DC 12V KK-P25/20 8KG Lifting Solenoid Electromagnet This DC 12V KK-P25/20 8KG Lifting Solenoid Electromagnet consists of an iron core and a coil to attract magnetic substances, using the magnetic action induced by electric current, only while the current is applied. This compact functional device offers high power with high reliability. The structure and design to release the residual magnetism left after de-energization is also one of its unique features. Working Principle: An electromagnet is simply a coil of wire. It is usually wound around an iron core. However, it could be wound around an air core, in which case it is called a solenoid. When connected to a DC voltage or current source, the electromagnet becomes energized, creating a magnetic field just like a permanent magnet. The magnetic flux density is proportional to the magnitude of the current flowing in the wire of the electromagnet.The polarity of the electromagnet is determined by the direction of the current. The north pole of the electromagnet is determined by using your right hand. Wrap your fingers around the coil in the same direction as the current is flowing (conventional current flows from + to -). The direction your thumb is pointing in the direction of the magnetic field so north would come out of the electromagnet in the direction of your thumb. DC electromagnets are principally used to pick up or hold objects. Precaution: Electromagnets must meet the following conditions to achieve maximum suction: The object to be sucked must have good magnetic permeability. Proper use of power supply, rated voltage. The object to be sucked must be flat and clean. The object to be sucked must be greater than or equal to the surface of the magnet( For example the magnet is 20 x 15 mm, so the surface area is S=r²π=10²π mm² so the object to be sucked must be greater than or equal to 10²π mm² ) The object to be sucked must be greater than 5mm. (If the thickness decreases, the suction decreases) The object to be sucked must be close, the middle can’t be interspersed with objects or gaps Suction means more than 5cm in thickness, and surface roughness, the surface is greater than the cross-sectional area of the electromagnet and maximum suction completely fits together on an iron-based material. Electromagnet in working conditions electromagnetic conversion would produce a certain amount of heat, electricity more frequently the higher temperature, which is a normal phenomenon. Package Includes: 1 x DC 12V KK-P25/20 8KG Lifting Solenoid Electromagnet 1 x M4 Bolt with Washer Specifications: Model 12V KK-P25/20 Holding/ Suction Force (KG) 8 Operating Voltage (VDC) 12 Max. Operating Current (mA) 0.17 Power Consumption (Watt) 2 Operating Temperature Range (°C) -20 to 120 Cable Length (cm) 30 Bolt Size M4 Body Material Mild Steel Dimensions (Dia x Length) 25 x 20 mm Weight 56 gm

