollers and capable of producing a digital 0 to 5V pulse (0 to 3.3V pulse if you solder SJ2 closed on the EasyDriver). A 7V to 30V power supply is required for the module's motor. The digital interface is powered by an onboard voltage regulator that can be set to 5V or 3.3V. The A3967 is a full-featured microstepping motor driver with an integrated transistor. It is intended for use with bipolar stepper motors in full-, half-, quarter-, and eighth-step modes, with output drive capabilities of 30 V and 750 mA. The A3967 comes with a fixed off-time current regulator that can operate in slow, fast, or mixed current-decay modes. This current-decay control scheme produces less audible motor noise, higher step accuracy, and lower power dissipation. The transistor is essential to the A3967's simple implementation. Simply sending one pulse to the STEP input causes the motor to move one step (full, half, quarter, or eighth depending on two logic inputs). It is not necessary to programme phase-sequence tables, high-frequency control lines, or complex interfaces. The A3967 interface is ideal for applications where a complex P is either unavailable or overburdened. Features: A3967 microstepping driver Adjustable current control from 150mA/phase to 750mA/phase MS1 and MS2 pins are broken out to change microstepping resolution to full, half, quarter and eighth steps (defaults to eighth) Compatible with 4, 6, and 8-wire stepper motors of any voltage Breadboard-compatible pins.

Official Raspberry Pi 4 Model B 4GB RAM The Raspberry Pi 4 Model B 4GB is a compact and versatile single-board computer that provides desktop-level performance in a credit card-sized device. The RPI 4B is powered by a Broadcom Quad-Core Cortex-A72 (ARM v8) 64-bit SoC that runs at 1.5GHz and has 4GB of LPDDR4-3200 SDRAM for efficient multitasking and basic desktop programs. This device is designed for a wide range of DIY projects, including media centres, file servers, robotics, and smart home systems. The Raspberry Pi 4B 4GB supports dual 4K displays ( 4K@30Hz ) through its micro-HDMI ports, making it perfect for high-definition video and creative endeavours. It has dual-band WiFi 2.4 GHz and 5.0 GHz IEEE 802.11ac , Bluetooth 5.0 , and Gigabit Ethernet for a consistent connection. It also features two USB 3.0 connections and two USB 2.0 ports to connect devices. The Raspberry Pi 4 4GB is popular among programmers and makers. It comes with native Python support , making it a fantastic platform for coding education and automation project development. It is capable of running both 32-bit and 64-bit operating systems , offering versatility for different uses. Whether for teaching, prototyping, or creative projects, it serves as a potent and affordable computing option. Shop Raspberry Pi 4 4GB Full Kit – Plug & Play Setup Affordable power for your projects – Raspberry Pi 4 2GB ! What makes this model Great? The speed and performance of the new Raspberry Pi 4 4GB are a noticeable improvement from earlier models. For the first time, the Raspberry Pi Foundation has created a complete desktop experience. Whether you're editing documents, browsing the web with multiple tabs open, managing spreadsheets, or creating a presentation, you'll find the experience smooth and familiar. It is a more energy-efficient and cost-effective machine. Features Broadcom 2711 Quad-Core Cortex A72 @ 1.5GHz delivers 20% faster performance with improved power and thermal efficiency. Dual micro-HDMI outputs support dual 4K displays with hardware video decode at 4Kp60 (H.265, H.264, MPEG-4). Dual-band WiFi (802.11b/g/n/ac) on 2.4GHz & 5GHz with advanced PCB antenna for robust wireless connectivity. Bluetooth 5.0 offers an extended range of wireless peripherals. Upgraded USB 3.0 Ethernet provides wired speeds up to 10x faster than previous models. 2 USB 3.0 and 2 USB 2.0 ports enable versatile peripheral connections. 40-pin GPIO header is fully backwards-compatible with earlier Pi models. Optional PoE support is available, with PoE header pins designed to work with proper standoffs. Comparison Table Raspberry Pi 4 Model B Raspberry Pi 5 Raspberry Pi 3 Model B+ Price (INR) ?3599 VIEW ?5129 VIEW ?3649 VIEW Processor 1.5GHz Quad-Core ARM Cortex-A72 2.4GHz Quad-Core ARM Cortex-A76 1.4GHz Quad-Core ARM Cortex-A53 RAM 1GB, 2GB, 4GB, 8GB LPDDR4 2GB, 4GB, 8GB, 16GB LPDDR4 1GB LPDDR2 Wi-Fi Dual-band 802.11ac Dual-band 802.11ac Dual-band 802.11ac Bluetooth 5.0 5.0 4.2 USB Ports 2× USB 3.0, 2× USB 2.0 2× USB 3.0, 1× USB 2.0 4× USB 2.0 Ethernet Gigabit Ethernet Gigabit Ethernet Gigabit Ethernet Video Output 2× Micro HDMI (4Kp60) 2× Micro HDMI (4Kp60) 1× HDMI (1080p) GPIO Pins 40 40 40 Storage MicroSD (SDXC up to 2TB) MicroSD (SDXC up to 2TB) MicroSD (SDHC) Power Supply USB-C USB-C Micro USB Click for Complete Raspberry Pi Kits – Learn, Build, and Innovate! Pin Diagram:

