Cytron Maker Pi RP2040 – Robotics Controller Board with Raspberry Pi

Female to Female Jumper Wires (20cm) 40pcs These are 20cm 40pcs Female to Female Jumper wires, very Flexible and easily detachable. These jumper cables have 1Pin female to the 1pin female header with both ends. Also, it is compatible with 2.54 mm mil spacing pin headers. This cable is an electrical wire or group of them in a cable with a connector or pins at each end, which is normally for interconnecting the components of a breadboard or other prototype or test circuit, internally or with other equipment or components, without soldering. Individual Dupont Cables are fitted by inserting their end connectors into the slots provided in a breadboard, the header connector of a circuit board, or a piece of test equipment. Mostly Dupont cables are useful with Orange Pi, Banana Pi, Raspberry Pi , Arduino , and other mini PCs and development boards . It is very useful in the PCB project, PC motherboard, as well as Breadboard connections. Additionally, these jumper wires allows you to plug and unplug easily for prototyping and can be used over and over again. Check out the best selection of Jumper Wires . Applications: Raspberry Pi Arduino PCB projects Breadboard connections Get a complete set of M2M, M2F, F2F Jumper Wires Set for DIY projects.

A3967 Stepper Motor Driver This A3967 Stepper Motor Driver For Arduino is the most recent version of EasyDriver v44, which was created in collaboration with Brian Schmalz. When compared to previous versions, it offers more flexibility and control over your stepper motor . It is a simple stepper motor driver that is compatible with most microcontrollers and capable of producing a digital 0 to 5V pulse (0 to 3.3V pulse if you solder SJ2 closed on the EasyDriver). A 7V to 30V power supply is required for the module's motor. The digital interface is powered by an onboard voltage regulator that can be set to 5V or 3.3V. The A3967 is a full-featured microstepping motor driver with an integrated transistor. It is intended for use with bipolar stepper motors in full-, half-, quarter-, and eighth-step modes, with output drive capabilities of 30 V and 750 mA. The A3967 comes with a fixed off-time current regulator that can operate in slow, fast, or mixed current-decay modes. This current-decay control scheme produces less audible motor noise, higher step accuracy, and lower power dissipation. The transistor is essential to the A3967's simple implementation. Simply sending one pulse to the STEP input causes the motor to move one step (full, half, quarter, or eighth depending on two logic inputs). It is not necessary to programme phase-sequence tables, high-frequency control lines, or complex interfaces. The A3967 interface is ideal for applications where a complex P is either unavailable or overburdened. Features: A3967 microstepping driver Adjustable current control from 150mA/phase to 750mA/phase MS1 and MS2 pins are broken out to change microstepping resolution to full, half, quarter and eighth steps (defaults to eighth) Compatible with 4, 6, and 8-wire stepper motors of any voltage Breadboard-compatible pins.

