4 Wheel Drive Gray Chassis with Castor Wheel Slot

28BYJ-48 5V DC Stepper Motor This 5V DC 28BYJ-48 Stepper Motor is small, inexpensive and high-quality geared step motor. The 28BYJ-48 Stepper Motor and ULN2003 Stepper Motor Driver is a widely popular combination of the stepper motor and stepper driver, because of the stability and reliability of the system. The motor has a reduction ratio of 64:1, so it offers a decent torque for its size at speeds of about 15 RPM. It is a unipolar stepper motor which has 5-wires. As stated before the pack contains ULN2003 Stepper motor driver which is a Mini Stepper Motor Driver.The main purpose of ULN2003 is to amplify the control signals from the Arduino, so as to drive the 28BYJ-48 Stepper Motor. If you will give the ULN2003 Stepper motor driver a certain pulse signal, it will drive step motor to a certain angle.The control of Stepper motor movement angle is done by controlling the number of stepper motor driver pulses. The speed of the stepper motor rotation is also controllable by controlling the frequency of the pulses. Connect the 28BYJ-48 motor with the ULN2003 motor driver then interface this combination of motor and driver with Arduino , do some coding and your 28BYJ-48 Stepper Motor is ready to listen to your commands Features: Stepper motor with a standard interface, when used directly pluggable. A, B, C, D four-phase LED indicator which indicates the status of the stepper motor work. Compact-size stepper motor perfect for small robotics applications. Applications: Cameras for providing precise control and positioning. Tilting of car side mirrors can be controlled using these motors. CNC Machines Robotic Arms Home Automation

12V 10A PWM DC Motor Speed Controller The DC Motor Speed Controller allows controlling the direction of a DC motor using a Pulse-Width-Modulated (PWM) DC voltage with a Duty Cycle fully adjustable from 10%-100%. The 12 Volt DC Motor Speed Controller can provide a continuous current of 10A to your DC motor or other DC load. The circuit also includes a 10A fuse, with the reverse connection of the power supply and control voltage over-voltage protection function. This speed regulator uses a barrier terminal block as its wiring type. The output voltage is linear under load and features a control frequency of 13kHz. Note: This cannot be used for the brushless motor. The controller is not reverse-polarity protected and will be damaged if it connects the supply voltage with the wrong polarity. Features: Control the speed of a DC motor with this controller. High efficiency, high torque, low heat generating. With reverse polarity protection, high current protection. Control voltage over-voltage protection function The overload and short circuit protecting current is 10A Applications: Automotive: Controlling the speed of cooling fans, windshield wipers, and air conditioning systems. Industrial Automation: Managing the speed of conveyor belts, exhaust fans, and other motor-driven machinery. Home Appliances: Adjusting the speed of fans, pumps, and other household devices. Treadmills: Regulating the speed of the treadmill belt for different workout intensities. Robotics: Providing precise speed control for DC motors in robotic projects. DIY Projects: Ideal for custom electronics projects requiring variable motor speed control

1200W PWM Motor Speed Controller with Potentiometer This is a simple and easy-to-use DC motor speed controller of small size, elegant appearance, and stable performance. It is made with a high-quality circuit board which ensures a longer service life. The DC Motor Speed Controller allows controlling the direction of a DC motor using a Pulse-Width-Modulated (PWM) DC voltage with a Duty Cycle fully adjustable from 10%-100%. The motor speed controller can provide a continuous current of 8A to your DC motor or other DC load. Speed Regulator is an important electronic DIY equipment. Do not touch the heat sink with the wiring. If it touches, it may burn the circuit board. Note that this is not a power module. It must be connected to the motor to speed it up. There is no change in the output of the multimeter without the motor. Features: Maximum Power: 1200W The speed of the DC motor can be controlled by adjusting the pulse width modulation (PWM). The knob realizes 0-100% adjustment, supports step-less speed regulation, and facilitates positioning speed.