High Sensitivity Water Level Sensor compatible with Arduino Are you tired of inaccurate water level measurements in your Arduino projects? Say hello to the Water Level Depth Detection Sensor for Arduino – your ultimate solution for precise and reliable water level detection. With an operating voltage of DC3-5V and an operating current of less than 20mA, this sensor ensures optimal performance without draining your power supply.Its analog detection area of 40x16mm allows for easy and direct conversion of water to analog signals, enabling your Arduino development board to achieve the desired level alarm effect. Whether you're working on automated irrigation systems, hydroponics, or water tanks monitoring, this sensor's high level/drop recognition capability will provide you with accurate readings every time.Unleash the true potential of your Arduino projects with this cost-effective and user-friendly water level sensor. Don't let inaccuracies hold you back – take the plunge and elevate your projects to new heights of precision and efficiency! When it comes to choosing the right water level sensor for your Arduino projects, ease of integration and performance are crucial factors. Our Water Level Depth Detection Sensor for Arduino checks all the boxes and more!With its streamlined design and analog output, setting up and reading data from the sensor is a breeze. You'll be amazed at how effortlessly it communicates with your Arduino board, making the integration process smooth and hassle-free.Crafted with high-quality materials, this sensor guarantees durability and long-lasting performance, ensuring it stands the test of time in any project you undertake. Its reliable performance will give you the confidence to monitor water levels accurately and make data-driven decisions.Embrace the power of precise water level detection and experience the convenience of working with a sensor that complements your Arduino projects seamlessly. This High Sensitivity Water Sensor can easily change the water size to an analog signal, and output analog value can directly be used in the program function, then to achieve the function of water level alarm. This item has low power consumption, and high sensitivity, which are the biggest characteristics of this module. The High Sensitivity Water Sensor can be compatible with Arduino UNO, Arduino mega2560, Arduino ADK etc. Buy Water Level Sensor now which is High Sensitivity and compatible with Arduino and elevate your Arduino projects to new levels of precision and efficiency. Order now and experience the convenience of working with a sensor that complements your projects seamlessly! Also, read our blog on the Water Level Sensor explaining the different types of water sensors, working, and applications. Pin definition : "S" stand for signal input "+" stand for power supply "-" stand for GND Applications of Water Level Sensor: Water level measurement: The water level sensor can be used to measure the water level in tanks, reservoirs, or other containers Sump pit monitoring: It can be used to monitor the water level in sump pits to prevent flooding Rainfall detection: The sensor can detect rainfall and be used in weather monitoring systems Leak detection: It can be used to detect water leaks in pipes, plumbing systems, or appliances Irrigation control: The water level sensor can be used to monitor the water level in irrigation systems and automate the watering process Aquarium water level monitoring: It can be used to monitor the water level in aquariums and ensure proper water conditions for aquatic life Flood warning systems: The sensor can be used in flood warning systems to monitor water levels in rivers, streams, or flood-prone areas Water level control in industrial applications: It can be used to control the water level in industrial processes or equipment Water level detection in wells: The sensor can be used to monitor the water level in wells and ensure an adequate water supply Water level detection in smart home systems: The sensor can be integrated into smart home systems to monitor water levels and send alerts or automate actions Package Includes: 1 x Water Sensor  Specifications: Working voltage 5V Working Current <20ma Interface Analog Width of detection 40mm×16mm Dimensions  65mm×20mm×8mm Weight  5 grams

Solenoid Valve 12v/24v 1/4 inch (Blue) 12V DC Solenoid Water Air Valve Switch (Normally Closed) – 1/4″ controls the flow of fluid (liquid or air) and acts as a valve between high-pressure fluid. There are two ½” (Nominal NPT) outlets. Normally, the valve is closed. When a 12V DC supply is applied to the two terminals, the valve opens and water can push through. As it is a normally closed assembly, it opens the flow of fluids as soon as it is powered ON and stops/blocks the flow when the supply voltage is removed. This is a 2 way Solenoid Valve sensor. So, it has has 2 connections, one of them is liquid inlet and other is outlet. It accepts DC voltage of 24V. It also works on 12V DC. When there is input voltage on the Solenoid Terminals, it operates, and opens up, allowing the liquid to flow from inlet to outlet. The Solenoid has push fit connectors on each side. So, this connector will allow us to directly push the pipe or nozzle into the solenoid without worrying of leaking. read more : Solenoid Valve - How They Work Package Includes: 1 x Solenoid Valve 12v/24v (Blue) Solenoid Specifications: Working Pressure 0-120PSI Orifice 2.5mm Voltage 12v DC, 24v DC Dimensions  5 x 5 x 5 cms  Weight 25 grams

Solenoid Valve 230V 1/2 inch 230V AC Solenoid Water Air Valve Switch (Normally Closed) – 1/2″ controls the flow of fluid (liquid or air) and acts as a valve between high-pressure fluid. This liquid valve would make a great addition to your robotic gardening project. There are two ½” (Nominal NPT) outlets. Normally, the valve is closed. When a 230V AC supply is applied to the two terminals, the valve opens and water can push through. The valve switch/sensor works with the solenoid coil which operates electronically with AC 230 volt supply. As it is a normally closed assembly, it opens the flow of fluids as soon as it is powered ON and stops/blocks the flow when the supply voltage removed. Also check Solenoid Valve 12v 1/2in designed for solar water heaters. The valve is suitable for liquid media, with a temperature range of 1 - 100 °C. It operates on a 12V DC supply, with a rated current of 0.6A and a power consumption of 8W. The valve is normally closed and has a pressure range of 0.02-0.8Mpa.