Official Raspberry Pi 4 Model B 4GB RAM The Raspberry Pi 4 Model B 4GB is a compact and versatile single-board computer that provides desktop-level performance in a credit card-sized device. The RPI 4B is powered by a Broadcom Quad-Core Cortex-A72 (ARM v8) 64-bit SoC that runs at 1.5GHz and has 4GB of LPDDR4-3200 SDRAM for efficient multitasking and basic desktop programs. This device is designed for a wide range of DIY projects, including media centres, file servers, robotics, and smart home systems. The Raspberry Pi 4B 4GB supports dual 4K displays ( 4K@30Hz ) through its micro-HDMI ports, making it perfect for high-definition video and creative endeavours. It has dual-band WiFi 2.4 GHz and 5.0 GHz IEEE 802.11ac , Bluetooth 5.0 , and Gigabit Ethernet for a consistent connection. It also features two USB 3.0 connections and two USB 2.0 ports to connect devices. The Raspberry Pi 4 4GB is popular among programmers and makers. It comes with native Python support , making it a fantastic platform for coding education and automation project development. It is capable of running both 32-bit and 64-bit operating systems , offering versatility for different uses. Whether for teaching, prototyping, or creative projects, it serves as a potent and affordable computing option. Shop Raspberry Pi 4 4GB Full Kit – Plug & Play Setup Affordable power for your projects – Raspberry Pi 4 2GB ! What makes this model Great? The speed and performance of the new Raspberry Pi 4 4GB are a noticeable improvement from earlier models. For the first time, the Raspberry Pi Foundation has created a complete desktop experience. Whether you're editing documents, browsing the web with multiple tabs open, managing spreadsheets, or creating a presentation, you'll find the experience smooth and familiar. It is a more energy-efficient and cost-effective machine. Features Broadcom 2711 Quad-Core Cortex A72 @ 1.5GHz delivers 20% faster performance with improved power and thermal efficiency. Dual micro-HDMI outputs support dual 4K displays with hardware video decode at 4Kp60 (H.265, H.264, MPEG-4). Dual-band WiFi (802.11b/g/n/ac) on 2.4GHz & 5GHz with advanced PCB antenna for robust wireless connectivity. Bluetooth 5.0 offers an extended range of wireless peripherals. Upgraded USB 3.0 Ethernet provides wired speeds up to 10x faster than previous models. 2 USB 3.0 and 2 USB 2.0 ports enable versatile peripheral connections. 40-pin GPIO header is fully backwards-compatible with earlier Pi models. Optional PoE support is available, with PoE header pins designed to work with proper standoffs. Comparison Table Raspberry Pi 4 Model B Raspberry Pi 5 Raspberry Pi 3 Model B+ Price (INR) ?3599 VIEW ?5129 VIEW ?3649 VIEW Processor 1.5GHz Quad-Core ARM Cortex-A72 2.4GHz Quad-Core ARM Cortex-A76 1.4GHz Quad-Core ARM Cortex-A53 RAM 1GB, 2GB, 4GB, 8GB LPDDR4 2GB, 4GB, 8GB, 16GB LPDDR4 1GB LPDDR2 Wi-Fi Dual-band 802.11ac Dual-band 802.11ac Dual-band 802.11ac Bluetooth 5.0 5.0 4.2 USB Ports 2× USB 3.0, 2× USB 2.0 2× USB 3.0, 1× USB 2.0 4× USB 2.0 Ethernet Gigabit Ethernet Gigabit Ethernet Gigabit Ethernet Video Output 2× Micro HDMI (4Kp60) 2× Micro HDMI (4Kp60) 1× HDMI (1080p) GPIO Pins 40 40 40 Storage MicroSD (SDXC up to 2TB) MicroSD (SDXC up to 2TB) MicroSD (SDHC) Power Supply USB-C USB-C Micro USB Click for Complete Raspberry Pi Kits – Learn, Build, and Innovate! Pin Diagram:

CNC Shield for Arduino The CNC shield for Arduino has total four slots, can drive 4 A4988 stepper motors. Each road stepper motors only need two IO ports. In other words, six IO ports can be well managed three stepper motors. The CNC Shield V3.0 allows you to build a engraving machine, 3D printer, mini CNC and other similar devices using your Arduino. It is designed as a shield and can plug on top of an Arduino requiring no external connections and wiring. There are 4 slots on the board for plugging in stepper motor drive module which can drive 1 stepper motor each. Controlling each step stepper motor requires only two IO pins on the Arduino. Just insert this Arduino CNC Shield V3.0 onto an Arduino UNO , and install the GRBL firmware, you can then quickly build a DIY CNC engraving machine. This arduino shield is very convenient to use and is suitable for development boards compatible with Arduino. This CNC shield compatible with Arduino is the latest version of the CN shield model (V 3.0). The CNC Shield is GRBL 0.9 compatible and with the help of jumper wires , it is accessible to stepper drivers. Features: Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place. GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals) 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)

