Turbidity Sensor With Module for Liquid Particle Detection A turbidity liquid particle detection sensor is a device that is used to measure the turbidity, or cloudiness, of a liquid. Turbidity is often used as an indication of the presence of suspended particles in the liquid, such as dirt, algae, or bacteria. The sensor works by shining a light through the liquid and measuring the amount of light that is scattered or absorbed by the particle detection. Turbidity is the measurement of particulate matter in water. It requires the analog port of the MCU to read the analog value for calculation. It needs turbidity calibration liquid to calibrate. It is not the multimeter that directly measures the voltage. The output voltage of each module is different. The module should be protected from light and light. The temperature and voltage will make the output voltage of the module different.  These decisions are made on the basis of a comparison between clean water measurements (taken at the beginning of the wash cycle) and the wash water turbidity measurement taken at the end of each wash cycle. By measuring the turbidity of the wash water, the dishwasher can conserve energy on lightly soiled loads by only washing as long as necessary. This will result in energy savings for the consumer. Parameters of the Turbidity Particle Sensor: Voltage: 3.3-5V (with anti-reverse circuit) Output: default analog (can set high and low output) Measuring range: 0-1000 NTU Key

3/4 Inch Water Flow Sensor SEN-HZ43WA The SEN-HZ43WA water flow sensor is a device that is used to measure the flow rate of water. It consists of a turbine-type rotor that is placed in the water stream, and as the water flows past the rotor, it causes the rotor to spin. The flow sensor measures the speed of the rotor and converts it to a flow rate. The sensor has a digital output, which means that it provides a digital signal that can be read by a microcontroller or other host device. The sensor is commonly used in applications such as irrigation systems, water treatment plants, and industrial process control. It is often preferred over other types of flow sensors because it is easy to install and has a low cost. Package Includes: 1 x Water Flow Sensor SEN-HZ43WA Water Flow Sensor Specifications Model  SEN-HZ43WA Current  15mA @ 5V Flow Rate 2-45L/ min Humidity Range 35%-80% RH Operating Voltage 3V ~ 12V Temperature Range -25 to 80°C Water Pressure 1.75Mpa Dimensions  60mm x 37mm x 37mm Weight  43 grams

Float Sensor Contact Type CSSP (Color May Vary) A float sensor contact type CSSP is a level sensor used to detect the level of a liquid in a tank or container. It consists of a float that is attached to a switch, and as the float rises or falls with the level of the liquid, it activates or deactivates the switch. The CSSP sensor is characterized by the fact that it has a contact-type switch, which means that the switch is activated when the float comes into physical contact with a stationary part of the sensor. The sensor is typically used in applications where the liquid level needs to be monitored or controlled, such as in sump pumps, water tanks, and overflow protection systems. It is often preferred over other types of level sensors because it is simple, reliable, and inexpensive. The CSSP float sensor may be used with liquids that are compatible with the materials used in the sensor, and it may have a maximum operating temperature and pressure rating. Package Includes: 1 x Float Sensor Contact Type CSSP (Any Color) Specifications: Dimensions 10x10x5mm Weight  5g

3/4 INCH BRASS WATER FLOW SENSOR SEN-HZ43WB The SEN-HZ43WB water flow sensor is a device that is used to measure the flow rate of water. It consists of a turbine-type rotor that is placed in the water stream, and as the water flows past the rotor, it causes the rotor to spin. The sensor measures the speed of the rotor and converts it to a flow rate. The sensor has a digital output, which means that it provides a digital signal that can be read by a microcontroller or other host device. Now easily measure water (liquid) flow in your application using this 3/4" Brass water flow sensor. This is a good-quality flow sensor with a brass body and can be used for industrial and commercial applications. These three forth inch water flow sensor is used extensively in various types of vending machines. This water flow sensor is connected in line with the liquid whose flow rate has to be measured. There is a simple rotating wheel with a magnet and when the liquid flows the wheel is rotated and a hall effect sensor measures how many times the wheel is rotated and accordingly gives pulses. By counting the number of pulses you can easily calculate the flow rate as well as the amount of liquid dispensed. Note: When magnetic material is close to the sensor, its characteristics may vary. In order to avoid particle debris, the sensor must be installed after a filter. The flow sensor installation has to avoid strong vibration and shaking of the environment, so as not to affect the sensor's measurement accuracy. APPLICATIONS: Thermostatic water heater Water purifier Water dispenser Smart card equipment Coffee machine PACKAGE INCLUDES: 1 x SEN-HZ43WB Water Flow Sensor  SPECIFICATIONS: Water quality requirement Drinking water health standards, 0~80℃ Voltage/electric current DC 4.5 ～ 18 Volt, ≤15mA Output level Rated voltage DC 5 Volt, high level ≥4.5 Volt, low level ≤0.5 Volt Cumulative flow conversion 1 Liter water=477 pulse, accuracy: 10%