A3967 Stepper Motor Driver This A3967 Stepper Motor Driver For Arduino is the most recent version of EasyDriver v44, which was created in collaboration with Brian Schmalz. When compared to previous versions, it offers more flexibility and control over your stepper motor . It is a simple stepper motor driver that is compatible with most microcontrollers and capable of producing a digital 0 to 5V pulse (0 to 3.3V pulse if you solder SJ2 closed on the EasyDriver). A 7V to 30V power supply is required for the module's motor. The digital interface is powered by an onboard voltage regulator that can be set to 5V or 3.3V. The A3967 is a full-featured microstepping motor driver with an integrated transistor. It is intended for use with bipolar stepper motors in full-, half-, quarter-, and eighth-step modes, with output drive capabilities of 30 V and 750 mA. The A3967 comes with a fixed off-time current regulator that can operate in slow, fast, or mixed current-decay modes. This current-decay control scheme produces less audible motor noise, higher step accuracy, and lower power dissipation. The transistor is essential to the A3967's simple implementation. Simply sending one pulse to the STEP input causes the motor to move one step (full, half, quarter, or eighth depending on two logic inputs). It is not necessary to programme phase-sequence tables, high-frequency control lines, or complex interfaces. The A3967 interface is ideal for applications where a complex P is either unavailable or overburdened. Features: A3967 microstepping driver Adjustable current control from 150mA/phase to 750mA/phase MS1 and MS2 pins are broken out to change microstepping resolution to full, half, quarter and eighth steps (defaults to eighth) Compatible with 4, 6, and 8-wire stepper motors of any voltage Breadboard-compatible pins.

A4988 Stepper Motor Driver Module with Heat Sink For 3D Printer (Red) A4988 Stepper Motor Driver is a complete micro-stepping motor driver with a built-in translator for easy operation. The product can be full, half, 1/4, 1/8, and 1/16 step mode to operate bipolar stepper motor output drive capacity of up to 35 V and ± 2 A. A4988 includes a fixed off-time current regulator, the regulator can slow or mixed decay mode. The converter is the key to the easy implementation of the A4988. In inputting one pulse on the STEP input drives the motor one micros tep. No phase sequence tables, high-frequency control lines, or complex interfaces to programming. A4988 interface is very suitable for complex microprocessor is unavailable or is overburdened. The micro-step operation, the chopping control in the A4988 automatically selects the current decay mode (Slow or Mixed). In the mixed decay mode, the device is initially set to fast decay in the part of the fixed off-time, then a slow decay in the rest of the downtime. Mixed-decay current control scheme results in reduced audible motor noise, increased step accuracy, and reduced power consumption. Internal synchronous rectification control circuitry to improve the pulse-width modulation (PWM) power consumption when operating. Internal circuit protection includes thermal shutdown with hysteresis, under-voltage lockout (UVLO) and crossover current protection. Special power-Sort. If you want to control the stepper motor with this motor driver, you will need a few essential components like Arduino , breadboard, jumper wires, batteries, and power supply. Features: Simple step and direction control interface Five different step resolutions: full-step, half-step, quarter-step, eighth-step, and sixteenth-step Automatic current decay mode detection/choice. Mixed with slow current decay mode Over-temperature thermal shutdown, under-voltage lockout, and crossover-current protection Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates check out : Stepper Motor Driver Expansion Board

SmartElex Atmospheric Sensor Breakout – BME280 Temperature, Humidity & Pressure Sensor Module The SmartElex Atmospheric Sensor Breakout is a compact and reliable module designed to measure temperature, humidity, and air pressure with high accuracy. Built around the powerful BME280 sensor, this 3-in-1 sensor module makes it easy to monitor environmental conditions in real time. Perfect for weather stations, IoT systems, and smart home devices, this environmental sensor breakout delivers precise readings while consuming very little power. It supports both I2C and SPI communication interfaces, making it simple to connect with popular boards like Arduino, ESP32, or Raspberry Pi. Whether you’re building an automation project or a DIY weather monitor, this temperature, humidity, and pressure sensor breakout provides reliable performance and easy integration. It’s a great choice for makers, students, and developers who want accurate environmental data in a small and efficient module. Features: 3-in-1 Environmental Sensor: Accurately measures temperature, humidity, and barometric pressure using the BME280 sensor. High Precision Readings: Provides stable and accurate data for weather monitoring and environmental analysis. I2C & SPI Compatible: This I2C SPI environmental sensor module easily interfaces with Arduino, ESP32, Raspberry Pi, and other microcontrollers. Compact Design: Small and lightweight, making it perfect for embedded systems, IoT devices, and portable applications. Low Power Consumption: Efficient sensor design ensures reliable long-term use in battery-powered projects. Easy to Integrate: Ideal for beginners and professionals working on DIY weather stations, home automation, or environmental monitoring systems.

