10K Thermistor Temperature Sensor Module(4 Pin) The 10K NTC Thermistor temperature sensor module is a low-cost, small-size module. It is very sensitive to ambient temperature. It is generally used to detect the temperature of the surrounding environment. Through potentiometer adjustment, it is possible to change the temperature detection threshold. DO output can be directly connected to the microcontroller to detect high and low, by detecting temperature changes in the environment. The temperature detection range of the module is between 20 and 80 degrees Celsius. This sensor module can be replaced with a line temperature sensor for controlling the water temperature, water tank, etc. Generally, the 4-wire method of thermistor measurement is the most accurate because there is effectively no current flowing in either of the measurement cable wires and therefore no added resistance due to the cable wires. Module instructions: A thermistor module is sensitive to the environment temperature and is commonly used to detect the temperature of the surrounding environment. The potentiometer adjustment can change the temperature detection threshold (i.e., temperature control), such as the need to control the environment temperature is 50 degrees, while the module corresponding environmental temperature to the green light, the DO output high level, below the set temperature, the output high level, green light don’t. The DO output can be attached directly to the single-chip microcomputer, through single-chip microcomputer to detect the high and low levels, thus detecting the temperature of the environment change. The DO output can be directly driven by our relay module, which can form a temperature control switch and control related equipment operating temperature, also can connect the fan used for cooling, etc. The module of the temperature detection range of 20-80 degrees Celsius. This module can also be replaced with a line of a temperature sensor, used for water temperature, control of the water tank, etc.

10K Trimpot Trimmer Potentiometer - (Pack of 5) A 10K trimpot (also known as a trimming potentiometer or variable resistor) is a type of adjustable resistor that is commonly used to fine-tune the performance of an electronic circuit. Trimpots are small, usually having a size of about 5 mm to 20 mm in diameter, and are often used in situations where space is limited. A 10K trimpot has a resistance value of 10,000 ohms (10K ohms). Trimpots are classified by their resistance value, which is measured in ohms. A 10K trimpot has a relatively high resistance value compared to some other types of trimpots. A Trimpot or trimmer potentiometer is a small potentiometer that is used for adjustment, tuning, and calibration in circuits. This potentiometer is easy to mount on a PCB and can be adjusted using a screwdriver. What are Potentiometers? A potentiometer is a three-terminal resistor with a sliding or rotating contact that forms an adjustable voltage divider.

10Kg Load Cell A 10 kg load cell is a load cell that is designed to measure forces or weights up to 10 kg (22 lbs). Each load cell can measure the electrical resistance, which changes in response to and is proportional to the strain (e.g., pressure or force) applied to the bar. You can use this gauge to determine how heavy an object is, if the weight of an object changes over time, or if you simply need to detect the presence of an object by measuring strain or load applied to a surface. This straight bar load cell is made of Aluminium alloy and can read a weight capacity of 10KG. It has four lead wires for connecting to the HX711 A/D Pressure Sensor. It is simple to use with a driving voltage of 5-10V and produces output voltage as force changes over it. Installation of the Sensor is also a simple task; it is necessary to fix one end through the screw hole and leave the other end floating in order to indicate the direction of the gravitational force exerted. Special care must be taken not to directly push the white plastic cover part of the sensor in order to avoid damage. A load cell is used in an electronic weighing machine to measure the load or pressure produced by the load; most load cells use the strain gauge method, which converts the pressure (force) into an electrical signal; these load cells have four strain gauges connected in a Wheatstone bridge formation. When we apply a load, the strain gauge resistance changes, and thus the output voltage from the load cell changes, allowing us to measure the load value. If you want to use this load cell you need few essential elements like hx711 , Arduino , jumper wires , display module and soldering tools . There are other types of load cell also available , according to your requirement Applications: Electronic platform scale Digital scale Parcel post scale Electronic balance Also check 3 Kg Load Cell with the model name YZC-133. It is designed for use in electronic scales, price computing scales, electronic platform scales, digital scales, parcel post scales, electronic balances, and various commercial scales that require a single load cell.