CNC Shield for Arduino The CNC shield for Arduino has total four slots, can drive 4 A4988 stepper motors. Each road stepper motors only need two IO ports. In other words, six IO ports can be well managed three stepper motors. The CNC Shield V3.0 allows you to build a engraving machine, 3D printer, mini CNC and other similar devices using your Arduino. It is designed as a shield and can plug on top of an Arduino requiring no external connections and wiring. There are 4 slots on the board for plugging in stepper motor drive module which can drive 1 stepper motor each. Controlling each step stepper motor requires only two IO pins on the Arduino. Just insert this Arduino CNC Shield V3.0 onto an Arduino UNO , and install the GRBL firmware, you can then quickly build a DIY CNC engraving machine. This arduino shield is very convenient to use and is suitable for development boards compatible with Arduino. This CNC shield compatible with Arduino is the latest version of the CN shield model (V 3.0). The CNC Shield is GRBL 0.9 compatible and with the help of jumper wires , it is accessible to stepper drivers. Features: Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place. GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals) 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)

CNC Shield + UNO R3 Board compatible with Arduino + 4xDRV8825 Driver Kit Arduino Uno is an open-source microcontroller used by students and hobbyists entering the world of DIY electronics and automation, The Arduino Uno can be used for any application including being the brains of your next DIY 3D printer and/or CNC router The CNC Shield V3.0 allows you to build an engraving machine, 3D printer, mini CNC and other similar devices using your Arduino. It is designed as a shield and can plug on top of an Arduino requiring no external connections and wiring. Along with that, the CNC shield allows you to control up to four stepper motors by mounting on 4 stepper motor drivers, included with this kit The DRV8825 provides an integrated motor driver solution for printers, scanners, and other automated equipment. The device has two H-bridge and is intended to drive a bipolar stepper motor. Features: UNO R3 Board: The main microcontroller board compatible with Arduino. CNC Shield: An expansion board that allows for easy connection and control of stepper motors. 4x DRV8825 Stepper Motor Drivers: High-performance drivers for controlling stepper motors. Micro-Stepping: Supports micro-stepping settings for precise control of stepper motors. GRBL Compatibility: Compatible with GRBL firmware, which is widely used for CNC control. Voltage Range: Operates on 12-36V DC. Heat Sinks: Included for cooling the stepper motor drivers. USB Cable: For connecting the UNO R3 board to a computer. 40-Pin Row Needles: For additional connections. Applications: CNC Machines: Used for controlling stepper motors in CNC milling, engraving, and cutting machines. 3D Printers: Essential for driving stepper motors in 3D printers, ensuring precise layer deposition and movement. Laser Cutters: Controls stepper motors in laser cutting machines for accurate cutting and engraving. Robotics: Ideal for robotics projects requiring precise motor control, such as robotic arms and automated guided vehicles (AGVs). X-Y Tables: Used in X-Y tables for accurate positioning and movement in various industrial applications. Pick-and-Place Devices: Employed in pick-and-place machines for accurate component placement in electronics manufacturing. Labeling Machines: Used in labeling machines for precise label application. Pinout Diagram for the Arduino Uno Microcontroller Applications of the Kit The kit can be used to create custom 3D printers, scanner, CNC mills and other automated equipment applications

