100K Preset Potentiometer - (Pack of 5)

1200W PWM Motor Speed Controller with Potentiometer This is a simple and easy-to-use DC motor speed controller of small size, elegant appearance, and stable performance. It is made with a high-quality circuit board which ensures a longer service life. The DC Motor Speed Controller allows controlling the direction of a DC motor using a Pulse-Width-Modulated (PWM) DC voltage with a Duty Cycle fully adjustable from 10%-100%. The motor speed controller can provide a continuous current of 8A to your DC motor or other DC load. Speed Regulator is an important electronic DIY equipment. Do not touch the heat sink with the wiring. If it touches, it may burn the circuit board. Note that this is not a power module. It must be connected to the motor to speed it up. There is no change in the output of the multimeter without the motor. Features: Maximum Power: 1200W The speed of the DC motor can be controlled by adjusting the pulse width modulation (PWM). The knob realizes 0-100% adjustment, supports step-less speed regulation, and facilitates positioning speed.

10E 3296W Trimpot Trimmer Potentiometer (Pack of 5) 10E 3296W Trimpot is a high accuracy variable resistor and PCB mountable with 3 terminal pins. A general-purpose board mountable preset also called by other names like potentiometers, Trimpots, etc but is just a variable resistor. The voltage between the terminal varies as the trimpot is rotated. The Variable resistors are used for variating voltage as per the need in a circuit. The outer two pins are connected to Vcc and 0V, and the center pin outputs a variable voltage between 0v and Vcc as the rotary cermet is rotated. The potentiometer is easy to mount on a PCB and can be adjusted using a screwdriver. This potentiometer has a single turn, which can be used to preset a value. Applications Can be used to adjust the voltage drop in the circuit Measurement and Test of electronic circuits Can be used to control the intensity of led lights in DIY projects

10K Pot Potentiometer - (Pack of 5) The 10K Pot Potentiometer is a three-terminal variable resistor that is used to vary or change the resistance. It is normally used to control any device. The 10K Potentiometer is used for adjusting various parameters like voltage, current, etc in an electronic circuit. The POT Potentiometer is a passive electronic component that has two end terminals with a resistive element and the sliding contact called the wiper acts as the third terminal. It is mostly used in applications where a single turn can provide enough control resolution. Applications of 10K PoTPotentiometer: DIY kits. Major projects. Mini projects. Audio control. Television control. Motion control. Computation. What are Potentiometers? A potentiometer is a three-terminal resistor with a sliding or rotating contact that forms an adjustable voltage divider.

10K 3386P Trimpot Trimmer Potentiometer (Pack of 5) 10K 3386P Trimpot is a high accuracy variable resistor and PCB mountable with 3 terminal pins. A general-purpose board mountable preset also called by other names like potentiometers, Trimpots, etc but is just a variable resistor. The voltage between the terminal varies as the trimpot is rotated. The Variable resistors are used for variating voltage as per the need in a circuit. The outer two pins are connected to Vcc and 0V, and the center pin outputs a variable voltage between 0v and Vcc as the rotary cermet is rotated. The potentiometer is easy to mount on a PCB and can be adjusted using a screwdriver. This potentiometer has a single turn, which can be used to preset a value. Applications Can be used to adjust the voltage drop in the circuit Measurement and Test of electronic circuits Can be used to control the intensity of led lights in DIY projects

SmartElex RLS-06 Analog & Digital 6 IR Line Sensor Array with Potentiometer The SmartElex RLS-06 Analog & Digital 6 IR Line Sensor Array with Potentiometer is a highly reliable solution for building line-following robots and reflective surface detection systems. Featuring six pairs of IR LEDs and phototransistors, this IR sensor array delivers both analog and digital sensor outputs for flexible performance. Each sensor’s sensitivity can be fine-tuned using the onboard potentiometer, ensuring accurate readings under varying surface conditions. Built around the TCRT5000 reflectance sensor, it offers stable detection of dark and light lines or nearby objects. The module’s MOSFET-controlled LED design helps minimize power consumption, while its dual-stage resistors enable operation at both 5V and 3.3V. Compact, efficient, and precise — the SmartElex RLS-06 is ideal for robotics, automation, and DIY electronics applications. Schematic Diagram: Features: Potentiometer for adjusting the sensitivity of individual sensors. The module serves as a suitable carrier for six evenly spaced pairs of IR emitter and receiver. Uses six sensors for the finest resolution. Very useful in developing rapid line following and grid traversing robots. Comes with simple digital outputs that may be connected directly to microcontrollers. The array contains mounting holes of 3mm diameter for convenient installation.

