18 Pin Narrow IC Base 18 Pin Narrow IC base is an 18-pin IC holder, which can be soldered directly onto the PCB. The IC can be removed from this socket when required. The IC is placed on the socket at the time of use. This base acts as a removable IC holder. The IC Base is used when the IC is temperature sensitive and the heat from the soldering iron can damage the IC. This socket is used when working with a microcontroller IC and can be removed for programming. Key Features: Moulded notch for proper orientation. Easy to insert and remove ICs. The socket is used when the IC is temperature sensitive and the heat from the soldering iron can damage the IC.

1N5408 Diode - (Pack of 10) The 1N5408 diode is called a power diode because of its high forward current and reverse voltage with a power dissipation of 6.25W. For 1N5408 Diode, the maximum current carrying capacity is 3A it withstands peaks up to 200A. Hence we can use this in circuits that are designed for less than 3A. A diode is an electrical device allowing current to move through it in one direction with far greater ease than in the other. Current passing through a diode can only go in one direction, called the forward direction. Current trying to flow the reverse direction is blocked.

1N5819 Diode (Pack of 5) The 1N5819 is a Schottky diode with a low forward voltage drop and high switching speed. It is commonly used in high-frequency applications like Inverters, DC-DC converters etc. The 1N5819 axial leaded Schottky rectifier has been optimized for very low forward voltage drop, with moderate leakage. Typical applications are in switching power supplies, converters, free-wheeling diodes, and reverse battery protection. A diode is a device that allows current flow through only one direction. That is the current should always flow from the Anode to the cathode. Applications of Diode Can be used to prevent the reverse polarity problem High-Frequency Inverters Used as a protection device Current flow regulators Polarity Protection applications

2845 3000KV Sensorless Brushless Motor The 2845 3000Kv brushless motor is a sensorless motor that is designed to provide high torque and maximum efficiency. It is manufactured with high-quality material and has a low heat production ability. This helps the 3000Kv sensorless brushless motor to have a longer lifetime. This brushless motor also features strong overload protection and protects the drone components in terms of electrical failure.

3D INKJET E3D V6 J-head Extruder Kit The 3D extruder is the part of the 3D printer that ejects material in liquid or semi-liquid form in order to deposit it in successive layers within the 3D printing volume. Extruder is considered as one of the important components of a 3D printer. It is the part of the 3D printer responsible for drawing in, melting and pushing out the filament. check out : 3mm 100g Green ABS Filament

3DR Radio Telemetry 915 MHz This 3DR 915 MHz Radio Telemetry kit set allows you to connect a flight controller and a USB or UART-enabled device, such as a computer, laptop, or tablet with USB compatibility (OTG). The latest version 2 radios no longer require a separate Air/Ground module, as both transceivers can now use both UART or USB connections, and support both modes. This radio set not only allows you to view real-time data, such as live GPS position overlaid on a map, system voltage, heading, waypoint navigation, and even an artificial horizon, but also offers much more. By using an open-source MAVlink-based ground station software, you can even fly your aircraft with a joystick via your computer and update settings in real time. Alternatively, you can use it for your DIY projects that require a wireless Serial interface. This kit is cost-effective, has a longer range, and offers superior performance. The system operates on the 915 MHz band and provides a full-duplex link using HopeRF’s HM-TRP modules running custom, open-source firmware. Features MAVLink protocol framing status documents Frequency modulation and Spread Spectrum (FHSS) Self-adaption to time division multiplexing Support LBT and AFA Configurable duty cycle Built-in error correcting code(up to 25% data bit error) AT command configure data transmission RT command remote control data transmission Interchangeable air and ground 915 MHz modules Micro-USB port 6-position Molex connector SMA connector 2-way full-duplex communication through adaptive TDM UART interface Transparent serial link Open-source SIK firmware Configurable through *Mission Planner and *APM Planner Based on the HM-TRP wireless module, with Si1000 8051 microcontroller and Si4432