Turbidity Sensor With Module for Liquid Particle Detection A turbidity liquid particle detection sensor is a device that is used to measure the turbidity, or cloudiness, of a liquid. Turbidity is often used as an indication of the presence of suspended particles in the liquid, such as dirt, algae, or bacteria. The sensor works by shining a light through the liquid and measuring the amount of light that is scattered or absorbed by the particle detection. Turbidity is the measurement of particulate matter in water. It requires the analog port of the MCU to read the analog value for calculation. It needs turbidity calibration liquid to calibrate. It is not the multimeter that directly measures the voltage. The output voltage of each module is different. The module should be protected from light and light. The temperature and voltage will make the output voltage of the module different.  These decisions are made on the basis of a comparison between clean water measurements (taken at the beginning of the wash cycle) and the wash water turbidity measurement taken at the end of each wash cycle. By measuring the turbidity of the wash water, the dishwasher can conserve energy on lightly soiled loads by only washing as long as necessary. This will result in energy savings for the consumer. Parameters of the Turbidity Particle Sensor: Voltage: 3.3-5V (with anti-reverse circuit) Output: default analog (can set high and low output) Measuring range: 0-1000 NTU Key

3/4 INCH BRASS WATER FLOW SENSOR SEN-HZ43WB The SEN-HZ43WB water flow sensor is a device that is used to measure the flow rate of water. It consists of a turbine-type rotor that is placed in the water stream, and as the water flows past the rotor, it causes the rotor to spin. The sensor measures the speed of the rotor and converts it to a flow rate. The sensor has a digital output, which means that it provides a digital signal that can be read by a microcontroller or other host device. Now easily measure water (liquid) flow in your application using this 3/4" Brass water flow sensor. This is a good-quality flow sensor with a brass body and can be used for industrial and commercial applications. These three forth inch water flow sensor is used extensively in various types of vending machines. This water flow sensor is connected in line with the liquid whose flow rate has to be measured. There is a simple rotating wheel with a magnet and when the liquid flows the wheel is rotated and a hall effect sensor measures how many times the wheel is rotated and accordingly gives pulses. By counting the number of pulses you can easily calculate the flow rate as well as the amount of liquid dispensed. Note: When magnetic material is close to the sensor, its characteristics may vary. In order to avoid particle debris, the sensor must be installed after a filter. The flow sensor installation has to avoid strong vibration and shaking of the environment, so as not to affect the sensor's measurement accuracy. APPLICATIONS: Thermostatic water heater Water purifier Water dispenser Smart card equipment Coffee machine PACKAGE INCLUDES: 1 x SEN-HZ43WB Water Flow Sensor  SPECIFICATIONS: Water quality requirement Drinking water health standards, 0~80℃ Voltage/electric current DC 4.5 ～ 18 Volt, ≤15mA Output level Rated voltage DC 5 Volt, high level ≥4.5 Volt, low level ≤0.5 Volt Cumulative flow conversion 1 Liter water=477 pulse, accuracy: 10%