Magnetic Float Sensor FS37A (Vertical) A float switch is a type of level sensor, a device used to detect the level of liquid within a tank. It is a simple structure, easy to use level control device; moreover, it is neither a complicated circuit nor does it provide power. This switch has a mechanical switch than the average small-sized switches. A float switch is a device used to sense the level of liquid within a tank, it may actuate a pump, an indicator, an alarm, or other devices. Use them with hydroponics, saltwater tank, freshwater tank, gardening, aquariums for power head control, pet bowls, fish tanks, filtration, heating, pumps, ponds, basement alarms, boats, air condition drain pans, pressure washers, carpet cleaning machine, reef aquarium, fluid control, ice machines, coffee pots, marine, automotive, automobiles, tropical fish tanks, evaporator coils, condensation line, in relays, or whatever your project may be. It can be easily converted from normally open to normally close by inverting the float. Note: because the current that the switch can carry is much little(0.5A), you must use a relay or contactor when it is connected by a load, relay and contactor are not included here. Check out our entire range of pH, Turbidity & Flow Sensors Key

1/8 Inch Water Flow Sensor YF-S401  The YF-S401 Water flow sensor is a small device comprising a plastic valve body, a water rotor, and a hall effect sensor. As water flows through the Water flow sensor, the internal rotator changes its speed in accordance with the rate of flow, and the hall effect sensor outputs a series of digital pulses. This allows the flow rate to be accurately measured using a microcontroller.This Water flow sensor is ideal for use with laser cutters or CNC machines to monitor the flow of water through the laser tube or spindle for cooling. This Water Flow Sensor has a flow rate of 0.3-6 litres per minute and outputs a pulse for every revolution of the pinwheel sensor. These pulses are approximately 2.25 millilitres each and can be easily counted to calculate the water flow.One of the key advantages of the YF-S401 Water flow sensor is that the hall effect sensor is sealed from the water pipe, ensuring it stays safe and dry. This makes it a reliable and accurate option for measuring water flow in various applications. Connections: Red: Power In Black: Ground Yellow: Signal Output Applications: Water heaters Water vending machine Flow measurement device Automatic water dispenser Agriculture Food processing Coffee/Tea makers Water Management Package Includes: 1 x YF-S401 1/8 inch Water Flow Sensor Specifications: Model  YFS401  Working Voltage  DC 5V~24V Maximum Working Current 15mA @ 5V DC Flow Rate Range 0.3~6L/min Connection 6mm (external diameter) Inlet Water Pipe Diameter 2.5-4mm Dimensions  5 x 4 x 3cms  Weight  15 grams

2 Inch Water Flow Sensor YF - DN50 The YF-DN50 water flow sensor is a device that is used to measure the flow rate of water. It consists of a turbine-type rotor that is placed in the water stream, and as the water flows past the rotor, it causes the rotor to spin. The sensor measures the speed of the rotor and converts it to a flow rate. The sensor has a digital output, which means that it provides a digital signal that can be read by a microcontroller or other host device. The sensor is commonly used in applications such as irrigation systems, water treatment plants, and industrial process control. It is often preferred over other types of flow sensors because it is easy to install and has a low cost. The YF-DN50 sensor is designed to be installed in a pipe with a diameter of 50mm or 1.97 inches. The YF-DN50 water flow sensor is a large 2 inch diameter Water Flow meter Sensor that can be used to measure flow rate from 10 - 200 Liter/min This water flow sensor consists of a plastic valve body, a rotor assembly and a Half effect current sensor. As the water flows through this sensor the rotor rotates and the speed of it changes with changes in the rate of flow of water. The hall-effect sensor outputs the corresponding pulse signal. The output of the flow sensor is proportional to the water flow. The more the water flowing more are the pulses.

