AC/230V - 35mm 230V AC Continuous Buzzer

Female to Female Jumper Wires (20cm) 40pcs These are 20cm 40pcs Female to Female Jumper wires, very Flexible and easily detachable. These jumper cables have 1Pin female to the 1pin female header with both ends. Also, it is compatible with 2.54 mm mil spacing pin headers. This cable is an electrical wire or group of them in a cable with a connector or pins at each end, which is normally for interconnecting the components of a breadboard or other prototype or test circuit, internally or with other equipment or components, without soldering. Individual Dupont Cables are fitted by inserting their end connectors into the slots provided in a breadboard, the header connector of a circuit board, or a piece of test equipment. Mostly Dupont cables are useful with Orange Pi, Banana Pi, Raspberry Pi , Arduino , and other mini PCs and development boards . It is very useful in the PCB project, PC motherboard, as well as Breadboard connections. Additionally, these jumper wires allows you to plug and unplug easily for prototyping and can be used over and over again. Check out the best selection of Jumper Wires . Applications: Raspberry Pi Arduino PCB projects Breadboard connections Get a complete set of M2M, M2F, F2F Jumper Wires Set for DIY projects.

A3967 Stepper Motor Driver This A3967 Stepper Motor Driver For Arduino is the most recent version of EasyDriver v44, which was created in collaboration with Brian Schmalz. When compared to previous versions, it offers more flexibility and control over your stepper motor . It is a simple stepper motor driver that is compatible with most microcontrollers and capable of producing a digital 0 to 5V pulse (0 to 3.3V pulse if you solder SJ2 closed on the EasyDriver). A 7V to 30V power supply is required for the module's motor. The digital interface is powered by an onboard voltage regulator that can be set to 5V or 3.3V. The A3967 is a full-featured microstepping motor driver with an integrated transistor. It is intended for use with bipolar stepper motors in full-, half-, quarter-, and eighth-step modes, with output drive capabilities of 30 V and 750 mA. The A3967 comes with a fixed off-time current regulator that can operate in slow, fast, or mixed current-decay modes. This current-decay control scheme produces less audible motor noise, higher step accuracy, and lower power dissipation. The transistor is essential to the A3967's simple implementation. Simply sending one pulse to the STEP input causes the motor to move one step (full, half, quarter, or eighth depending on two logic inputs). It is not necessary to programme phase-sequence tables, high-frequency control lines, or complex interfaces. The A3967 interface is ideal for applications where a complex P is either unavailable or overburdened. Features: A3967 microstepping driver Adjustable current control from 150mA/phase to 750mA/phase MS1 and MS2 pins are broken out to change microstepping resolution to full, half, quarter and eighth steps (defaults to eighth) Compatible with 4, 6, and 8-wire stepper motors of any voltage Breadboard-compatible pins.

CNC Shield for Arduino The CNC shield for Arduino has total four slots, can drive 4 A4988 stepper motors. Each road stepper motors only need two IO ports. In other words, six IO ports can be well managed three stepper motors. The CNC Shield V3.0 allows you to build a engraving machine, 3D printer, mini CNC and other similar devices using your Arduino. It is designed as a shield and can plug on top of an Arduino requiring no external connections and wiring. There are 4 slots on the board for plugging in stepper motor drive module which can drive 1 stepper motor each. Controlling each step stepper motor requires only two IO pins on the Arduino. Just insert this Arduino CNC Shield V3.0 onto an Arduino UNO , and install the GRBL firmware, you can then quickly build a DIY CNC engraving machine. This arduino shield is very convenient to use and is suitable for development boards compatible with Arduino. This CNC shield compatible with Arduino is the latest version of the CN shield model (V 3.0). The CNC Shield is GRBL 0.9 compatible and with the help of jumper wires , it is accessible to stepper drivers. Features: Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place. GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals) 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)