Analog pH Sensor Electrode with Amplifier Circuit The Analog pH Sensor Kit is the ultimate solution for precise pH measurement in soil and water testing applications. With a measurement range of 0 to 14pH, it provides accurate results for a wide range of pH levels.This kit includes a pH probe and pH Sensor board, making it easy to condition the pH probe's output signal (ranging from 0.5V to 3V). Whether you're a beginner or an experienced user, you'll find this kit user-friendly and efficient.This pH Sensor applications are diverse, from agriculture to aquaculture and water quality testing. The sensor ensures stable readings with quick response times, ensuring you get reliable data for your projects.Compatible with popular development platforms like Arduino and Raspberry Pi, this kit offers versatility for various applications. Trust in the Iotcart Analog pH Sensor Kit for accurate and consistent pH measurements. Few guidelines to use the sensor properly: Make sure the sensor is properly calibrated. Make sure the probe is dipped in deionized distilled water after each reading for at least a minute. Make sure the sensor is given at least a few minutes to settle down in its reading after dipping it in a solution. Here is the link to the pH Sensor Blog for a detailed explanation. Applications: Can be used to determine the PH level in the water Can be used for soil measurements in agriculture Can be used in Aquaculture Pinout Of PH Probe Sensor: Pinout Of PH Sensor TO – Temperature output DO – 3.3V Output (from ph limit pot) PO – PH analog output ==> Arduino A0 Gnd – Gnd for PH probe (can come from Arduino GND pin) ==> Arduino GND Gnd – Gnd for the board (can also come from Arduino GND pin) ==> Arduino GND VCC – 5V DC (can come from Arduino 5V pin) ==> Arduino 5V pin POT 1 – Analog reading offset (Nearest to BNC connector) POT 2 – PH limit setting Package Includes: 1 x pH Probe 1 x pH sensor board Specifications: Operating voltage 5±0.2V (AC - DC) Working current 5-10mA The detection concentration range PH0-14 The detection range of temperature 0-60 centigrade Response Time  ≤ 5S Stability time ≤ 120S Power consumption ≤ 0.5W Size 42mm x 32mm x 20mm Weight 25g

Magnetic Float Sensor FS37A (Vertical) A float switch is a type of level sensor, a device used to detect the level of liquid within a tank. It is a simple structure, easy to use level control device; moreover, it is neither a complicated circuit nor does it provide power. This switch has a mechanical switch than the average small-sized switches. A float switch is a device used to sense the level of liquid within a tank, it may actuate a pump, an indicator, an alarm, or other devices. Use them with hydroponics, saltwater tank, freshwater tank, gardening, aquariums for power head control, pet bowls, fish tanks, filtration, heating, pumps, ponds, basement alarms, boats, air condition drain pans, pressure washers, carpet cleaning machine, reef aquarium, fluid control, ice machines, coffee pots, marine, automotive, automobiles, tropical fish tanks, evaporator coils, condensation line, in relays, or whatever your project may be. It can be easily converted from normally open to normally close by inverting the float. Note: because the current that the switch can carry is much little(0.5A), you must use a relay or contactor when it is connected by a load, relay and contactor are not included here. Check out our entire range of pH, Turbidity & Flow Sensors Key

Float Sensor Contact Type CSSP (Color May Vary) A float sensor contact type CSSP is a level sensor used to detect the level of a liquid in a tank or container. It consists of a float that is attached to a switch, and as the float rises or falls with the level of the liquid, it activates or deactivates the switch. The CSSP sensor is characterized by the fact that it has a contact-type switch, which means that the switch is activated when the float comes into physical contact with a stationary part of the sensor. The sensor is typically used in applications where the liquid level needs to be monitored or controlled, such as in sump pumps, water tanks, and overflow protection systems. It is often preferred over other types of level sensors because it is simple, reliable, and inexpensive. The CSSP float sensor may be used with liquids that are compatible with the materials used in the sensor, and it may have a maximum operating temperature and pressure rating. Package Includes: 1 x Float Sensor Contact Type CSSP (Any Color) Specifications: Dimensions 10x10x5mm Weight  5g