3DR Radio Telemetry 433MHz 500mW(X6) This set of 3DR Radio Telemetry Module 433MHz 500mW allows you to establish a connection between a flight controller and a USB or UART-enabled device, such as a computer, laptop, or tablet with USB compatibility (OTG). The latest version 2 radios no longer require a separate Air/Ground module, as both transceivers can now use both UART or USB connections, and support both modes. This radio set not only allows you to view real-time data, such as live GPS position overlaid on a map, system voltage, heading, waypoint navigation, and even an artificial horizon, but also offers much more. By using an open-source MAVlink based ground station software, you can even fly your aircraft with a joystick via your computer and update settings in real-time. Alternatively, you can use it for your DIY projects that require a wireless Serial interface. This kit is cost-effective, has longer range, and offers superior performance. The system operates on the 433MHz band and provides a full-duplex link using HopeRF’s HM-TRP modules running custom, open-source firmware. Features MAVLink protocol framing status documents Frequency modulation and Spread Spectrum (FHSS) Self-adaption to time division multiplexing Support LBT and AFA Configurable duty cycle Built-in error correcting code(up to 25% data bit error) AT command configure data transmission RT command remote control data transmission Interchangeable air and ground 433MHz modules Micro-USB port 6-position Molex connector 250mW maximum output power (adjustable) SMA connector 2-way full-duplex communication through adaptive TDM UART interface Transparent serial link Open-source SIK firmware Configurable through *Mission Planner and *APM Planner Based on the HM-TRP wireless module, with Si1000 8051 microcontroller and Si4432 Why Choose 3DR Radio Telemetry? Real-time data transmission for GPS, voltage, and flight parameters. Stable and long-range connection with up to 250mW output power. Full-duplex communication for simultaneous data send and receive. Supports MAVLink protocol for seamless integration with APM and Pixhawk. Plug-and-play setup for drones, robotics, and remote monitoring projects. Open-source firmware allows customization and flexibility. Reliable operation even in interference-prone environments. Setup Guide: 3DR Radio Telemetry with Pixhawk/APM Step 1: Connect the air module to the Pixhawk or APM telemetry port using the provided cable. Step 2: Connect the ground module to your PC using the USB cable. Step 3: Install the required USB drivers (FTDI or Silicon Labs CP210x, depending on your module). Step 4: Open Mission Planner or QGroundControl on your computer. Step 5: In Mission Planner, go to Initial Setup → Optional Hardware → 3DR Radio . Step 6: Select the COM port for the ground module and click Connect . Step 7: Press Load Settings to read the module parameters. Step 8: Adjust settings such as frequency, air speed, and net ID if needed (must match on both modules). Step 9: Click Save Settings and disconnect after configuration. Step 10: Power on your drone — the air and ground modules will link automatically, indicated by steady green LEDs. Step 11: Confirm live telemetry data (GPS, attitude, battery, etc.) in Mission Planner or QGroundControl. Applications of 3DR Radio Telemetry Long-range drone communication and control Real-time flight data transmission for UAVs Telemetry monitoring for Pixhawk and APM flight controllers Remote environmental data collection and sensing Ground station communication for autonomous vehicles Wireless data logging for robotics and research projects FPV and UAV mission planning support Industrial and agricultural drone monitoring systems

3DR Radio Telemetry Kit 433MHz 500mW The 3DR Radio Telemetry Kit has a 433Mhz frequency band and Receiver sensitivity to -124 dBm. This 3dr telemetry kit allows you to link to a flight controller to a USB or UART-equipped device such as a computer, laptop or tablet supporting a USB connection (OTG). The Radio set lets you see live data, such as live GPS position overlaid on a map, system voltage, heading, waypoint navigation and much more. The system utilizes the 433MHz band and provides a full-duplex link using HopeRF’s HM-TRP modules running custom, open-source, firmware. Using open-source MAVlink based ground station software, you can even fly your aircraft with a joystick via your computer and update settings live! Or just use it for your DIY projects that need a wireless Serial interface. This kit offers a great low price, longer range, and superior performance. The system utilizes the 433MHz band and provides a full-duplex link using HopeRF’s HM-TRP modules running custom, open-source, firmware. Features : MAVLink protocol framing status documents Frequency modulation and Spread Spectrum (FHSS) Self-adaption to time-division multiplexing Support LBT and AFA Configurable duty cycle Built-in error-correcting code(up to 25% data bit error) AT command configure data transmission RT command remote control data transmission Interchangeable air and ground 433MHz modules Micro-USB port 6-position Molex connector 500 mW maximum output power (adjustable) SMA connector 2-way full-duplex communication through adaptive TDM UART interface Transparent serial link Open-source SIK firmware Configurable through *Mission Planner and *APM Planner Based on the HM-TRP wireless module, with Si1000 8051 microcontroller and Si4432 wireless module

2.4inch Raspberry Pi Display Hat This is a 2.4-inch 320 x 240 Primary Display HAT for the Raspberry Pi that plugs directly on top of the Raspberry Pi and displays the primary output that would normally be sent to the HDMI or Composite output. It has an integrated Resistive Touch panel, which allows the 4DPi-24-HAT to work with the Raspberry Pi without the use of a mouse. The 4DPi-24-HAT and the Raspberry Pi communicate via a high-speed 48MHz SPI connection that employs an on-board processor for direct command interpretation and SPI communication compression, as well as a customized DMA enabled kernel. It is intended to work with the Raspbian operating system, which is the official operating system for the Raspberry Pi. The Raspberry Pi's 40-way Header powers the 4DPi-24-HAT, and the 2.4" touch screen allows for simple interaction with the Raspbian operating system.

5040 5*4 Propeller CW/CCW Propeller- Any Color(1 Pair) 5040 Propellers are the perfect solution for RC enthusiasts seeking a strong, lightweight, and durable propeller option. Made from PC & Fiber, these propellers ensure optimal performance for both beginners and experts. The advanced design incorporates cutting-edge technology, providing a unique selling point for aerobatics and precision flying. Crafted with durability in mind, these propellers offer stability in various conditions, making them perfect for all RC enthusiasts. The user-friendly applications, easy installation, and maintenance, along with a unique feature, make them ideal for users of all skill levels. Available in vibrant colors - Green, Red, Grey, and Black, these propellers not only perform well but also add a touch of style to your RC Quadcopter. With a size of five inches and various color and size variations, 5040 Propellers cater to a wide age range, ensuring a perfect fit for everyone. Made to enhance your RC experience, propellers are a must-have for any RC Quadcopter or Multi-Copter enthusiast. Invest in quality and elevate your flying adventures! Features: Strong and lightweight design Comes in a pair of CW and CCW propellers Stability and shockproof features for various aerial activities Cutting-edge design for aerobatics and precision flying Easy to install, suitable for all skill levels Available in different colors for customization Versatile applications for RC Quadcopter Multi-Copter Durable and long-lasting performance Applications: The 5040 5*4 Propeller CW/CCW Propeller can be used for quadcopters and multicopters. Suitable for high-quality performance and durability in aerial applications.