CNC Shield + UNO R3 Board compatible with Arduino + 4xDRV8825 Driver Kit Arduino Uno is an open-source microcontroller used by students and hobbyists entering the world of DIY electronics and automation, The Arduino Uno can be used for any application including being the brains of your next DIY 3D printer and/or CNC router The CNC Shield V3.0 allows you to build an engraving machine, 3D printer, mini CNC and other similar devices using your Arduino. It is designed as a shield and can plug on top of an Arduino requiring no external connections and wiring. Along with that, the CNC shield allows you to control up to four stepper motors by mounting on 4 stepper motor drivers, included with this kit The DRV8825 provides an integrated motor driver solution for printers, scanners, and other automated equipment. The device has two H-bridge and is intended to drive a bipolar stepper motor. Features: UNO R3 Board: The main microcontroller board compatible with Arduino. CNC Shield: An expansion board that allows for easy connection and control of stepper motors. 4x DRV8825 Stepper Motor Drivers: High-performance drivers for controlling stepper motors. Micro-Stepping: Supports micro-stepping settings for precise control of stepper motors. GRBL Compatibility: Compatible with GRBL firmware, which is widely used for CNC control. Voltage Range: Operates on 12-36V DC. Heat Sinks: Included for cooling the stepper motor drivers. USB Cable: For connecting the UNO R3 board to a computer. 40-Pin Row Needles: For additional connections. Applications: CNC Machines: Used for controlling stepper motors in CNC milling, engraving, and cutting machines. 3D Printers: Essential for driving stepper motors in 3D printers, ensuring precise layer deposition and movement. Laser Cutters: Controls stepper motors in laser cutting machines for accurate cutting and engraving. Robotics: Ideal for robotics projects requiring precise motor control, such as robotic arms and automated guided vehicles (AGVs). X-Y Tables: Used in X-Y tables for accurate positioning and movement in various industrial applications. Pick-and-Place Devices: Employed in pick-and-place machines for accurate component placement in electronics manufacturing. Labeling Machines: Used in labeling machines for precise label application. Pinout Diagram for the Arduino Uno Microcontroller Applications of the Kit The kit can be used to create custom 3D printers, scanner, CNC mills and other automated equipment applications

TL-Smoother module for 3D printer motor drivers V1.0 A smoother module for stepper driver motor is an add-on module for stepper motors of 3D Printers. It is useful for a softer movement in Delta Style 3D Printer as when using DVR8825 or step and drives and A4988/2 driver unit. TL smoothers are popular little printed circuit boards (PCBs) that are often used in FDM 3D printers to not surprisingly, smooth out the look of prints. In other words, they reduce surface artifacts caused by irregular stepper motor motion, often dubbed “zebra stripes,” “salmon skin,” etc. These smoothers are often sold as 4- and 8-diode variants, with the 8-diode ones (pictured above) offering a stronger smoothing effect. They plug into any 3D printer between the stepper drivers and the stepper motors, working their electrical “magic” without any other setup needed. Their low cost, plug-and-play functionality, and seemingly magical effect have made them quite beloved, albeit slightly controversial. The board provides flyback diodes (freewheeling diodes) for the motor outputs so that they are also protected against induction voltages in the unpowered state of the driver. You will get smoother movement. Features: Suitable for all FDM types of 3D printers Lower vibration, lower noise, and smoother result. Smoother movement especially on the delta-style 3Dprinter under DVR8825 stepper drivers and A4988/2 drivers.

SmartElex NS412 Digital PIR Motion Sensor Module The SmartElex NS412 PIR Motion Sensor is a compact NS412 PIR Motion Sensor module designed for accurate human body detection in electronic and automation projects. It helps users detect movement by sensing changes in infrared radiation, making it useful for security, energy saving, and smart control applications. This human body detection module is suitable for students, makers, educators, engineers, and startups who want a simple and reliable way to add motion sensing to their projects. The sensor works smoothly with popular platforms such as Arduino, Raspberry Pi, and ESP32, allowing easy integration into robotics, IoT devices, and automation systems. Its stable digital output makes it ideal for applications like smart lighting, intrusion detection, occupancy sensing, and DIY prototypes. With easy interfacing and dependable performance, this module enables developers to quickly build motion-based solutions for real-world use. Features: Accurate motion detection using infrared sensing technology Designed for reliable human body detection applications Digital output for easy connection with microcontrollers Compatible with Arduino, Raspberry Pi, and ESP32 boards Low power operation suitable for continuous monitoring Ideal for security systems, smart lighting, and automation projects