7Semi High-Precision Temperature & Humidity Sensor Probe The 7Semi High-Precision One-Wire Temperature and Humidity Probe is engineered for applications where accuracy, durability, and reliability truly matter. Built with advanced CMOSens sensing technology, it delivers precise digital measurements even in extreme environmental conditions. Its stainless-steel porous housing provides excellent protection against moisture, dust, and chemical contaminants, making it dependable for long-term use in demanding setups. Designed for industrial automation, scientific research, HVAC systems, and environmental monitoring, this probe offers excellent responsiveness and stability across wide temperature and humidity ranges. The one-wire interface reduces wiring complexity, while the compact form factor and 1-meter cable make installation effortless. With its industrial-grade sensing, high-accuracy performance, and rugged enclosure, this probe is ideal for both stationary and mobile applications. Features: Designed with advanced CMOSens technology to deliver highly accurate humidity and temperature readings in challenging environments. Operates efficiently at 3.3V, making it suitable for battery-powered and portable devices. Works across extreme environmental conditions, including temperatures from -40°C to +125°C and pressures up to 150 bar. Encased in a stainless-steel breathable shell that resists corrosion, dust, chemical exposure, and moisture. One-wire digital interface ensures simple integration and minimal wiring requirements. Proven reliability in high-pressure, high-temperature, vacuum, and explosive environments. Built for long service life with strong resistance to oxidation and particulate blockage. Includes a 1-meter cable with a mini round shell connector for flexible installation in tight or specialized spaces. 7Semi High-Precision Temperature & Humidity Sensor Probe Pinout Diagram:

Cytron Maker Object – Digital IR Proximity Sensor The Cytron Maker Object is a compact digital IR proximity sensor designed for beginners, hobbyists, and robot builders who need reliable object detection or obstacle sensing in their projects. Engineered with a 38kHz modulated IR signal, the Cytron sensor remains immune to ambient light, ensuring stable readings in both indoor and outdoor environments. Its active-low NPN output, internal pull-up resistor, and easy plug-and-play interface make it ideal for robotics, automation, and DIY electronics projects where simplicity and accuracy matter. Despite its tiny form factor, the Cytron Maker Object IR sensor offers impressive sensing capability with an adjustable detection range: 15–60 cm for dark surfaces and 40–140 cm for light surfaces. The 90-degree header design allows effortless mounting on PCBs, breadboards, or compact robots such as mini sumo bots. Whether you’re building an obstacle-avoidance robot, an automatic gate safety sensor, a parking occupancy counter, or an entrance detection system, the Cytron Maker Object delivers dependable performance in a small, beginner-friendly package. Features: Cytron’s compact digital IR proximity sensor designed for easy object and obstacle detection. 38kHz modulated IR signal provides strong immunity to ambient light interference. Active-low NPN output with internal pull-up resistor for direct microcontroller compatibility. Adjustable sensing range optimized for different surface colors: 15–60cm (black), 40–140cm (white). Breadboard-friendly design with a 90-degree pin header for effortless mounting on robots or PCBs. Ideal for mini robots, sumo bots, automation setups, safety systems, and DIY electronics.

7Semi SHT41 Temperature & Humidity Sensor Tiny Breakout with I2C Qwiic The 7Semi SHT41 Temperature & Humidity Sensor Tiny Breakout is crafted for engineers, IoT developers, and embedded system designers who need precise environmental monitoring in extremely compact spaces. Powered by the fourth-generation SHT41 sensor, it delivers exceptional accuracy with ±1.8% RH and ±0.2°C precision, making it ideal for sensitive applications like HVAC regulation, smart home devices, and industrial IoT nodes. Its stable readings and fast response time ensure reliable environmental sensing even in dynamic conditions. Designed for low-power performance, this breakout operates on a 3.3V supply and consumes less than 0.15 mA in low-power mode, making it a perfect match for wireless systems and battery-powered deployments. With built-in I2C support, multiple address options, and a compact 1.27 mm pitch connector, integration is quick and hassle-free. Whether you're building connected sensors, indoor air-quality systems, or compact IoT hardware, this module provides dependable data for real-time decision-making and energy-efficient operations. Features: Designed with the advanced SHT41 sensor, offering high-precision measurements with ±1.8% RH humidity accuracy and ±0.2°C temperature accuracy. Operates with ultra-low power consumption, drawing less than 0.15mA in low-power mode to extend battery life in portable systems. Supports I2C communication with multiple configurable addresses for flexible integration in multi-sensor setups. Compact and lightweight form factor with a 1.27 mm pitch 4-pin connector, making it suitable for tight-space and embedded applications. Built for industrial-grade reliability, ensuring consistent performance across typical indoor and light industrial environments. Simple plug-and-play workflow enables quick installation for IoT platforms, smart buildings, automation systems, and environmental monitoring.