100K ohm 16mm Rotary Pot Variable Potentiometer Potentiometers are very useful in changing the electrical parameters of a system. It is a single turn 100K Potentiometer with a rotating knob. These potentiometers are also commonly called as a rotary potentiometer or just POT in short.  A potentiometer knob can also be used along with this POT for aesthetic purposes. This is a carbon track, single turn, adjustable resistances, of value 100KOhm Knob potentiometer. It is meant for mounting on panel and is supplied complete with a knob. The knob is affixed on the plastic spindle of the potentiometer and turns the spindle which changes the resistance. The variation of resistance is linearly proportion to the degree of rotation. Potentiometer, in electronic parlance, is a manually variable resistance. Because its most common consumer application is for controlling volume/tone of sound in broadcast receivers, it is loosely referred to as "volume" or ''tone''. It is not a meter with scale and needle. Potentiometers look different depending on size, power handled, application, value and type of material used. There is, however, a common feature-there is wiper which sweeps over a length of resistive material. The two ends of the resistive material as also the wiper are available to the user as electrical terminations. The user gets a variable resistance between the wiper and the two ends.

100 Ohm Trimpot Trimmer Potentiometer - (Pack of 5) A Trimpot or trimmer potentiometer is a small potentiometer that is used for adjustment, tuning, and calibration in circuits. This potentiometer is easy to mount on a PCB and can be adjusted using a screwdriver. What are Potentiometers? A potentiometer is a three-terminal resistor with a sliding or rotating contact that forms an adjustable voltage divider.

DFRobot Gravity Analog Rotation Potentiometer Sensor for Arduino - Rotation 300° The Gravity Analog Rotation Potentiometer Sensor for Arduino is a versatile Arduino rotation sensor that provides a practical way to add manual control to your electronic projects. With its 300-degree rotation range, this analog potentiometer module allows users to input varying voltage levels by simply turning the knob, making it perfect for applications like controlling LED brightness, adjusting motor speed, or creating interactive controls for DIY projects. The sensor features the standardized Gravity interface, ensuring easy plug-and-play connectivity with Arduino boards and compatible microcontrollers without requiring additional wiring or complex setup procedures. What makes this 300-degree rotation sensor particularly useful is its compatibility with both 5V Arduino systems and 3.3V platforms like Raspberry Pi, Intel Edison, Joule, and Curie. This versatility allows students and hobbyists to use the same sensor across different development platforms without worrying about voltage compatibility issues. The Gravity interface potentiometer provides analog output that can be subdivided into 1024 distinct levels, offering precise control for various applications. Whether you're building a smart cooling fan, creating an interactive control panel, or teaching basic analog input concepts, this potentiometer sensor offers a reliable and straightforward solution that's accessible to beginners while being versatile enough for more advanced projects. Features: 300-degree rotation range for precise analog control. Compatible with both 5V and 3.3V systems for versatile use. Gravity interface design for simple plug-and-play connection. Analog output can be divided into 1024 steps for fine adjustment. Works perfectly with IO Sensor Expansion Shield for Arduino. No additional library required for basic functionality. Compact design for easy integration into various projects.

100K 3386P Trimpot Trimmer Potentiometer (Pack of 5) 100K 3386P Trimpot is a high accuracy variable resistor and PCB mountable with 3 terminal pins. A general-purpose board mountable preset also called by other names like potentiometers, Trimpots, etc but is just a variable resistor. The voltage between the terminal varies as the trimpot is rotated. The Variable resistors are used for variating voltage as per the need in a circuit. The outer two pins are connected to Vcc and 0V, and the center pin outputs a variable voltage between 0v and Vcc as the rotary cermet is rotated. The potentiometer is easy to mount on a PCB and can be adjusted using a screwdriver. This potentiometer has a single turn, which can be used to preset a value. Applications Can be used to adjust the voltage drop in the circuit Measurement and Test of electronic circuits Can be used to control the intensity of led lights in DIY projects. Also check the 50K 3386P Trimpot Trimmer Potentiometer (Pack of 5) available on Iotcart. It is a high-accuracy variable resistor with a resistance of 50K Ohms and is PCB mountable with 3 terminal pins. Also check 500K 3386P Trimpot(Pack of 5) . The 500K 3386P Trimpot is a small variable resistor that can be used to adjust voltage in a circuit. It is easy to mount on a PCB and can be adjusted with a screwdriver

10K Pot potentiometer with Knob A 10K Pot potentiometer is a type of variable resistor that is commonly used in electronic circuits. It has a resistance value of 10,000 Ohms, which is indicated by the "10K" in its name. A potentiometer with a knob is a type of manual control that allows you to adjust the resistance of the potentiometer by turning the knob. This is useful for adjusting the level of a signal or the resistance in a circuit. The knob is typically marked with a scale or tick marks to indicate the position of the resistance.