7Semi Vikram-3025 High-Power 25A DC Motor Driver for 6–30V Motors The 7Semi Vikram-3025 is a heavy-duty single-channel DC motor driver built for demanding robotics, automation, and mechatronics projects. Designed to handle 25A continuous load with a 6V–30V operating range, it uses a high-efficiency discrete NMOS H-Bridge that eliminates the need for bulky heat sinks. Whether you're powering high-torque DC motors or creating reliable industrial controls, this driver ensures stable, smooth, and responsive performance. With built-in safety features like overcurrent protection, temperature protection, and undervoltage shutdown, your system stays secure even under heavy loads. This motor driver goes beyond basic control, it includes onboard test buttons, motor output LEDs, and a regulated 5V output for powering microcontrollers, making prototyping extremely convenient. It supports PWM/DIR control signals from a wide range of logic voltages (1.8V to 30V), ensuring compatibility with Arduino, Raspberry Pi, PLCs, and other controllers. It also offers manual control options using a potentiometer and switch, giving both beginners and advanced users flexible control in real-world applications. This makes it a dependable choice for custom robotics, high-power motor control, and automation systems. Features: Provides smooth and reliable bidirectional control for single brushed DC motors. Supports a wide operating voltage range from 6V to 30V for flexible motor compatibility. Handles a continuous motor current of 25A, ideal for high-load or high-torque applications. Includes an onboard 5V regulated output (250mA) to power a microcontroller without an external supply. Onboard test buttons and motor state LEDs allow quick, controller-free testing during prototyping. Offers dual input modes: PWM/DIR for digital control or potentiometer/switch for manual operation. Compatible with 1.8V, 3.3V, 5V, 12V, and 24V logic, making it suitable for Arduino, Raspberry Pi, PLCs, and more. Supports PWM input frequency up to 40kHz with a fixed 16kHz output for quiet motor operation. Built-in protections include active current limiting, overcurrent protection, temperature protection, and undervoltage shutdown.

SmartElex Micro ISM330DHCX 6DoF IMU Sensor The SmartElex Micro ISM330DHCX 6DoF IMU Sensor is a compact motion-sensing module that combines an accelerometer and gyroscope to measure movement, orientation, and rotation. It helps users track motion data accurately in three-dimensional space, making it useful for students, hobbyists, engineers, and educators working on robotics, automation, and motion-based electronics. This IMU breakout board simplifies motion tracking in projects where stability, responsiveness, and precision are important, without requiring complex circuit design or calibration setups. This 6DoF IMU sensor is commonly used in self-balancing robots, gesture-controlled systems, IoT wearables, drones, and embedded automation projects that rely on movement or orientation feedback. It integrates smoothly with popular development platforms like Arduino, Raspberry Pi, and ESP32, making setup and data processing beginner-friendly and efficient. With dependable performance and straightforward compatibility, the SmartElex Micro ISM330DHCX is a practical choice for prototyping, academic learning, and product development where reliable motion tracking and sensor fusion are essential. Features: 6DoF IMU with built-in accelerometer and gyroscope for motion tracking Measures linear acceleration and rotational movement in real time Compact breakout board designed for easy integration in projects Compatible with Arduino, Raspberry Pi, ESP32, and similar platforms Ideal for robotics, drones, wearables, and gesture-based control systems Reliable module for prototyping, STEM learning, and embedded development