Cytron Maker UNO X – Arduino Compatible Development Board for Classroom The Cytron Maker UNO X is a beginner-friendly, classroom-ready Arduino-compatible development board designed to simplify STEM education. Equipped with built-in LEDs on every digital pin, a programmable push button, a piezo buzzer, and a powerbank-friendly design, it eliminates messy wiring and allows students to start coding instantly. This board is ideal for Arduino beginners, school STEM labs, coding clubs, training centers, and anyone learning microcontroller basics. With plug-and-play functionality and seamless compatibility with Arduino IDE, it delivers a smooth learning experience for educators and students alike. Created with the needs of teachers in mind, the Cytron Maker UNO X features an onboard half-size breadboard and perfboard for quick prototyping, making it easy to build hands-on electronics projects right out of the box. Powered by the ATmega328P, and complete with essential interfaces like UART, SPI, I2C, PWM pins, and analog inputs, this board is perfect for exploring coding, electronics, and robotics in a structured classroom setup. Whether for STEM workshops, school projects, or Arduino training programs, Maker UNO X provides an engaging, frustration-free learning experience. Features: Fully Arduino UNO-compatible board designed specially for classrooms and STEM beginners. Built-in LED indicators on every digital pin, allowing students to visualize code output instantly without wiring. Includes piezo buzzer, programmable push button, and powerbank-friendly operation for portable projects. Comes with an onboard perfboard prototyping area and a half-size breadboard to simplify hands-on experiments. Powered by the reliable ATmega328P microcontroller with 16MHz clock speed and full support in Arduino IDE. Offers 20 digital I/O pins, 6 PWM pins, 6 analog inputs, and communication interfaces (UART, SPI, I2C). Features 32KB Flash, 2KB SRAM, 1KB EEPROM, making it ideal for beginner programming and small-scale electronics projects. Uses a USB Micro-B interface with CH9340 USB-UART chip (note: not supported on Windows 7). Designed by Cytron to support educators - ensures faster learning with fewer wiring issues and more hands-on coding.

SmartElex TPS61040 12V Boost Converter Module SmartElex TPS61040 12V Boost Converter Module is designed to step up lower DC voltages to a stable 12V output, making it an ideal solution when your circuit requires a higher operating voltage than the available power source. This 12V boost converter is especially useful for students, hobbyists, engineers, educators, and startups working with battery-powered electronics or low-voltage microcontroller projects. It solves the challenge of powering 12V devices from compact power supplies like 3V or 5V inputs, without needing bulky transformer-based solutions. As a 3V to 12V boost converter, it integrates easily with platforms like Arduino, Raspberry Pi, ESP32, and other development boards, making it highly suitable for robotics, IoT nodes, portable gadgets, automation circuits, and prototyping environments. Its compact design and reliable output make it a practical choice for powering sensors, actuators, communication modules, and small peripherals that need a 12V line. This module helps builders maintain efficiency and portability in their designs while ensuring stable performance across a range of real-world applications. Features: Steps up lower DC input to a stable 12V output Based on the TPS61040 high-efficiency boost converter IC Enables 12V operation from 3V, 5V, or other low-voltage sources Ideal for battery-powered and portable electronics Compatible with Arduino, Raspberry Pi, ESP32, and similar boards Suitable for sensors, small modules, IoT devices, and automation projects

7Semi SHT40 Temperature & Humidity Sensor Breakout I2C Qwiic SHT40 Breakout (ES-13514) The 7Semi SHT40 Temperature & Humidity Sensor Breakout (I2C Qwiic) is a compact and reliable sensor module designed to measure both temperature and humidity with high accuracy. It is based on the Sensirion SHT40 sensor, making it suitable for modern electronics projects that need precise environmental data. This breakout board supports I2C communication and comes with a Qwiic connector, allowing quick and solder-free connections with microcontrollers like Arduino, ESP32, and Raspberry Pi. Its small size and low power consumption make it ideal for IoT devices, weather monitoring, indoor air quality projects, and learning applications where simplicity and accuracy matter. Features: High-accuracy temperature and humidity sensing using the SHT40 sensor Supports I²C communication for easy integration with microcontrollers Qwiic connector enables quick, solder-free plug-and-play connections Wide measurement range of 0–100% RH and –40°C to +125°C temperature Low-power and compact design, ideal for IoT and battery-powered projects Compatible with Arduino, Raspberry Pi, ESP32, and other development boards SHT40 Board Dimensions