1/2 Inch Brass Water Flow Sensor SEN-HZ21WI The SEN-HZ21WI water flow sensor is a device that is used to measure the flow rate of water. It consists of a turbine-type rotor that is placed in the water stream, and as the water flows past the rotor, it causes the rotor to spin. The sensor measures the speed of the rotor and converts it to a flow rate. The sensor has a digital output, which means that it provides a digital signal that can be read by a microcontroller or other host device. The sensor is commonly used in applications such as irrigation systems, water treatment plants, and industrial process control. It can easily measure water (liquid) flow in your application using this 1/2" Brass water flow sensor. This is a good quality flow sensor with a brass body and can be used for industrial and commercial applications. This half-inch water flow sensor is used extensively in various types of vending machines. Working of a Flow Sensor: The water flow sensor consists of a copper body, a water rotor, and a hall-effect sensor. When water flows through the rotor, the rotor rolls, its speed changes with different rates of flow. And the hall-effect sensor outputs the corresponding pulse signal. This water flow sensor is connected in line with the liquid whose flow rate has to be measured. There is a simple rotating wheel with a magnet and when the liquid flows the wheel is rotated and a hall effect sensor measures how many times the wheel is rotated and accordingly gives pulses. By counting the number of pulses you can easily calculate the flow rate as well as the amount of liquid dispensed. Note: When magnetic material is close to the sensor, its characteristics may vary. In order to avoid particle debris, the sensor must be installed after a filter. The flow sensor installation has to avoid strong vibration and shaking of the environment, so as not to affect the sensor's measurement accuracy. Applications: Widely used in water industrial fields Thermostatic water heaters Water purifiers Water dispensers Smart card equipment Coffee machines Electric hot water heater Gas water heater Instrument meter  Package Includes: 1 x SEN-HZ21WI Water Flow Sensor Specifications: Model  SEN-HZ21WI Water quality requirement Drinking water health standards, 0~80℃ Output level Rated voltage DC 5 Volt, high level ≥4.5 Volt, low level ≤ 0.5 Volt Flow characteristic F=10 Q-4, F: HZ, Q: L/min，±10% Cumulative flow conversion 1 Liter water = 553 pulses , accuracy: 10%

Float Switch Sensor For Water Level Controller With 2 Meter Wire A float switch sensor is a device that is used to detect the level of a liquid in a tank or container and control the flow of water based on the level. It consists of a float that is attached to a switch, and as the float rises or falls with the level of the liquid, it activates or deactivates the switch. The switch is connected to a control system, such as a water pump, via a 2 meter (6.6 feet) wire, and the control system is programmed to turn the pump on or off based on the state of the switch. Float switch sensors are commonly used in applications where the liquid level needs to be monitored or controlled, such as in sump pumps, water tanks, and overflow protection systems. They are often preferred over other types of level sensors because they are simple, reliable, and inexpensive. Float switch sensors may be used with liquids that are compatible with the materials used in the sensor, and they may have a maximum operating temperature and pressure rating. Used for detect the level of liquid within a tank. The switch may be used in a pump, an indicator, an alarm, or other devices.  read more : Beginner Guide to Float Switches How to Use - Insert the cable in the counter weight (Orange Color Part) from the conical part and rotate it. Thus causing the plastic ring inserted in the opening to become detached (if necessary this operation can be facilitated with the use of a screwdriver). The ring should then be positioned in the point where it is desired to block the counterweight. Force the counterweight on the ring by rotating it using slight pressure Advantages: Corrosion Free, Sturdy and durable & need no maintenance. No current / voltage is passed through water, therefore no electrolysis or Salt deposition. Long life (approximate 10 million operations) Rust proof (entire sensor body in polypropelene) Can be used in hard water or fuel such as diesel, kerosene, oil etc. Package Includes: 1 x Float Switch Sensor For Water Level Controller With 2 Meter Wire Specification: Rated voltage 250V Rated current 8A Mechanical endurance ≥100,000 times Electrical endurance ≥500,000 times Dimensions  11 x 9 x 5cms  Weight  690 grams