10K Thermistor Temperature Sensor Module(4 Pin) The 10K NTC Thermistor temperature sensor module is a low-cost, small-size module. It is very sensitive to ambient temperature. It is generally used to detect the temperature of the surrounding environment. Through potentiometer adjustment, it is possible to change the temperature detection threshold. DO output can be directly connected to the microcontroller to detect high and low, by detecting temperature changes in the environment. The temperature detection range of the module is between 20 and 80 degrees Celsius. This sensor module can be replaced with a line temperature sensor for controlling the water temperature, water tank, etc. Generally, the 4-wire method of thermistor measurement is the most accurate because there is effectively no current flowing in either of the measurement cable wires and therefore no added resistance due to the cable wires. Module instructions: A thermistor module is sensitive to the environment temperature and is commonly used to detect the temperature of the surrounding environment. The potentiometer adjustment can change the temperature detection threshold (i.e., temperature control), such as the need to control the environment temperature is 50 degrees, while the module corresponding environmental temperature to the green light, the DO output high level, below the set temperature, the output high level, green light don’t. The DO output can be attached directly to the single-chip microcomputer, through single-chip microcomputer to detect the high and low levels, thus detecting the temperature of the environment change. The DO output can be directly driven by our relay module, which can form a temperature control switch and control related equipment operating temperature, also can connect the fan used for cooling, etc. The module of the temperature detection range of 20-80 degrees Celsius. This module can also be replaced with a line of a temperature sensor, used for water temperature, control of the water tank, etc.

10K Preset Potentiometer - (Pack of 5) 10K Preset Potentiometer is a compact variable resistor and PCB mountable with 3 terminal pins. The voltage between the terminal varies as the preset is rotated.  It is a type of variable resistor, It can be easily mounted on PCB and adjusted using a screwdriver. Applications of Preset Potentiometer: Preset potentiometers are widely used throughout electronics wherever adjustments must be made during manufacturing or servicing. The Variable resistors are used for variating voltage as per the need in a circuit. What are Potentiometers? A potentiometer is a three-terminal resistor with a sliding or rotating contact that forms an adjustable voltage divider.

22k Potentiometer (10 pcs) The 22K Pot Potentiometer is a three-terminal variable resistor that is used to vary or change the resistance. It is normally used to control any device. The 22K Potentiometer is used for adjusting various parameters like voltage, current, etc in an electronic circuit. The 22 POT Potentiometer is a passive electronic component that has two end terminals with a resistive element and the sliding contact called the wiper acts as the third terminal. It is mostly used in applications where a single turn can provide enough control resolution. Features: Resistance: 22k ohms. Type: Rotary potentiometer. Power Rating: Typically around 0.5W to 2W, depending on the specific model. Shaft Type: Durable plastic shaft, often with a D-shaped design for easy adjustment. Mounting Style: Usually through-hole or panel mount. Termination Style: Solder lug or PCB pin. Applications: Commonly used in volume controls, tuning circuits, and as adjustable voltage dividers. Quantity: Pack of 10 potentiometers. Applications of 22K PoTPotentiometer: DIY kits. Major projects. Mini projects. Audio control. Television control. Motion control. Computation. What are Potentiometers? A potentiometer is a three-terminal resistor with a sliding or rotating contact that forms an adjustable voltage divider. Also check 47K ohm 16mm Rotatory Variable Potentiometer , and it comes in a pack of 5. The potentiometer has a tolerance of 20% and is a single-turn, carbon track, adjustable resistance component. With a total rotational angle of 300° ± 5°, it can be used to adjust various parameters like voltage and current in electronic circuits.

220K ohm 16mm Rotary Pot Variable Potentiometer Potentiometers are very useful in changing the electrical parameters of a system. It is a single turn 220K Potentiometer with a rotating knob. These potentiometers are also commonly called as a rotary potentiometer or just POT in short.  A potentiometer knob can also be used along with this POT for aesthetic purposes. This is a carbon track, single turn, adjustable resistances, of value 220KOhm Knob potentiometer. It is meant for mounting on panel and is supplied complete with a knob. The knob is affixed on the plastic spindle of the potentiometer and turns the spindle which changes the resistance. The variation of resistance is linearly proportion to the degree of rotation. Potentiometer, in electronic parlance, is a manually variable resistance. Because its most common consumer application is for controlling volume/tone of sound in broadcast receivers, it is loosely referred to as "volume" or ''tone''. It is not a meter with scale and needle. Potentiometers look different depending on size, power handled, application, value and type of material used. There is, however, a common feature-there is wiper which sweeps over a length of resistive material. The two ends of the resistive material as also the wiper are available to the user as electrical terminations. The user gets a variable resistance between the wiper and the two ends. Also check pack of 5 16mm rotary potentiometers with a resistance of 1M ohms . These potentiometers have a tolerance of 20% and are used for adjusting various parameters like voltage and current in electronic circuits. The package includes 5 potentiometers, and each has a total rotational angle of 300° ± 5°.

100K Trimpot Trimmer Potentiometer - (Pack of 5) A Trimpot or trimmer potentiometer is a small potentiometer that is used for adjustment, tuning, and calibration in circuits. This potentiometer is easy to mount on a PCB and can be adjusted using a screwdriver. What are Potentiometers? A potentiometer is a three-terminal resistor with a sliding or rotating contact that forms an adjustable voltage divider.