SmartElex RLS05 Line Follower Sensor The SmartElex RLS05 Line Follower Sensor is a compact and easy-to-use module designed to help robots detect and follow lines on a surface with accuracy. It is ideal for students, makers, educators, and early-stage engineers who are learning robotics or building simple autonomous systems. The sensor simplifies line detection by clearly identifying path contrasts, making it easier to develop reliable line-following behavior without complex circuit design. This sensor is widely used in line follower robots, educational robotics kits, and automation prototypes where precise path tracking is required. It integrates smoothly with popular platforms such as Arduino, Raspberry Pi, and ESP32, allowing quick setup and experimentation. With dependable performance and straightforward interfacing, the SmartElex RLS05 enables users to focus on coding logic and robot movement, making it well suited for classrooms, labs, competitions, and DIY robotics projects in India. Pin Diagram: How to Calibrate SmartElex RLS05 Line Follower Sensor Step 1: Enter Calibration Mode Press the calibration button once or pull the CAL pin low for a few milliseconds. When three LEDs (D0, D2, and D4) turn ON, the module has entered calibration mode. Step 2: White Surface Reading Place the RLS05 module on a white surface and press the calibration button again. When two LEDs (D3 and D4) turn ON, the white surface values are read and saved in EEPROM. Step 3: Black Surface Reading Place the module on a black surface and press the calibration button once more. When three LEDs (D2, D3, and D4) turn ON, the black surface values are read and stored. Step 4: Select Line Following Mode To enable white line following, press the calibration button three times within one second. LEDs (D2, D3, and D4) will blink to confirm selection. To enable black line following, press the calibration button twice. LEDs (D0, D1, and D2) will blink to confirm the mode selection. Features: Five-channel line detection for accurate and stable line following Supports both black line and white line tracking modes One-time calibration with onboard EEPROM memory Easy calibration using onboard push button or CAL pin Compatible with Arduino, Raspberry Pi, and ESP32 platforms Ideal for robotics projects, educational kits, and automation prototypes

Pludo Robotic Walking Dog - STEM Toy on Motion & Robotics for Ages 8–11 | Grade 3 to 5 This Robotic Walking Dog STEM Toy gives children aged 8–11 an exciting opportunity to explore robotics and engineering through hands-on play. Kids can assemble their own electric robot dog, learning how mechanical parts, circuits, and movement work together in a fun and interactive way. It’s a practical introduction to STEM concepts that makes learning feel like play. The kit encourages creativity, problem-solving, and critical thinking while helping children develop fine motor skills and hand-eye coordination. As they assemble and test their robot dog, children gain confidence and a deeper understanding of how science and technology work in the real world. As children build and test the robot dog, they develop creativity, problem-solving skills, critical thinking, fine motor skills, and hand–eye coordination. The kit works by converting electrical energy from a battery into mechanical motion using a motor. When powered on, the motor drives a set of internal gears that transfer and control movement. These interconnected gears move the legs in a coordinated way, creating lifelike walking motion and clearly demonstrating how motors, gears, and linkages are used in robotics. Perfect for curious young minds, this set also doubles as a smart toy, a versatile toy kit, and a DIY kit, offering hours of engaging and educational entertainment. It’s one of the most exciting DIY robotic kits for kids who love exploring, building, and experimenting, making it an ideal gift for home, school projects, or STEM learning activities. What Your Child Will Learn Build a motor-powered dog that walks and moves, learning how electricity converts into motion. Understand the basics of robotics and simple circuits through fun, guided experimentation. Strengthen fine motor skills, focus, and patience while assembling and wiring each part. Learn how motion, balance, and mechanics work together in real-world machines. Boost creative thinking and problem-solving by customizing and troubleshooting the build. Encourage confidence and curiosity — ideal for home learning, classroom activities, or STEM clubs. Educational Outcomes Electricity & Circuits: Discover how power flows through simple connections to make movement possible. Mechanics: Explore how gears, motors, and linkages work together to create motion. Engineering Thinking: Apply logical reasoning and sequencing while assembling the toy. Creativity & Confidence: Learn by doing - experiment, adapt, and see science come alive through play Features: DIY robotic dog that teaches the fundamentals of movement and electricity. Designed for kids aged 8–11 (Grades 3–5) — perfect for age-appropriate STEM learning. Encourages creativity, customization, and critical thinking through hands-on building. Lets kids explore mechanics and electronics in a safe, interactive way. Made from eco-friendly, high-quality materials for durable, safe playtime. Can be used as a smart toy, DIY project, or learning kit for both home and school environments. Sparks curiosity and love for science, technology, and problem-solving in every build.

