Original JHD 20×4 character LCD Display with Blue Backlight This is an original JHD 20 x 4 Parallel LCD Display that provides a simple and cost-effective solution for adding a 20 x 4 white on RGB Liquid Crystal Display into your project. The display is 20 character by 4-line display that has a very clear and high-contrast white text upon a blue background/backlight. This is the great Blue backlight LCD 20x4 display. It is fantastic for Arduino-based projects. This LCD 20 x 4 Parallel LCD Display with Blue Backlight is very easy to interface with Arduino or Other Microcontrollers. The values shown on the display can be either simple text or numerical values read by the sensors, such as temperature or pressure, or even the number of cycles that the Arduino is performing.

Nokia Screen This is The Nokia screen, which is a basic graphic LCD screen for lots of applications. It was originally intended for as a cell phone screen. This one is mounted on an easy to solder PCB. It uses the PCD8544 controller, which is the same used in the Nokia 3310 LCD. The PCD8544 is a low power CMOS LCD controller/driver, designed to drive a graphic display of 48 rows and 84 columns. Though it’s an industrial module, this LCD display is extremely easy to use. The Nokia 5110 is a basic graphic LCD screen for lots of applications. It was originally intended for as a cell phone screen. This Nokia 5110 LCD Display Module is mounted on an easy to solder PCB. The Nokia 5110 LCD Module uses a Philips PCD8544 LCD driver, which is designed for mobile phones. Nokia 5110 LCD Display Module is a low-cost monochrome LCD module comprised of 84 X 48 pixels that can be used to display rich graphics and text content. This module is a revision that accepts 3-5V input. So no extra level shifter is needed. It uses the PCD8544 controller, which is the same used in the Nokia 3310 LCD. The PCD8544 is a low power CMOS LCD controller/driver, designed to drive a graphic display of 48 rows and 84 columns. All necessary functions for the display are provided in a single chip, including on-chip generation of LCD supply and bias voltages, resulting in a minimum of external components and low power consumption. The PCD8544 interfaces to microcontrollers through a serial bus interface. If you want to use this Nokia screen for your Arduino projects for that you will need  a few handy components like breadboard ,  jumper wires and batteries or power supply. Pin configuration: 1 RST  reset 2 CE chip selection 3 DC data/commands choice 4 DIN serial data line 5 CLK serial Clock Speed. 6 VCC 3.3V 7 LIGHT backlight control terminal 8 GND power negative Package Includes: 1 x Nokia Screen Specifications Brand  Nokia Model  Nokia 5110 Pixels 84 x 48-pixel breakout (Arduino Compatible) Dimensions 45x45mm Weight  5 grams

16x2 LCD (Blue) This is the 16x2 LCD (Blue), A display is required if you want to add visual output to your Arduino projects.  If you only need a small amount of information displayed, this 16x2 LCD is a good choice. The 16x2 LCD Display is a simple and cost-effective way to incorporate a 16x2 White on RGB Liquid Crystal Display into your project. The display is 16 character by 2 line with very clear and high contrast white text against a blue background/backlight. This is a fantastic blue backlit LCD display. It's ideal for Arduino-based projects. This 16x2 LCD with Blue Backlight is extremely simple to connect to an Arduino or other microcontrollers. The values displayed on the lcd display Arduino can be simple text or numerical values read by the sensors, such as temperature or pressure, or even the number of cycles performed by the Arduino.

3.2 inch TFT LCD Resistive Touch Screen Panel with SPI Interface for Arduino Mega The 3.2′′ TFT LCD Touch Display has been fully assembled, tested, and is ready to use. Install the TFT display without any wiring or soldering! Simply plug it in and load a library; you'll be up and running in less than 10 minutes! It works best with any traditional Arduino ATMEGA328 board. So add a beautiful large touchscreen display shield with a built-in microSD card connection to your Arduino project. This TFT display is large (3.2′′ diagonal), bright (4 white LED backlights), and colorful (262,000 different shades)! The TFT display has 320x240 pixels and individual pixel control. It has significantly higher resolution than a black and white 128x64 display. As an added bonus, this display includes a resistive touchscreen, allowing you to detect finger presses anywhere on the screen.

20x4 LCD Module (Green) This is an 20 x 4 Parallel LCD Display that provides a simple and cost-effective solution for adding a 20 x 4 Black on RGB Liquid Crystal Display into your project. The display is 20 character by 4-line display that has a very clear and high-contrast Black text upon a Green background/backlight. This is the Green backlight LCD 20 x 4 display. It is fantastic for Arduino-based projects. This LCD 20 x 4 Parallel LCD Display with Green Backlight is very easy to interface with Arduino or Other Microcontrollers This is a basic 20 character by 4 line LCD module. Utilizes the extremely common HD44780 parallel interface chipset (datasheet). Interface code is freely available. You will need ~11 general I/O pins to interface to this LCD screen. Includes LED backlight. Package Includes: 1 x 20x4 LCD Module (Green) LCD Module Specifications Display Format  20x4 Interface 8-bit parallel interface or serial SPI modes Operating Voltage  5V Operation temperature -20°C to +70°C Package Dimensions  5 x 4 x 2 cm Package Weight  50 grams

H102 10.1 Inch 12V 1 A LCD Monitor Introducing our 10.1-inch high-resolution LCD monitor with a 16:10 widescreen aspect ratio. With a physical resolution rate of 1280 x 800 and WLED backlight, this monitor delivers stunning visuals. It supports up to 1080P HD input, ensuring crisp and clear images. The monitor features a universal interface that allows for easy connectivity with HDMI, VGA, AV, BNC, and USB sources. Simply plug and play to enjoy seamless multimedia experiences.With its versatile compatibility, this monitor is perfect for various applications such as Raspberry Pi, Xbox, PS4, CCTV surveillance, car audio and video, car headrests, and other equipment. Experience vivid visuals with a brightness of 400cd/m² and a contrast ratio of 800:1. Whether for work or entertainment, this monitor offers an immersive viewing experience. Enhance your setup with the convenience and functionality of our feature-packed monitor. Order yours today and elevate your visual experience.

