100K ohm NTC 3950 Thermistor The 3950 NTC Thermistor is a thermally sensitive resistor and the special feature of these 100K ohm thermistors is that they exhibit a large change in resistance with only a small change in temperature. The thermistor is ideally used as a temperature sensor for 3D Printer Reprap. NTC is also known as the Negative Temperature Coefficient. These thermistors are widely used as inrush current limiters, temperature sensors, self-resetting overcurrent protectors, and self-regulating heating elements. This Thermistor 100k NTC with 1 Meter Cable Temperature Sensor for 3D Printer Reprap. The thermistor is a thermally sensitive resistor known for exhibiting a large change in resistance with only a small change in temperature. It is important to note that a thermistor's change in resistance is non-linear. It follows a pre-defined curve which is provided by the thermistor manufacturer. Positive thermal coefficient (PTC) will increase in resistance with an increase in temperature, and negative ones (NTC) will decrease. But the formula in practice is not linear, so sometimes an accurate table of measurements is better than the linear formula.

10K Thermistor Temperature Sensor Module(3 Pin) Thermistor Temperature Sensor Module is very sensitive to ambient temperature. This electronic part generally used to detect the temperature of the surrounding environment. Through potentiometer adjustment, it is possible to change the temperature detection threshold. DO output can be directly connected to the microcontroller to detect high and low, by detecting temperature changes in the environment. The temperature detection range of the module is between 20 and 80 degrees Celsius. This sensor module can be replaced with a line temperature sensor for controlling the water temperature, water tank, etc. Generally, the 4-wire method of thermistor measurement is the most accurate because there is effectively no current flowing in either of the measurement cable wires and therefore no added resistance due to the cable wires. Also check the DC 3-5V MAX6675 Module + K Type Thermocouple Temperature Sensor Thermocouple Sensor Set M6 Screw and Jumper Wire F to F 5pcs

10K Temperature Sensor (Thermistor) A 10K temperature sensor (also known as a thermistor) is a type of resistor that changes its resistance value in response to changes in temperature. The "10K" refers to its resistance value at a temperature of 25°C, which is 10,000 ohms. Thermistors are commonly used in temperature sensing and control applications because of their high sensitivity and fast response time. They are often preferred over other temperature sensors such as thermocouples and RTDs because they are smaller, cheaper, and easier to use. There are two main types of thermistors: negative temperature coefficient (NTC) and positive temperature coefficient (PTC). NTC thermistors have a resistance that decreases as the temperature increases, while PTC thermistors have a resistance that increases as the temperature increases. Thermistors are inexpensive, easily obtainable temperature sensors.  They are easy to use and adaptable.  Circuits with thermistors can have reasonable output voltages - not the millivolt outputs thermocouples have.  Because of these qualities, thermistors are widely used for simple temperature measurements.  They're not used for high temperatures, but in the temperature ranges where they work, they are widely used. Applications: Temperature control in HVAC systems Medical equipment Industrial processes Automotive systems Environmental monitoring Consumer electronics. Also check 10K Thermistor Temperature Sensor Module(3 Pin) Also check 10K Thermistor Temperature Sensor Module(4 Pin) . The module is small and low-cost. It can be used to detect the temperature of the surrounding environment.

10K Thermistor Temperature Sensor Module(4 Pin) The 10K NTC Thermistor temperature sensor module is a low-cost, small-size module. It is very sensitive to ambient temperature. It is generally used to detect the temperature of the surrounding environment. Through potentiometer adjustment, it is possible to change the temperature detection threshold. DO output can be directly connected to the microcontroller to detect high and low, by detecting temperature changes in the environment. The temperature detection range of the module is between 20 and 80 degrees Celsius. This sensor module can be replaced with a line temperature sensor for controlling the water temperature, water tank, etc. Generally, the 4-wire method of thermistor measurement is the most accurate because there is effectively no current flowing in either of the measurement cable wires and therefore no added resistance due to the cable wires. Module instructions: A thermistor module is sensitive to the environment temperature and is commonly used to detect the temperature of the surrounding environment. The potentiometer adjustment can change the temperature detection threshold (i.e., temperature control), such as the need to control the environment temperature is 50 degrees, while the module corresponding environmental temperature to the green light, the DO output high level, below the set temperature, the output high level, green light don’t. The DO output can be attached directly to the single-chip microcomputer, through single-chip microcomputer to detect the high and low levels, thus detecting the temperature of the environment change. The DO output can be directly driven by our relay module, which can form a temperature control switch and control related equipment operating temperature, also can connect the fan used for cooling, etc. The module of the temperature detection range of 20-80 degrees Celsius. This module can also be replaced with a line of a temperature sensor, used for water temperature, control of the water tank, etc.

3D Printer Temperature Detection Resistance NTC100K Thermistor Sensor Parts Hot Probe for High Temperature Filament (1 meter) This is Thermistor 100k NTC with 1 Meter Cable Temperature Sensor for 3D Printer Reprap. The thermistor is a thermally sensitive resistor known for exhibiting a large change in resistance with only a small change in temperature. The thermistor comes with a metal tip, making the temperature control more accurate, it will have a better thermal transfer and solve the problem of thermistor fixed unstable and the problem of easy damage. HT-NTC100K thermistor adopts white high-temperature cord, can bear higher temperature. And for customers' convenience, the wires adopts line connection, the customer can tear the wires depends on their application. The high-temperature line is double thicker than others in the market, not easy to break off. In 3D printers, the temperature and fine-tuning of printers are very important, as print quality can be greatly reduced if the temperature is not set correctly. The thermistor, a temperature sensor capable of withstanding temperatures above 200 degrees Celsius, is used to fine-tune the nozzle’s temperature and heat the device. In most RepRaps, a thermistor senses the temperature of the Hot End.

Thermistor Temperature Sensor HT-NTC100K- 2M NTC type temperature sensor 10K 1% with Two tinned copper wire cables consists of NTC element, SUS housing, two tinned wire cable, terminal, and temperature probe. The sensor is protected by a rubber or a stainless steel capsule, both waterproof. It is a proper solution for either heating or cooling applications. Thermistor temperature measurement is stable. The temperature measurement of the upgraded HT-NTC100K can be up to 350 degrees, can effectively replace the K-type thermocouple. It helps much to solve the issues of strict requirements of K-type thermocouple wiring, and the line is long which is susceptible to get external interference and results in temperature fluctuation that can affect the printing quality. If need to print high-temperature filament, the HT-NTC100K thermistors are highly recommended. Applications: Household air conditioner Solar water heater Refrigerator Stove Induction cooker Electric oven Home appliances Floor heating 3D printers