Anycubic Photon P1 3D Printer The Anycubic Photon P1 is an advanced resin 3D printer engineered to deliver near-industrial precision with user-friendly operation. Featuring a high-resolution optical system with over 92% light uniformity, it ensures sharp details, smooth surfaces, and consistent curing across every layer. Its robust mechanical design, including a precision-ground steel build plate and dual-rail Z-axis system, provides exceptional stability and accuracy, making it ideal for professional-grade applications such as prototyping, dental modeling, and intricate design work. Designed for versatility and performance, the Photon P1 supports a wide range of resins, including high-viscosity industrial materials up to 8000 cps. It also introduces advanced technologies such as Wave Release for reduced peel force and a temperature-controlled resin vat for consistent printing even in challenging conditions. With optional dual-material and dual-color printing capability, it enables users to create complex models in a single print, significantly improving workflow efficiency and creative possibilities. Wave Release Technology Wave Release Technology is an advanced innovation designed to significantly improve the reliability and quality of resin 3D printing. It works by optimizing the layer separation process during printing, reducing the peel force required to detach each cured layer from the film. This reduction in force helps prevent common issues such as layer shifting, model deformation, or print failures, especially in complex or delicate designs. Precision-Fitted Industrial-Grade Ball Screw The precision-fitted industrial-grade ball screw enhances the printer’s Z-axis movement by delivering smooth, accurate, and highly stable vertical motion during the printing process. This high-quality component minimizes mechanical backlash and vibrations, ensuring consistent layer alignment and superior print accuracy even for intricate and detailed models. Its robust construction supports long-term durability and reliable performance, making it suitable for continuous industrial use. By maintaining precise positioning throughout each layer, it significantly improves surface finish and overall print quality, especially in high-resolution resin printing applications. Precision-Ground Steel Build Plate The precision-ground steel build plate is engineered to provide a perfectly flat and stable printing surface, ensuring excellent first-layer adhesion and consistent print quality. Its finely machined surface enhances grip for resin prints, reducing the chances of model detachment during the printing process. This high level of flatness and rigidity improves overall accuracy, especially for detailed and high-resolution prints. Built for durability, the steel construction withstands repeated use and maintains its precision over time, making it ideal for professional and industrial applications. Engineered for Ultra-Viscous 8000cps Resin Engineered to handle ultra-viscous resins up to 8000 cps, this feature allows the printer to work efficiently with thicker, high-performance materials that are typically challenging for standard resin printers. It ensures smooth and consistent resin flow, preventing issues like uneven curing or print defects. This capability expands material compatibility, enabling the use of specialized industrial resins for stronger, more durable, and functional prints. As a result, users can achieve higher-quality outputs with improved mechanical properties, making it ideal for advanced engineering, prototyping, and professional applications. Features: High-resolution resin printing with ultra-fine detail Dual-color and dual-material support (optional) LightTurbo 4.0 optical system for uniform curing Wave Release technology for improved reliability Supports high-viscosity industrial resins (up to 8000 cps) Temperature-controlled resin vat for stable performance Intelligent assistant for automated operation Strong and stable mechanical structure Ideal for dental, prototyping, and miniature printing.

INVENTO 4 Wheel Metal Robot Car Chassis 260x160mm The INVENTO Robot Car Metal Chassis is a durable 4-wheel metal platform designed for building smart car and robotics projects. With a sturdy aluminum alloy frame measuring 260x160x45mm, it provides a strong base for DC geared motors, microcontrollers, and sensors. Ideal for DIY robotics, STEM learning, and automation projects, this robot car chassis offers stability, easy motor mounting, and flexible space for battery packs and control boards. Its solid construction ensures long-lasting performance for educational and hobby applications. Perfect for students, makers, and robotics enthusiasts, this smart car base platform simplifies the development of line follower robots, obstacle avoidance robots, and other mobile robotics projects. Features: Supports wheels up to 125mm (5 inches) in diameter Chassis size: 260 x 160 x 45 mm (L x W x H) with 0.65mm sheet thickness Made from durable powder-coated steel for long-lasting performance Compatible with DC side shaft motors and DC geared motor mounting Designed for four-wheel robot car configuration Chassis color may vary based on stock availability Package includes 1 x metal robot car chassis