SmartElex FT232 Type C, USB To UART (TTL) Communication Module The SmartElex FT232 Type C USB to UART (TTL) Communication Module is a high-performance communication module designed to bridge USB systems with TTL-based serial devices smoothly and reliably. Built around the genuine FT232RL USB serial interface board, it ensures stable data transfer and wide driver support across multiple operating systems. The USB-C interface offers durability and modern connectivity, while the onboard jumper allows precise selection between 3.3V and 5V TTL output, making it suitable for Arduino, ESP, Raspberry Pi, and other embedded platforms. With clear LED indicators for transmission, reception, and power, this USB to UART TTL converter module simplifies debugging, firmware flashing, and serial communication tasks in both development and production environments. Applications: Programming and Debugging Microcontrollers Serial connection between embedded systems USB to TTL converter for different devices Data logging and monitoring. Integration of IoT devices Cautions: To avoid damage, ensure that the voltage is set correctly using the onboard jumper. This module is intended for TTL level signals; do not connect directly to RS232 ports. Avoid dampness and static discharge. Features: Original FTDI FT232RL chipset for dependable and steady UART connectivity USB Type-C connector improves compatibility and supports contemporary devices. Supports 3.3V and 5V TTL logic levels via jumper selection. Fast data transfer rates of up to 3 Mbps Real-time LED status indicators for TXD, RXD, and power monitoring Compact design is perfect for embedded system integration. Compatible with various operating systems, including Windows, macOS, Linux, Android, and Windows CE. USB-powered with a maximum output current of 500 mA. Plug-and-play capabilities for quick setup and deployment. Suitable for prototyping, debugging, and data logging applications.

SmartElex PAM8403 5V Two-Channel Stereo Mini Class-D Audio Amplifier The SmartElex PAM8403 5V Two-Channel Stereo Mini Class-D Audio Amplifier is a compact audio amplification module designed to deliver clear and efficient stereo sound from low-power audio sources. It solves the need for adding audio output to small electronic projects without bulky components or complex circuits. This module is suitable for students, makers, engineers, educators, and startups who want an easy way to integrate stereo audio into DIY electronics, learning kits, and embedded system prototypes. This stereo mini Class-D audio amplifier is commonly used in robotics, IoT devices, automation systems, and portable electronics that require lightweight and power-efficient audio output. It can be easily interfaced with platforms such as Arduino, Raspberry Pi, and ESP32 to drive small speakers in projects like voice alerts, sound feedback systems, and interactive devices. The simple design and stable performance make it easy to integrate into both prototype builds and finished products, enabling reliable audio output with minimal setup effort. Features: Two-channel stereo Class-D audio amplifier for clear sound output Operates on a 5V power supply, ideal for embedded projects High efficiency design with low heat generation Compact size suitable for space-constrained applications Drives small speakers for stereo audio output Compatible with Arduino, Raspberry Pi, ESP32, and other audio-enabled projects

SmartElex BMM150 3 Axis Magnetometer Sensor The SmartElex BMM150 3 Axis Magnetometer Sensor is a compact digital sensor designed to measure magnetic fields along three axes. It helps users accurately detect orientation and heading, making it useful in projects where direction sensing and magnetic field measurement are required. This sensor is suitable for students, makers, engineers, educators, and startups working on embedded systems, learning projects, and prototype development that need reliable magnetic sensing in a small and easy-to-use form. This 3 axis magnetometer sensor is commonly used in robotics, IoT devices, navigation systems, and automation projects that require compass functionality or motion awareness. It can be easily integrated with popular development platforms such as Arduino, Raspberry Pi, and ESP32, allowing smooth data communication and quick setup. The stable performance and simple interfacing make it ideal for applications like robot navigation, electronic compasses, orientation tracking, and smart sensor-based systems Note - The default configuration of module is I2C interface, for SPI interface remove I2C smd jumper & short SPI smd jumper on module. Features: Measures magnetic field strength along three axes (X, Y, and Z) Enables accurate heading and orientation detection Digital output for easy interfacing with microcontrollers Low power operation suitable for battery-powered projects Compact sensor design for space-constrained applications Compatible with Arduino, Raspberry Pi, ESP32, and other development boards