Water Flow Sensor - YF-B6 Flowmeter G3/4 1-30L/min 5-15V Brass Water Flow Sensor (Sea) YF-B6 is the perfect solution for industrial monitoring and water management systems. It is made with brass and plastic materials, measuring 60X OD26mm and featuring a G3/4 thread connection. The sensor includes a Hall effect sensor and digital output, ensuring accurate monitoring of flow rates. Its durable design makes it suitable for a wide range of conditions, perfect for industrial and commercial applications. Water Flow Sensor (Sea) YF-B6 is easy to install and maintain with its compact design. Perfect for engineers, technicians, and hobbyists. Water Flow Sensor (Sea) YF-B6 ensures the highest quality and durability. wire connection : Terminal 1  ( Red) : Vdd  ” + ” Terminal 2 (Black) Vout   ” – ” Terminal 3 ( Yellow )  Gnd : output (13) Connector :  Housing SM2.54-3P Package Includes:  1 x Water Flow Sensor - YF-B6 Flowmeter G3/4 1-30L/min 5-15V Brass Specifications: Material Brass Plastic Flow Sensor Sensor Hall effect sensor, Digital Output Size 60X OD26mm Thread Connection G3/4 Mounting Position Horizontal & Vertical Color Brass golden Flow Rate 1~30 L/min Flow Pulse F= 6.6 *Q ± 5%, Q=L/min Working Voltage DC4.5V ~ 24V Working Current 15mA Suffering Pressure Max 1.5Mpa Working Temperature -40 °C ~+80 °C Min Insulation Resistance 100M Ohm

1/2 Inch Water Flow Sensor - YF-S201 The YF-S201 water flow sensor is a device that is used to measure the flow rate of water. It consists of a turbine-type rotor that is placed in the water stream, and as the water flows past the rotor, it causes the rotor to spin. The sensor measures the speed of the rotor and converts it to a flow rate. The sensor has a digital output, which means that it provides a digital signal that can be read by a microcontroller or other host device. The sensor is commonly used in applications such as irrigation systems, water treatment plants, and industrial process control. It is often preferred over other types of flow sensors because it is easy to install and has a low cost. Water flow sensors are installed at the water source or in pipes to measure the rate of flow and calculate the amount of water that has passed through the pipe. Water flow is measured in liters per hour or cubic meters. Working: A water flow sensor is made up of a plastic valve through which water can pass. A water rotor and a hall effect sensor are used to sense and measure the flow of water. When water flows through the valve, it causes the rotor to rotate. The motor's speed can be changed as a result of this. The hall effect sensor calculates this change and outputs it as a pulse signal. The rate of flow of water can thus be measured. The Hall effect is the primary operating principle of this sensor. The rotation of the rotor induces a voltage difference in the conductor in this sensor, according to this principle. This induced voltage difference runs in the opposite direction of the electric current. When the moving fan rotates due to the flow of water, the rotor rotates, inducing a voltage. The hall effect sensor measures the induced voltage and displays it on the LCD display. read more : What is a Water Sensor? The water flow sensor can be used with hot, cold, or warm water, as well as clean or dirty water. A microcontroller board such as Arduino , Raspberry pi, a LCD display or OLED Display , Breadboard and connecting wires are required for this. The sensor is installed at the water source inlet or the pipe opening. Three wires are connected to the sensor. The red wire connects to the supply voltage. A black wire connects to the ground, and a yellow wire collects the Hall effect sensor output. 5V to 18V DC is required for supply voltage. Also, read our blog on the Water Level Sensor explaining the different types of water sensors, working, and applications. Connection details: Red wire : +5V Black wire : GND Yellow wire : PWM output.

Float Switch Long Shaft Float Level Switch SEN-PPI150 is the ideal solution for accurately measuring liquid levels. Crafted with advanced Plastic PP material, this switch guarantees durability and longevity. The customizable specifications allow you to tailor the wire harness, float dimensions, warning points, and switching power to meet your specific needs. This cutting-edge technology includes a switching signal for precise liquid level detection, making it suitable for water dispensers, humidifiers, water air conditioning, air conditioning fans, and more. The DC2000V voltage and ≤0.5A electric current provide endless possibilities for water-related activities, making it perfect for users of all skill levels and ages. Designed with reliability in mind, the SEN-PPI150 is crafted with high-quality Plastic PP material, ensuring it thrives in ideal conditions. With various sizes and color options, this float level switch caters to diverse preferences. Float Level Switch is not just a product; it's a solution. It's easy to use and maintain, thanks to its user-friendly design and unique features that address common customer pain points. Whether for households, commercial spaces, or industrial settings, this switch is the go-to choice for accurate liquid level measurement Applications: Water Dispenser, Humidifier, Water Air Conditioning, Air Conditioning Fan, etc. Package Includes: 1 x Float Switch Long Shaft Specifications: Material Plastic PP Switching Signal Yes Temperature Range 0-60 Deg C Voltage/Electric Current DC2000V, ≤0.5A