Water Flow Sensor - YF-B6 Flowmeter G3/4 1-30L/min 5-15V Brass Water Flow Sensor (Sea) YF-B6 is the perfect solution for industrial monitoring and water management systems. It is made with brass and plastic materials, measuring 60X OD26mm and featuring a G3/4 thread connection. The sensor includes a Hall effect sensor and digital output, ensuring accurate monitoring of flow rates. Its durable design makes it suitable for a wide range of conditions, perfect for industrial and commercial applications. Water Flow Sensor (Sea) YF-B6 is easy to install and maintain with its compact design. Perfect for engineers, technicians, and hobbyists. Water Flow Sensor (Sea) YF-B6 ensures the highest quality and durability. wire connection : Terminal 1  ( Red) : Vdd  ” + ” Terminal 2 (Black) Vout   ” – ” Terminal 3 ( Yellow )  Gnd : output (13) Connector :  Housing SM2.54-3P Package Includes:  1 x Water Flow Sensor - YF-B6 Flowmeter G3/4 1-30L/min 5-15V Brass Specifications: Material Brass Plastic Flow Sensor Sensor Hall effect sensor, Digital Output Size 60X OD26mm Thread Connection G3/4 Mounting Position Horizontal & Vertical Color Brass golden Flow Rate 1~30 L/min Flow Pulse F= 6.6 *Q ± 5%, Q=L/min Working Voltage DC4.5V ~ 24V Working Current 15mA Suffering Pressure Max 1.5Mpa Working Temperature -40 °C ~+80 °C Min Insulation Resistance 100M Ohm

1/2 Inch Brass Water Flow Sensor SEN-HZ21WI The SEN-HZ21WI water flow sensor is a device that is used to measure the flow rate of water. It consists of a turbine-type rotor that is placed in the water stream, and as the water flows past the rotor, it causes the rotor to spin. The sensor measures the speed of the rotor and converts it to a flow rate. The sensor has a digital output, which means that it provides a digital signal that can be read by a microcontroller or other host device. The sensor is commonly used in applications such as irrigation systems, water treatment plants, and industrial process control. It can easily measure water (liquid) flow in your application using this 1/2" Brass water flow sensor. This is a good quality flow sensor with a brass body and can be used for industrial and commercial applications. This half-inch water flow sensor is used extensively in various types of vending machines. Working of a Flow Sensor: The water flow sensor consists of a copper body, a water rotor, and a hall-effect sensor. When water flows through the rotor, the rotor rolls, its speed changes with different rates of flow. And the hall-effect sensor outputs the corresponding pulse signal. This water flow sensor is connected in line with the liquid whose flow rate has to be measured. There is a simple rotating wheel with a magnet and when the liquid flows the wheel is rotated and a hall effect sensor measures how many times the wheel is rotated and accordingly gives pulses. By counting the number of pulses you can easily calculate the flow rate as well as the amount of liquid dispensed. Note: When magnetic material is close to the sensor, its characteristics may vary. In order to avoid particle debris, the sensor must be installed after a filter. The flow sensor installation has to avoid strong vibration and shaking of the environment, so as not to affect the sensor's measurement accuracy. Applications: Widely used in water industrial fields Thermostatic water heaters Water purifiers Water dispensers Smart card equipment Coffee machines Electric hot water heater Gas water heater Instrument meter  Package Includes: 1 x SEN-HZ21WI Water Flow Sensor Specifications: Model  SEN-HZ21WI Water quality requirement Drinking water health standards, 0~80℃ Output level Rated voltage DC 5 Volt, high level ≥4.5 Volt, low level ≤ 0.5 Volt Flow characteristic F=10 Q-4, F: HZ, Q: L/min，±10% Cumulative flow conversion 1 Liter water = 553 pulses , accuracy: 10%

3/4 Inch Water Flow Sensor SEN-HZ43WA The SEN-HZ43WA water flow sensor is a device that is used to measure the flow rate of water. It consists of a turbine-type rotor that is placed in the water stream, and as the water flows past the rotor, it causes the rotor to spin. The flow sensor measures the speed of the rotor and converts it to a flow rate. The sensor has a digital output, which means that it provides a digital signal that can be read by a microcontroller or other host device. The sensor is commonly used in applications such as irrigation systems, water treatment plants, and industrial process control. It is often preferred over other types of flow sensors because it is easy to install and has a low cost. Package Includes: 1 x Water Flow Sensor SEN-HZ43WA Water Flow Sensor Specifications Model  SEN-HZ43WA Current  15mA @ 5V Flow Rate 2-45L/ min Humidity Range 35%-80% RH Operating Voltage 3V ~ 12V Temperature Range -25 to 80°C Water Pressure 1.75Mpa Dimensions  60mm x 37mm x 37mm Weight  43 grams