7Semi PCA9306 I2C Bidirectional Voltage Level Translator Breakout Board The 7Semi PCA9306 I2C Bidirectional Voltage Level Translator Breakout Board is a compact and efficient PCA9306 voltage level translator designed to safely interface I2C and SMBus devices operating at different logic levels. Supporting voltage translation from 1.2V to 5.0V, this board enables seamless communication between low-voltage sensors and higher-voltage microcontrollers without manual direction control. As a dependable I2C logic level converter, it delivers minimal signal delay and stable bidirectional data flow, making it ideal for robotics, industrial controllers, embedded systems, and DIY electronics projects requiring precise mixed-voltage I2C communication. Allowable Voltage Level Translation The breakout can transfer voltages ranging from 3.3V to 5V. VREF1 (Low Side) VREF2 (High Side) 1.2V 1.8V, 2.5V, 3.3V, 5V 1.8V 2.5V, 3.3V, 5V 2.5V 3.3V, 5V 3.3V 5V Features: Wide Voltage Range Support: Operates between 1.2V and 5.0V, accommodating a wide range of components. Dual Bidirectional Channels: Translates both the SDA and SCL lines for complete I2C compatibility. I2C and SMBus Protocol Support: Fully compatible with regular and fast-mode I2C devices, as well as SMBus peripherals. No Direction Pins Required: Signal direction is automatically detected for easier design. Low propagation delay: A delay of less than 1.5ns maintains data integrity at high speeds. 5V Tolerant I/O Ports: Securely links 5V signals to lower voltage devices. Compact and simple to use: ideal for embedded applications, prototyping, and compact systems.

7Semi ENS160 Air Quality Sensor I2C Probe (ES-12183) The 7Semi ENS160 Air Quality Sensor I2C Probe (ES-12183) is a compact and ready-to-use air quality sensing module built to measure indoor environmental conditions. It uses the advanced ENS160 multi-gas sensor to detect volatile organic compounds (VOCs) and other indoor pollutants, helping you understand the quality of the air around you. The probe provides clean, processed digital outputs that make monitoring easy. This sensor communicates over a standard I2C interface and works at 3.3 V, making it simple to connect to popular controllers like Arduino, ESP32, or Raspberry Pi. With features like long-term stability, low power use, and reliable performance across a range of temperatures and humidity levels, it’s a great choice for smart home systems, air purifiers, HVAC monitoring, and other environmental projects. Features: Advanced ENS160 multi-gas sensor for indoor air quality monitoring Detects VOCs and air quality levels for healthier environments I2C digital interface for simple integration with microcontrollers Factory-calibrated sensor for reliable and consistent readings Low power consumption, suitable for continuous monitoring Compatible with Arduino, ESP32, Raspberry Pi, and IoT systems 7Semi I2C Wire Color Code

SmartElex BX404 Digital PIR Motion Sensor The SmartElex BX404 PIR Motion Sensor is a compact and reliable BX404 PIR Motion Sensor designed to detect human movement using passive infrared technology. It helps users sense motion accurately by detecting changes in body heat, making it useful for security, automation, and energy-saving applications. This passive infrared sensor is ideal for students, makers, educators, engineers, and startups looking to add motion detection to their electronic projects in a simple and effective way. The sensor works smoothly with popular platforms such as Arduino, Raspberry Pi, and ESP32, allowing easy integration into robotics, IoT devices, and automation systems. Its stable digital output makes it suitable for applications like smart lighting, intrusion alarms, occupancy detection, and DIY prototypes. With easy interfacing and dependable performance, this sensor enables quick development of motion-based solutions for real-world electronics projects. Features: Accurate motion detection using passive infrared sensing Designed for reliable human movement detection Digital output for easy interfacing with controllers Compatible with Arduino, Raspberry Pi, and ESP32 Low power operation for continuous monitoring Ideal for security, automation, and smart electronics projects

SmartElex Hall Sensor The SmartElex Hall Sensor is a compact electronic component designed to detect magnetic fields using the Hall effect. It helps sense the presence, strength, or change in magnetic fields without physical contact, making it useful for reliable and wear-free detection. This sensor is suitable for students, makers, engineers, educators, and startups who are working on electronics projects that require accurate magnetic field sensing, position detection, or rotational speed measurement. This hall effect sensor is widely used in robotics, IoT devices, automation systems, and general prototyping applications. It can be easily interfaced with popular development platforms such as Arduino, Raspberry Pi, and ESP32, allowing quick integration into both learning projects and real-world systems. Common use cases include motor speed sensing, position detection, proximity sensing, and safety switches, where consistent performance and simple integration are important. Features: Detects magnetic fields using the Hall effect principle Contactless sensing for reliable and wear-free operation Fast response suitable for speed and position detection Digital/analog output (depending on variant) for easy interfacing Compatible with Arduino, Raspberry Pi, ESP32, and other controllers Ideal for motor control, proximity sensing, and automation projects