CNC Shield + UNO R3 Board compatible with Arduino + 4xDRV8825 Driver Kit Arduino Uno is an open-source microcontroller used by students and hobbyists entering the world of DIY electronics and automation, The Arduino Uno can be used for any application including being the brains of your next DIY 3D printer and/or CNC router The CNC Shield V3.0 allows you to build an engraving machine, 3D printer, mini CNC and other similar devices using your Arduino. It is designed as a shield and can plug on top of an Arduino requiring no external connections and wiring. Along with that, the CNC shield allows you to control up to four stepper motors by mounting on 4 stepper motor drivers, included with this kit The DRV8825 provides an integrated motor driver solution for printers, scanners, and other automated equipment. The device has two H-bridge and is intended to drive a bipolar stepper motor. Features: UNO R3 Board: The main microcontroller board compatible with Arduino. CNC Shield: An expansion board that allows for easy connection and control of stepper motors. 4x DRV8825 Stepper Motor Drivers: High-performance drivers for controlling stepper motors. Micro-Stepping: Supports micro-stepping settings for precise control of stepper motors. GRBL Compatibility: Compatible with GRBL firmware, which is widely used for CNC control. Voltage Range: Operates on 12-36V DC. Heat Sinks: Included for cooling the stepper motor drivers. USB Cable: For connecting the UNO R3 board to a computer. 40-Pin Row Needles: For additional connections. Applications: CNC Machines: Used for controlling stepper motors in CNC milling, engraving, and cutting machines. 3D Printers: Essential for driving stepper motors in 3D printers, ensuring precise layer deposition and movement. Laser Cutters: Controls stepper motors in laser cutting machines for accurate cutting and engraving. Robotics: Ideal for robotics projects requiring precise motor control, such as robotic arms and automated guided vehicles (AGVs). X-Y Tables: Used in X-Y tables for accurate positioning and movement in various industrial applications. Pick-and-Place Devices: Employed in pick-and-place machines for accurate component placement in electronics manufacturing. Labeling Machines: Used in labeling machines for precise label application. Pinout Diagram for the Arduino Uno Microcontroller Applications of the Kit The kit can be used to create custom 3D printers, scanner, CNC mills and other automated equipment applications

Waveshare 3.5inch Capacitive Touch LCD IPS Display Module 320×480 The Waveshare 3.5-inch Capacitive Touch LCD IPS Display Module is a compact yet powerful display solution featuring a 320 × 480 pixel resolution that delivers crisp visuals and excellent clarity. Designed with an IPS panel, it offers wide viewing angles and consistent color performance, making it ideal for graphical interfaces and interactive applications. The module integrates the ST7796S display driver for reliable display control and the FT6336U capacitive touch controller for accurate, multi-touch responsiveness. Optimized for embedded development, this 3.5 inch LCD Raspberry Pi display is perfectly suited for Raspberry Pi projects, control panels, and custom HMI applications where space, touch precision, and visual quality matter. Features: 320×480 resolution, 262K colors, clear and colorful displaying effect High touch screen transmittance, fast response and long lifetime Embedded with ST7796S driver chip and FT6336U capacitive touch control chip, using SPI and I2C communication respectively, minimizes required IO pins Onboard TF card slot for storing more pictures, videos, music, etc. Adapting 15PIN connector and 18PIN FPC slot for connecting the LCD module to the host board Onboard voltage translator, compatible with 3.3V / 5V operating voltage Comes with online development resources and manual (examples for Raspberry Pi / ESP32 / Raspberry Pi Pico / Arduino) SPI and I2C Control Interfaces: Pin Description 15PIN Pin No. 18PIN Pin No. VCC Power (3.3V / 5V input) 1 1 3V3 Power (3.3V input) 2 NC GND Ground 3 3 MISO SPI MISO pin 4 6 MOSI SPI MOSI pin 5 5 SCLK SPI CLK pin 6 4 SD_CS TF card chip selection, low active 7 10 LCD_CS LCD chip selection, low active 8 9 LCD_DC LCD data/command selection (high for data, low for command) 9 7 LCD_RST LCD reset pin, low active 10 8 LCD_BL LCD backlight pin 11 2 TP_SDA Touch panel data pin 12 14 TP_SCL Touch panel clock pin 13 13 TP_INT Touch panel interrupt pin 14 15 TP_RST Touch panel reset pin, low active 15 12