7Semi MCP4728 Quad DAC Module The 7Semi MCP4728 Quad DAC Module is a compact and reliable DAC module designed to convert digital signals into precise analog voltage outputs. Based on the MCP4728 IC, this digital-to-analog converter breakout board allows users to generate up to four independent analog outputs using simple I²C communication, making it an efficient solution for applications where microcontrollers lack sufficient analog output pins or require higher accuracy. This module offers easy integration with popular microcontrollers, stable performance, and flexible voltage output control, making it ideal for signal generation, sensor simulation, audio control, and calibration tasks. With its user-friendly design and dependable operation, it is well suited for students learning embedded systems, hobbyists building DIY electronics, and professionals developing prototypes or compact analog control systems. Features: Powered by the Microchip MCP4728 Quad DAC IC 12-bit resolution on all four DAC output channels (A–D) Onboard non-volatile EEPROM retains DAC settings after power-off I²C interface with Fast Mode support up to 400 kHz Low-power operation, ideal for battery-powered projects Compact 7Semi breakout with clearly labeled pinouts Supports LDAC and RDY pins for real-time DAC updates and monitoring Applications: Signal generation (sine, square, and triangle waveforms) Audio voltage control for synthesizers and mixers Programmable and adjustable reference voltage sources Lab instruments, testing, and control systems Industrial automation and process control applications Multi-channel analog and neural interface testing

7Semi SHT40 Temperature & Humidity Sensor Breakout Board with 1.27mm Pitch The 7Semi SHT40 Temperature and Humidity Sensor Breakout is a compact, precision-engineered module built for applications where accurate environmental monitoring and ultra-low power consumption are crucial. Powered by Sensirion’s fourth-generation SHT40 sensor, it delivers highly reliable 16-bit temperature and humidity data while operating at just 3.3V. With its exceptionally low energy usage, fast response time, and robust ±1.8% RH and ±0.2°C accuracy, it’s an ideal upgrade for modern IoT, wearable, and battery-powered designs that demand consistent and stable performance. Designed for effortless integration, the board features a 1.27 mm pitch, a 4-pin header, and a versatile I2C interface with multiple address options, making it simple to deploy across embedded systems, development platforms, and prototype setups. Whether you're building smart home automation, industrial monitoring, or IoT environmental sensing projects, this SHT40 breakout ensures dependable, long-term operation even in demanding ambient conditions, helping engineers and makers achieve more accurate and energy-efficient data processing. Features: The SHT40 sensor delivers high-precision readings with ±1.8% RH humidity accuracy and ±0.2°C temperature accuracy for trustworthy environmental data. Designed for low-power applications, operating at under 0.15mA in low-power mode for extended battery life. Compact breakout board with a 1.27 mm pitch 4-pin header, making it ideal for tight-space electronic designs and fast prototyping. Provides a reliable I2C communication interface with multiple preconfigured addresses for easy use in multi-sensor networks. Efficient 3.3V operation ensures stable performance across microcontroller and IoT platforms. Fast response time of 8 seconds for real-time temperature and humidity tracking. Suitable for smart homes, industrial automation, IoT environmental nodes, air quality systems, and intelligent building applications.

SmartElex LHI778 PIR Motion Sensor Module The SmartElex LHI778 PIR Motion Sensor Module is a passive infrared motion detection solution designed to sense human movement by detecting changes in infrared radiation. It helps solve the problem of automatic motion detection without continuous monitoring, making systems more energy efficient and responsive. This module is suitable for students, makers, engineers, educators, and startups working on electronics projects that require reliable motion sensing for control, security, or automation purposes. This PIR motion sensor module is widely used in robotics, IoT devices, security systems, and home or industrial automation projects where movement detection is required. It can be easily interfaced with popular development platforms such as Arduino, Raspberry Pi, and ESP32, allowing quick integration into prototypes and functional systems. The simple interface and consistent performance make it ideal for applications like motion-activated lighting, intrusion detection, smart alarms, and interactive electronic projects. Features: Passive infrared (PIR) sensor for reliable human motion detection Detects movement by sensing changes in infrared radiation Low power operation suitable for battery-powered projects Digital output for easy interfacing with microcontrollers Compatible with Arduino, Raspberry Pi, ESP32, and similar boards Ideal for security systems, automation, and motion-activated applications