10kg Load Cell with HX711 Weight Sensor To measure the weight and load of any object we use strain gauges but the problem with using standalone strain gauges is that they are fragile and are easily bent and break if not used in a proper enclosure. This load cell made up of aluminum alloy can measure up to 10 kg load and outputs in the form of electrical signals proportionally. This sensor will use a HX711 Analog to Digital signal converter, it is easy to use with driving voltage 5-10V and produce the output voltage as per the force changes over it, to read and send the data to the microcontroller or development board you are using as the analog signal from the load cell is too small to be read easily. Accurate measures forces from 0-1kg; load cell specs: 22 cm (8.5 in) wire leads pre-attached. Dimensions 12.7 mm high, 12.7 mm wide, 80 mm long (0.5 in x 0.5 in x 3.15 in). 4 mounting holes, 15 mm spacing on each side. On both holes tapped m4 thread, on the other side, both holes tapped m5 thread. HX711 : This top-of-the-line load cell amplifier mounted on a breakout board pairs perfectly with the load cell to provide fast, accurate force measurements. It measures small changes in the resistance of the strain gauges mounted to the load cell and passes these values directly to any microcontroller (like an Arduino or raspberry pi). Connection (to HX711): Red to e+; black to e-; green to a+; white to a- Applications: Platform scales Electronic weighing machines Belt scales

10M Ohm Resistor - (Pack of 10) The 10M ohm Carbon Film Resistors are typical axial-lead resistors, which have much better temperature stability and provide lower noise, and are generally better for high frequency or radiofrequency applications. A resistor is a passive two-terminal electrical component that implements electrical resistance as a circuit element. In electronic circuits, resistors are used to reduce current flow, adjust signal levels, to divide voltages, bias active elements, and terminate transmission lines, among other uses. Resistor Colour Coding:

10mm Bright Green LED - 10pcs Pack The 10mm Bright Green LED - 10pcs Pack includes super bright LEDs that shine with a wide beam. They are perfect for projects, lighting up models, headlamps, spotlights, car lighting, and more. These LEDs use low power while providing strong, reliable light. Whether for general lighting or as an indicator, they are a great choice for your needs. Applications: TV set Monitor Telephones Computer Project Panel for Indicators etc.

10mm Bright Red LED – 10 Pcs Pack The 10mm Red LED is a bright light that emits red color. It is a small semiconductor used as an indicator in many devices. This LED is made for applications that need higher brightness and comes in different colors and intensities. It's perfect for use in electronics and lighting projects, providing a reliable and efficient light source. Applications TV set Monitor Telephone Computer Project Panel for Indicators

10mm Bright Yellow LED - 10pcs Pack The 10mm Bright Yellow LED is a powerful light that shines in bright yellow. It’s a small semiconductor used as an indicator in many devices and is also used for general lighting. With a transparent lens, it is designed to provide higher brightness. This LED comes in different colors and brightness levels, making it a great choice for lighting and electronics projects. Applications: TV set Monitor Telephones Computer Project Panel for Indicators etc.

10mm Conductive Copper Tape Adhesive This is a 10mm conductive adhesive tape that is manufactured from copper material. The copper material of the adhesive tape provides great conductivity and can be used for conduction in DIY projects. The tape is solderable, resists oxidation and discoloring, and withstands temperatures up to 155 degrees F. High-Temperature Heat Resistant Polyimide Koptan Tape Hot serves as the perfect combination of heat resistance (anti-creek property) and Durable Insulation. Extensive use as electrical insulation for transformer, motor, coil, capacitor, and frequency conversion power supply in electronic industry.

10mm Spiral Wrapping Band Black 10M for Wires This cable management sleeve easy installation, no other tools needed. Wrap the cable management sleeves around your cords and within a minute you can enjoy a tidy and lovable living/working environment. This spiral wire wrap provides safety, protect wires from the wear and tear, prevent electric leakage Easy to install with the thread guide and can be cut to custom lengths. It organizes and protects wires and can easily be cut off to the length you need. Put all messy wires of TV, Theater, Computers, etc. easily and neatly into one cord. Protect wires from the wear and insulation, and can improve the beauty of bending. Spiral tube wrap is mainly used in all kinds of engineering machinery and mining hydraulic equipment and electric wire and cable protection. As It can be completely covered by protection products, that protection in many rod-shaped object effectively Applications: Organize the cables coming from your desktop computer, entertainment system, or other devices that have cluttered, disorganized cables. Perfect for gathering all your cables into one manageable bundle.