Cytron URC10 Sumo Robot Controller R1.1 Arduino-Compatible Motor Driver Board The Cytron URC10 Sumo Robot Controller R1.1 is a powerful all-in-one robotics control board designed specifically for competitive sumo robot building. It combines an Arduino-compatible ATmega328P microcontroller, a dual 10A motor driver, and dedicated interfaces for ultrasonic, digital, and analog sensors - making it one of the most efficient and beginner-friendly solutions for robot builders. With support for 8V–25V DC motors, 30A peak current, and high-frequency PWM control, this controller ensures strong pushing power and fast maneuverability for 3kg sumo robot competitions. Cytron engineered the URC10 to simplify robot development by integrating essential hardware like built-in test buttons, motor output LEDs, onboard 5V/3.3V regulators, and a Micro-USB interface for programming. Whether you're designing autonomous systems, competitive sumo robots, or experimenting with robotics, the Cytron URC10 offers reliable performance, stable motor control, and easy sensor expansion for both beginners and advanced makers. Features: Designed specifically for up to 3kg sumo robot applications. Built around the Arduino-compatible ATmega328P microcontroller with Optiboot Bootloader. Integrated dual 10A continuous motor driver (30A peak per channel) for high-power brushed DC motors. Supports 8V–25V motor voltage for a wide range of robot motors. Features current limiting at 30A per channel for safe operation under heavy loads. Includes motor test buttons for quick verification without uploading code. Motor output status LEDs for easier debugging and inspection. Compatible with sign-magnitude and locked-antiphase PWM, supporting up to 20kHz frequency. Onboard 5V, 1A regulator and 3.3V, 500mA regulator for powering sensors and modules. Dedicated pins for motors, ultrasonic sensors, digital I/O, and analog sensors. Includes USB Micro-B + CH340 USB-serial system for easy programming upload. Provides 1× I2C port for additional modules. Compact design with dimensions 75.57mm × 99.7mm. Note: Reverse polarity protection is not included.

SmartElex 5V 3A 4 Channel Signal Relay Module The SmartElex 5V 3A 4 Channel Signal Relay Module is a compact and reliable 4 Channel Relay Module designed to control four independent medium-power loads with precision. Powered as a 5V relay module, it integrates high-quality JY4100F-S-DC5V-C relays, each capable of switching up to 3A at 120V AC or 24V DC. With dedicated trigger inputs and LED status indicators for every channel, it allows easy monitoring and accurate switching. This module directly interfaces with popular microcontrollers such as Arduino, ESP8266, and Raspberry Pi, making it ideal for IoT, home automation, and embedded control applications where safety, isolation, and consistent performance are essential. Applications: Home automation (controlled lights, fans, and locks) Industrial machine control IoT multi-device projects. Robotics and Motor Control Security systems and alarms. Cautions: Always utilize a properly regulated 5V power supply. Avoid exceeding the rated load capacity. Provide proper isolation for AC loads. Store the module in a dry, clean place. Features: Four-channel relay module allows for independent control of four devices. Operates at 5V DC and has an active LOW/HIGH trigger. Each relay can handle up to 3A at 120V AC or 24V DC. Compatible with Arduino, ESP8266, Raspberry Pi, and more platforms. Each channel has its own set of LED indicators. Fast switching: ≤10 ms operation and ≤5 ms release time. Low contact resistance (≤100 mΩ) ensures effective operation. The total power consumption is around 1.44W over four channels. High insulation resistance and dielectric strength are essential for safety. Wide operational temperature range (-40°C to +85°C).