1/4 Inch Water Flow Sensor YF - S402 The YF-S402 water flow sensor is a device that is used to measure the flow rate of water. It consists of a turbine-type rotor that is placed in the water stream, and as the water flows past the rotor, it causes the rotor to spin. The sensor measures the speed of the rotor and converts it to a flow rate. The sensor has a digital output, which means that it provides a digital signal that can be read by a microcontroller or other host device. The frequency of the pulses is proportional to the flow rate of the liquid passing through the sensor. That digital signal, whose frequency is in the range between 0Hz and 100Hz, can be read directly through one of the digital input/output pins of a microcontroller. ID 8.5mm / OD 11mm. The water flow sensor measures the rate of a liquid flowing through it. The YF-S402 water flow sensor consists of a plastic valve body, flow rotor, and hall effect sensor. It is usually used at the inlet end to detect the amount of flow. When liquid flows through the sensor, a magnetic rotor will rotate and the rate of rotation will vary with the rate of flow. The hall effect sensor will then output a pulse width signal. Connect it to a microcontroller and you can monitor multiple devices such as your coffee maker, sprinkler, or anything else, and control the water flow rate to suit your needs.

2 Inch Water Flow Sensor YF - DN50 The YF-DN50 water flow sensor is a device that is used to measure the flow rate of water. It consists of a turbine-type rotor that is placed in the water stream, and as the water flows past the rotor, it causes the rotor to spin. The sensor measures the speed of the rotor and converts it to a flow rate. The sensor has a digital output, which means that it provides a digital signal that can be read by a microcontroller or other host device. The sensor is commonly used in applications such as irrigation systems, water treatment plants, and industrial process control. It is often preferred over other types of flow sensors because it is easy to install and has a low cost. The YF-DN50 sensor is designed to be installed in a pipe with a diameter of 50mm or 1.97 inches. The YF-DN50 water flow sensor is a large 2 inch diameter Water Flow meter Sensor that can be used to measure flow rate from 10 - 200 Liter/min This water flow sensor consists of a plastic valve body, a rotor assembly and a Half effect current sensor. As the water flows through this sensor the rotor rotates and the speed of it changes with changes in the rate of flow of water. The hall-effect sensor outputs the corresponding pulse signal. The output of the flow sensor is proportional to the water flow. The more the water flowing more are the pulses.

Float Switch Long Shaft Float Level Switch SEN-PPI150 is the ideal solution for accurately measuring liquid levels. Crafted with advanced Plastic PP material, this switch guarantees durability and longevity. The customizable specifications allow you to tailor the wire harness, float dimensions, warning points, and switching power to meet your specific needs. This cutting-edge technology includes a switching signal for precise liquid level detection, making it suitable for water dispensers, humidifiers, water air conditioning, air conditioning fans, and more. The DC2000V voltage and ≤0.5A electric current provide endless possibilities for water-related activities, making it perfect for users of all skill levels and ages. Designed with reliability in mind, the SEN-PPI150 is crafted with high-quality Plastic PP material, ensuring it thrives in ideal conditions. With various sizes and color options, this float level switch caters to diverse preferences. Float Level Switch is not just a product; it's a solution. It's easy to use and maintain, thanks to its user-friendly design and unique features that address common customer pain points. Whether for households, commercial spaces, or industrial settings, this switch is the go-to choice for accurate liquid level measurement Applications: Water Dispenser, Humidifier, Water Air Conditioning, Air Conditioning Fan, etc. Package Includes: 1 x Float Switch Long Shaft Specifications: Material Plastic PP Switching Signal Yes Temperature Range 0-60 Deg C Voltage/Electric Current DC2000V, ≤0.5A