1/2 Inch Water Flow Sensor SEN-HZ21WA The SEN-HZ21WA water flow sensor is a device that is used to measure the flow rate of water. It consists of a turbine-type rotor that is placed in the water stream, and as the water flows past the rotor, it causes the rotor to spin. The sensor measures the speed of the rotor and converts it to a flow rate. The flow sensor has a digital output, which means that it provides a digital signal that can be read by a microcontroller or other host device. The sensor is commonly used in applications such as irrigation systems, water treatment plants, and industrial process control. It is often preferred over other types of flow sensors because it is easy to install and has a low cost. The SEN-HZ21WA sensor is designed to be installed in a pipe with a diameter of 1/2 inch (12.7mm). A pinwheel inside the sensor moves as the liquid flows through the sensor. A hall effect sensor within the sensor senses the rotation of the pinwheel and outputs a digital pulse for every rotation. By counting the pulses from the sensor, you can easily sense liquid flow through the sensor. This allows easy interface to microcontroller, Arduino, Raspberry Pi, etc. Applications: Water testing Water cooling systems Measure liquid flow Package Includes: 1 x Water Flow Sensor SEN-HZ21WA Specifications: Sensor Type  Water Flow Sensor  Model  SEN-HZ21WA Test range 1~30L/min(m³/h) Max. Working current 15mA Working Voltage  DC 5V Working pressure 1.75MPa Hysteresis 0.01(%F.S.) Insulativity Insulation Resistance≥100MΩ Dimensions  57.8*37*37mm, G1/2 outside diameter Weight  25 grams

1/4 Inch Brass Water Flow Sensor SEN-HZ41WC The SEN-HZ41WC water flow sensor is a device that is used to measure the flow rate of water. It consists of a turbine-type rotor that is placed in the water stream, and as the water flows past the rotor, it causes the rotor to spin. The sensor measures the speed of the rotor and converts it to a flow rate. The sensor has a digital output, which means that it provides a digital signal that can be read by a microcontroller or other host device. The sensor is commonly used in applications such as irrigation systems, water treatment plants, and industrial process control. It is often preferred over other types of flow sensors because it is easy to install and has a low cost. Now easily measure water (liquid) flow in your application using this 1/4" Brass water flow sensor. This is a good quality flow sensor with a brass body and can be used for industrial and commercial applications. This 1/4 inch water flow sensor is used extensively in various types of vending machines. Note: When magnetic material is close to the sensor, its characteristics may vary. In order to avoid particle debris, the sensor must be installed after a filter. The flow sensor installation has to avoid strong vibration and shaking of the environment, so as not to affect the sensor's measurement accuracy. Applications: Widely used in water industrial fields Thermostatic water heaters Water purifiers Water dispensers Smart card equipment Coffee machine Package Includes: 1 x SEN-HZ41WC Water Flow Sensor Specifications: Water quality requirement Drinking water health standards, 0~80℃ Voltage/electric current DC 4.5 ～ 18 Volt, ≤15mA Output level Rated voltage DC 5 Volt, high level ≥4.5 Volt, low level ≤0.5 Volt Cumulative flow conversion 1 Liter water=1780 pulse, accuracy: 8%

Turbidity Sensor Module Kit The Turbidity Sensor emits at its end an infrared light, imperceptible to human vision, capable of detecting particles that are suspended in water, measuring the light transmittance and the dispersion rate, which changes according to the Amount of TSS (Total Suspended Solids), increasing the turbidity of the liquid whenever levels increase.This is a Turbidity Sensor Module, an electronic monitoring module specially developed to work with microcontroller platforms Arduino, Raspberry Pi, PIC, ARM, AVR, among others. It is very efficient, the Arduino Turbidity Sensor is able to detect and verify the quality of the water, making the turbidity measurement, where it is possible to verify the results by means of digital or analogue signal next to the corresponding pins in the accompanying electronic module. In general, the Arduino Turbidity Sensor is applied in projects involving the monitoring of water turbidity in rivers, streams, lakes, water bodies, catchment and research sites, laboratories, tanks with liquids and so on. This Turbidity Sensor has an end specially prepared for direct contact, having an electronic module to amplify and send the received data to the microcontroller of the project. Package Includes:  1 x Turbidity Sensor Set Turbidity Sensor Specifications: Working voltage 5V DC Current 30mA (MAX) Operating temperature -30 ° C to 80 ° C Compatible Arduino, Raspberry Pi, AVR, PIC Measuring Range 0 ~ 1000 NTU Dimensions  5 x 5 x 5 cms  Weight  50 grams