SmartElex 12V 20A Single Channel Power Relay Module The SmartElex 12V 20A Single Channel Power Relay Module is a high-current switching solution designed to control heavy electrical loads using low-voltage control signals. It helps safely operate high-power devices without directly exposing microcontrollers or control circuits to high current, reducing risk and improving system reliability. This module is suitable for students, makers, engineers, educators, and startups who are working on power control, automation, or embedded electronics projects that demand robust switching capability. This single channel power relay module is ideal for robotics, IoT systems, home and industrial automation, and power management applications where devices such as motors, heaters, pumps, or high-load appliances need reliable control. It can be easily interfaced with popular platforms like Arduino, Raspberry Pi, and ESP32, making it convenient for both prototyping and deployment. The strong build quality and straightforward integration make it a dependable choice for projects requiring consistent and safe high-current switching. Features: Single channel power relay module for high-current load control Operates on 12V, suitable for industrial and automation systems Supports heavy load switching up to 20A Electrical isolation between control and power circuits for safety Compatible with Arduino, Raspberry Pi, ESP32, and similar controllers Robust design for reliable operation in power control applications

Waveshare UGV Rover ROS 2 Open-source 6 Wheels 4WD AI Robot Suitable for Raspberry Pi 4B / Raspberry Pi 5 Dual controllers, All-metal Body, Flexible and Expandable The UGV Rover ROS 2 Open-source 6-Wheel 4WD AI Robot is a robust, all-metal mobile robotics platform designed for versatile development and real-world navigation. Featuring dual controllers, a flexible and expandable chassis, and seamless ROS 2 integration, it delivers reliable performance for autonomous tasks and intelligent robotics projects. Compatible with Raspberry Pi 4B and Raspberry Pi 5, this rover is perfect for learners, innovators, and developers looking to build advanced AI robotics systems with powerful hardware and modular expandability. Features Supports Pan-Tilt drag-and-drop control via mouse or touch panel of the laptop, providing a better control experience as FPS games Based on Raspberry Pi Designed to support both Raspberry Pi 5 and Raspberry Pi 4B, this robot leverages the strong computing capabilities of the Pi ecosystem to handle more complex tasks with ease. Its expandable architecture unlocks more possibilities for AI, automation, and ROS 2 development. Advanced AI Recognition & Tracking Based on OpenCV, supports color recognition and automatic targeting with one-key Pan-Tilt control and auto LED lighting. Expandable for additional AI functions. Face Detection & Recognition Automatically captures photos or records videos when a face is detected, providing enhanced security and AI interaction. Cross-Platform Web Control No app installation required! Simply connect via a web browser on mobile, tablet, or PC. Supports WASD keyboard shortcuts and mouse control for seamless navigation. WebRTC real-time video transmission Adopts Flask lightweight web application, based on WebRTC ultra-low latency real-time transmission, using Python language and easy to extend, working seamlessly with OpenCV Features at a glance Multiple Autonomous Navigation Modes UGV Rover supports multiple autonomous navigation modes, allowing it to navigate complex environments with precision. Whether following predefined paths, avoiding obstacles, or performing AI-assisted route planning, the robot adapts intelligently to real-world terrains.

7Semi SHT40 Temperature & Humidity Sensor Breakout I2C Qwiic SHT40 Breakout (ES-13514) The 7Semi SHT40 Temperature & Humidity Sensor Breakout (I2C Qwiic) is a compact and reliable sensor module designed to measure both temperature and humidity with high accuracy. It is based on the Sensirion SHT40 sensor, making it suitable for modern electronics projects that need precise environmental data. This breakout board supports I2C communication and comes with a Qwiic connector, allowing quick and solder-free connections with microcontrollers like Arduino, ESP32, and Raspberry Pi. Its small size and low power consumption make it ideal for IoT devices, weather monitoring, indoor air quality projects, and learning applications where simplicity and accuracy matter. Features: High-accuracy temperature and humidity sensing using the SHT40 sensor Supports I²C communication for easy integration with microcontrollers Qwiic connector enables quick, solder-free plug-and-play connections Wide measurement range of 0–100% RH and –40°C to +125°C temperature Low-power and compact design, ideal for IoT and battery-powered projects Compatible with Arduino, Raspberry Pi, ESP32, and other development boards SHT40 Board Dimensions