7Semi BMA400 3-Axis Digital Accelerometer Breakout Board STEMMA QT / Qwiic The 7Semi BMA400 3-Axis Digital Accelerometer Breakout Board STEMMA QT / Qwiic features the highly precise BMA400 3-axis accelerometer, delivering accurate 3D acceleration measurements with 12-bit digital resolution and 0.001g sensitivity. Supporting selectable measurement ranges of ±2g, ±4g, ±8g, and ±16g, this ultra-low power sensor can detect tilt, orientation, tap/double-tap, and perform step counting with activity recognition—making it perfect for wearable devices and battery-sensitive applications. Its Qwiic/STEMMA QT connector allows effortless plug-and-play integration, while dual power support (3.3V/5V) and flexible I2C/SPI interfaces ensure compatibility with a wide range of microcontrollers. With two configurable interrupt pins and a compact design, this breakout board is ideal for robotics, motion sensing, vibration monitoring, and other STEM projects requiring precise and reliable acceleration data. Features: 3.3 and 5 volt power supply I2C and SPI communication, with 2 interrupt pins. Digital resolution: 12 bits. Measurement range: +- 2g, 4g, 8g, 16g. BMA400 3-Axis Digital Accelerometer Breakout Pinouts:

Radiolink FPV Mobile Phone Holder Stand Folding Mount for RC4GS V3/V2 & RC6GS V3/V2 Controllers The Radiolink FPV Display Monitor Screen Holder is designed to securely hold mobile phones or FPV display screens on your RC controller. Simply insert the mount into the controller’s 1/4” (M6) thread hole, place your phone or monitor on the holder, and adjust the angle using the 360° rotating ball head. This makes it easy to achieve the perfect viewing position while flying, whether indoors or outdoors. This foldable and lightweight holder extends from 5.5cm to 9cm, supporting FPV monitors up to 4.3 inches and mobile phones up to 6.8 inches. Compatible with Radiolink RC4GS V2/V3, RC6GS V2/V3, and other devices with a standard thread hole, it is made of durable plastic and metal to withstand impact. Weighing only 105g, it is easy to install, remove, and carry, making it a reliable accessory for FPV enthusiasts. Features: Holds mobile phones or FPV display monitors securely 360° adjustable ball head for optimal viewing angles Extendable from 5.5cm to 9cm Supports FPV monitors up to 4.3 inches and phones up to 6.8 inches Compatible with Radiolink RC4GS V2/V3, RC6GS V2/V3, and devices with 1/4” (M6) thread hole Lightweight and durable, made of plastic and metal Easy to install, remove, and carry

7Semi INA219 Triple-Channel DC Current Monitoring Sensor Breakout The 7Semi INA219 3-Channel DC Current Sensor Breakout is designed for makers, engineers, and system developers who need high-accuracy, real-time monitoring of voltage, current, and power across multiple DC loads. With three independent measurement channels, this board lets you track power usage holistically, ideal for multi-device systems, battery-powered projects, or performance-critical circuits. Its precise readings up to 26V and 3.2A make it a dependable choice for applications where stable power management matters. Equipped with an I2C interface, programmable addressing, and dual Qwiic I2C ports, this breakout simplifies integration into embedded systems, IoT setups, and advanced monitoring projects. Whether you’re optimizing battery health, managing motor loads, or evaluating system efficiency, this sensor board ensures reliable performance and accurate insights with embedded power-monitoring intelligence and flexible configuration options. Features: Provides three independent DC current-measurement channels, allowing simultaneous monitoring of multiple loads for comprehensive system analysis. Measures up to 3.2A current and 0–26V DC voltage with high accuracy, enabling precise power diagnostics in embedded systems. Uses a reliable I2C communication interface with 16 programmable addresses, supporting multi-sensor setups without conflicts. Offers dual Qwiic I2C ports for quick, solder-free connections and easy integration into existing development environments. Supports detailed monitoring of voltage, current, and calculated power, giving users full visibility into energy usage. Designed for battery management, motor control, IoT devices, and power-supply diagnostics requiring accurate real-time data.