SmartElex 3.2-inch TFT LCD Resistive Touch Display 240×320 SmartElex 3.2-inch TFT LCD Resistive Touch Display (240×320) is designed to bring both visual output and touch interaction to embedded projects. This 3.2-inch TFT display offers a spacious interface for displaying menus, sensor data, graphics, and control screens, making it a practical choice for students, hobbyists, engineers, educators, and startups. Its resistive touch panel allows users to interact directly with the screen, removing the need for external buttons and providing an intuitive way to navigate project functions or settings. Compatible with Arduino, Raspberry Pi, ESP32, and various microcontroller platforms, this 240×320 TFT LCD display is well suited for IoT dashboards, robotics control stations, automation systems, handheld devices, and interactive prototypes. The combination of touch input and a bright, detailed display helps simplify project design while making interfaces feel more professional. With straightforward connectivity and reliable performance, it supports learning, experimentation, and product development where touch-enabled control and visual feedback are essential. Features: 3.2-inch 240×320 TFT LCD with resistive touch input Provides both display output and interactive touch control Ideal for creating on-screen menus, dashboards, and UI panels Compatible with Arduino, Raspberry Pi, ESP32, and similar boards SPI / parallel interface options for flexible connectivity Suitable for IoT panels, robotics interfaces, automation, and DIY devices

SmartElex 12V 10A Single Channel Automotive Relay Module The SmartElex 12V Relay Module is a compact and reliable 12V relay module designed to safely control high-power electrical loads using low-voltage signals from microcontrollers. It helps users switch devices like motors, lights, pumps, and automotive accessories without directly handling high current, making projects safer and easier to manage. This Single Channel Relay Module is well suited for students, makers, educators, engineers, and startups working on electronics, robotics, or automation projects where dependable load control is required. Built for real-world applications, this relay module integrates smoothly with popular development platforms such as Arduino, Raspberry Pi, and ESP32, making it ideal for robotics control systems, IoT automation, smart vehicles, and DIY prototyping. Its automotive-grade design ensures stable performance in demanding environments, while the simple input interface allows quick integration into new or existing projects. Whether you are building a prototype, an automation solution, or an educational demo, this module offers dependable switching and easy integration for everyday electronics applications. Note: Refer to datasheet in the ATTACHMENTS section for more info. regd. the product. Features: Supports safe switching of 12V DC loads in high-power applications Uses an automotive-grade relay for reliable and long-lasting operation Compact and durable design suitable for space-constrained setups Easy to interface with Arduino, Raspberry Pi, ESP32, and other controllers Low-power trigger allows efficient control using logic signals or switches Suitable for automotive systems, robotics, DIY electronics, and automation projects

SmartElex MicroB USB Breakout Board The SmartElex MicroB USB Breakout Board is a compact adapter board designed to make it easy to access the pins of a Micro-B USB connector for prototyping, development, and testing. It breaks out the USB port into simple pin headers, allowing users to interface USB power and data lines with custom circuits, breadboards, and microcontroller boards. This USB breakout board is ideal for students, makers, educators, and engineers who need a quick and reliable way to add USB connectivity to their electronics projects without designing a custom PCB. This board is commonly used in robotics, IoT applications, embedded system development, device repair, and hardware prototyping where USB access is required for powering circuits or transferring data. It works smoothly with platforms like Arduino, Raspberry Pi, and ESP32, enabling fast integration with both beginner and advanced projects. With its straightforward layout and sturdy connector design, the SmartElex MicroB USB Breakout Board is a practical and efficient choice for workshops, prototyping labs, and DIY electronic builds that require stable Micro-B USB interfacing Features: Micro-B USB connector broken out to easy-to-use header pins Simplifies USB power and data access for prototyping and testing Supports quick integration with breadboards and custom circuits Compatible with Arduino, Raspberry Pi, ESP32, and microcontrollers Ideal for DIY repairs, IoT projects, and embedded hardware development Compact and beginner-friendly design for rapid project setup