SmartElex NS612 PIR Motion Sensor Module The SmartElex NS612 PIR Motion Sensor Module is a passive infrared motion detection solution designed to sense human movement by detecting changes in infrared radiation. It helps automate systems by triggering actions only when motion is detected, reducing unnecessary power usage and improving system efficiency. This module is suitable for students, makers, engineers, educators, and startups working on electronics projects that require reliable and responsive motion sensing for security, automation, or interactive applications. This PIR motion sensor module is widely used in robotics, IoT devices, security systems, and home or industrial automation projects where motion detection is essential. It can be easily interfaced with popular development platforms such as Arduino, Raspberry Pi, and ESP32, allowing quick integration into prototypes and working systems. The dependable performance and simple interface make it ideal for applications like motion-activated lighting, alarm systems, smart monitoring solutions, and embedded electronics projects. Features: Passive infrared (PIR) sensor for accurate human motion detection Detects movement by sensing changes in infrared radiation Long sensing range suitable for wider coverage areas Low power consumption for battery-powered applications Digital output for easy interfacing with microcontrollers Compatible with Arduino, Raspberry Pi, ESP32, and similar boards

Cytron SHIELD-3AMOTOR 1.2A Dual Channel 7V–30V DC Motor Driver Shield for Arduino The Cytron SHIELD-3AMOTOR is a high-performance, dual-channel DC motor driver shield designed for Arduino users who need reliable and efficient motor control. Supporting motor voltages from 7V to 30V and delivering up to 3A peak and 1.2A continuous current per channel, this shield is ideal for robotics, automation, DIY RC vehicles, and mechatronics projects. Its compatibility with Arduino UNO, Mega, Leonardo, Zero, 101, and other popular boards makes it a plug-and-play solution for both beginners and advanced makers searching for powerful motor-driving capabilities. Built using the DRV8871 motor driver IC, the Cytron SHIELD-3AMOTOR supports both Signed Magnitude and Locked Anti-Phase control modes via an easy DIP switch selector. Additional features such as current limit protection, stackable headers, quick-test pushbuttons, and direct connectors for the LSS05 auto-calibrating line sensor make this shield perfect for building reliable robot platforms, line-followers, and dual-motor systems. With strong motor handling and seamless Arduino integration, this Cytron shield makes high-current motor control simple, safe, and efficient. Features: Dual-channel brushed DC motor driver shield designed for full Arduino compatibility. Supports 7V–30V motor voltage, suitable for a wide range of DC motors. Handles 3A peak and 1.2A continuous current per channel, ideal for medium-power robotic applications. Built-in current limit protection for safer motor operation. Compatible with 3.3V and 5V logic input, supporting various Arduino boards. DRV8871 IC ensures smooth, efficient, and reliable motor control. Selectable control modes: Signed Magnitude and Locked Anti-Phase via DIP switches. Stackable header pins for easy integration with additional shields. Quick-test switches provided for rapid motor testing on both channels. Includes dedicated connector for Cytron LSS05 Line Sensor, ideal for line-following robots. (Note: No polarity protection for motor supply input - connect with care.)

Cytron Maker UNO Plus – Arduino-Compatible Educational Board The Cytron Maker UNO Plus is a beginner-friendly, Arduino-compatible development board designed to simplify electronics and coding for students, educators, and STEM hobbyists. With onboard LEDs, a built-in piezo buzzer, a programmable pushbutton, and upgraded components, this board removes wiring complexity allowing learners to focus on coding, debugging, and hands-on exploration. Whether used for school projects, robotics, or microcontroller education, the Cytron Maker UNO Plus ensures a smooth and frustration-free learning experience. Thanks to its pre-labeled pin headers, Micro USB connectivity, and fully Arduino-compatible architecture, setup becomes effortless for new users. Students can instantly code and visualize real-time pin activity through indicator LEDs, making debugging easier and more intuitive. The Cytron Maker UNO Plus is ideal for classroom teaching, STEM labs, maker workshops, and hobby projects, helping learners jump straight into creating fun electronics projects like light sequences, melodies, and interactive displays. Features: Fully compatible with Arduino ecosystem, sharing all libraries and example codes. Integrated 12× onboard LEDs for simplified debugging and visual learning. Built-in piezo buzzer and programmable pushbutton for interactive projects without extra wiring. Upgraded 3.3V line provides 500mA output to support more sensors and modules. Micro USB interface replaces bulky USB Type-B for universal connectivity. Uses FT231X USB-to-Serial converter for easier and more reliable driver installation. Includes pin-header label stickers for effortless classroom identification. CE, FCC & RoHS compliant - safe, environmentally friendly, and education-ready. Students can write their names directly on the board to avoid mix-ups.

Official Arduino UNO Q SBC 4GB ABX00173 The Arduino UNO Q SBC 4GB ABX00173 is a powerful and humanized dual-brain development platform designed to seamlessly bridge high-performance computing with real-time control. Featuring a Linux® Debian-capable Qualcomm® Dragonwing™ QRB2210 microprocessor alongside a real-time STM32U585 microcontroller (MCU), this 4GB variant delivers enhanced memory capacity for demanding AI-driven applications. Whether you're building systems for object recognition, voice commands, motion detection, or other intelligent edge applications, the Arduino UNO Q 4GB provides the perfect balance between a full-fledged single-board computer and precise microcontroller control. It’s not just Arduino—it’s a complete innovation platform ready to power your next advanced project. This edition of Arduino UNO Q has 4 GB of RAM and 32 GB of eMMC, making it the best choice if: You plan to use UNO Q in single-board computer (SBC) mode. Your application requires numerous high-level processes to execute at the same time. You intend to use larger, more complex AI or machine learning models (such as high-resolution computer vision or advanced audio processing). You'll need enough of built-in storage for logs and data, as well as a strong development environment. The Arduino UNO Q is the ideal tool for prototyping your next robotics or IoT project because: All-in-One Toolbox: The Arduino UNO Q is a versatile tool that combines the Dragonwing™ QRB2210 microprocessor (MPU) with a real-time STM32U585 microcontroller (MCU), making it ideal for any project. AI in a blink: Discover AI-powered vision and sound solutions that respond to their surroundings. Millions of Arduino users have created libraries, sketches, and projects for the UNO ecosystem. Compatible with the Arduino UNO ecosystem: UNO Q is compatible with a wide range of Arduino hardware, including old UNO shields and new carriers, as well as Modulino® nodes and third-party modules via the Qwiic connector. Streamlined software experience: In addition to the Arduino IDE and Arduino Cloud, you can get started with a plethora of pre-built examples and AI models available through Arduino App Lab. Seamless, unified development: create classic Arduino Sketches, code in Python® using the pre-installed Linux® Debian OS, or combine the two from a single interface - easy with Arduino App Lab. What is the Arduino App Lab? Unified Developer Experience App Lab is a brand-new comprehensive development environment that unifies the journey from Linux® to real-time OS. Preloaded on the UNO Q, App Lab combines Arduino Sketches, Python® scripts, and containerized AI models to create fully integrated applications that can be administered from a single interface. Ready-to-use Apps and Bricks Get started quickly with Arduino Apps, self-contained examples that include everything you need. Add plug-and-play capabilities to your projects using pre-built Bricks to help you push your ideas even further. Pre-loaded AI models With pre-loaded AI models in Arduino App Lab, you can use real-world data for a variety of tasks, including object/human detection, anomaly detection, image categorization, sound recognition, and keyword spotting. Find out more in the official documentation . Features: Microprocessor: Qualcomm® Dragonwing™ QRB2210 Microcontroller: Real-time, low-power STM32U585 MCU RAM: 4 GB LPDDR4 Storage: 32 GB eMMC built-in (no SD card required) Connectivity: Dual-band Wi-Fi® 5 (2.4/5 GHz), Bluetooth® 5.1 High-speed headers: Power advanced peripherals – vision, audio, display Classic UNO headers: Mount shields to add capabilities LED matrix: 8 x 13 LED matrix for visual creation and feedback USB-C connector: Power delivery, video output, or connect keyboard, mouse, USB microphones or USB cameras via dongle Qwiic connector: Expand easily with Modulino® nodes – no soldering required