128x64 Graphic LCD -Blue Backlight The 128x64 graphic LCD display is based on the ST7920 controller, which is a popular Arduino controller. It is simple to use and works with the vast majority of microcontrollers on the market. With this Graphic LCD, you can do a lot of graphic things. You can make frames as well as small animations. This 128x64 Graphic LCD module with a blue backlight and a white foreground is fully programmable and can show a mix of graphics and text. A display is required if you want to add visual output to your Arduino projects. This 128x64 LCD display is best suited for graphical upgrades to popular 16x2 LCDs, but it also allows full graphical control. This graphic 128x64 LCD series allows the user to draw lines, circles, and boxes, set or redefine individual pixels, clear specific blocks of the display, control the backlight, and adjust the baud rate in addition to writing text. The pins of the LCD 128x64 Graphic Yellow Color Backlight LCD Display module are documented on the back of the LCD to aid in wiring it up. It is very simple to connect this LCD to the 3D printer's RAMPS controller. Package Includes 1 x 128x64 Graphic LCD -Blue Backlight Graphic LCD Specifications Graphic Type  LCD Resolution   128x64 Dots Controller ST7920 Interface 8-bit parallel interfac Dimensions  8 x 5 x 3 cms  Weight  50 grams

20x4 LCD Display Module (Blue) This is the 20x4 LCD Module (Blue), A display is required if you want to add visual output to your Arduino projects. If you only need a small amount of data displayed, the LCD 20x4 Parallel LCD Display is a good choice. The 20x4 LCD Display is a simple and cost-effective way to incorporate a 20x4 White on RGB Liquid Crystal Display into your project. The display is a 20 character by 4 line display with clear, high contrast white text on a blue background/backlight. This is a great LCD module for different types of Arduino projects. You can use jumper wires for connection and I2c interface adapter. If you want to display your results and see the output, the 20x4 LCD module is the perfect component for DIY Arduino projects. The values shown on the lcd display Arduino can be either a simple text or numerical values read by the sensors, such as temperature or pressure. A 20x4 LCD means it can display 20 characters per line and there are 4 such lines.

16x4 LCD Display With Green Backlight This is the 16x4 LCD Display, A display is required if you want to add visual output to your Arduino projects. If you only need a small amount of information displayed, the 16x4 LCD Display is a good choice. This 16x4 Parallel LCD Display is a simple and cost-effective way to incorporate a 16x4 RGB Liquid Crystal Display into your project. The display is 16 character by 4 line with very clear and high contrast black text against a Green background/backlight. This is a fantastic Green backlit LCD display. It is ideal for Arduino-based projects. This 16x4 LCD Display with Green Backlight is extremely simple to connect to an Arduino or other microcontroller. The values displayed on the display can be simple text or numerical values read by the sensors, such as temperature or pressure, or even the number of cycles performed by the Arduino.

16x4 LCD blue JHD JHD 16x4 Blue Color LCD Display is the perfect solution for your electronic projects. This LCD, based on the HD44870 controller, guarantees easy interfacing with most microcontrollers, ensuring compatibility across various platforms. Its vibrant blue color with white text, dimmable backlight, and compact design make it ideal for a range of applications, from industrial test equipment to smart homes. The efficient power consumption and versatile quantity options add to its appeal. Enhance your projects with the clarity and versatility of the JHD 16x4 LCD Display. Made to the highest quality standards.

DSO138 DIY 2.4-inch Digital Oscilloscope Kit The DSO138 DIY oscillator kit is integrated with an ARM Cortex-M3 processor (STM32F103C8) and includes a 2.4-inch color TFT display screen, that can be used as the ARM test development board.  This DSO138 Oscilloscope Kit features automatic, regular, and one-shot modes, easy to capture the moment waveform. It's easy and reliable for circuit operation. This digital Oscillator kit can display frequency, period, pulse width, duty ratio, MAX./MIN./AVG./Peak-Peak/virtual values. This boost converter is a great match for the DSO138 oscilloscope kit. It can be connected directly to the DSO138 motherboard(not included).

1.8 inch TFT LCD Module This is the 1.8 inch TFT LCD Module, This TFT LCD display Module communicates via 4-wire SPI and has its own pixel-addressable frame buffer; it can be used with any type of microcontroller. Even a very small one with limited memory and few available pins! The 1.8′′ TFT LCD display features 128160 colour pixels. This display is a true TFT, unlike the low-cost "Nokia 6110" and similar LCD displays, which are CSTN type and thus have poor colour and slow refresh. The ST7735R TFT driver can display full 18-bit colour (262,144 shades!). And the LCD will always come with the same driver chip, so you won't have to worry about your code not working from one to the other. The TFT display is soldered to the breakout (it uses a delicate flex-circuit connector), as well as an ultra-low-dropout 3.3V regulator and a 3/5V level shifter, allowing you to use it with 3.3V or 5V power and logic. If you want to use this 1.8 inch TFT LCD display Module with Arduino, in your project for that you will need few essential components like breadboard jumper wires  Package Includes: 1 x 1.8 inch TFT LCD Module LCD Module Specifications Display Size  1.8 inch Pixels  128×160 colour pixels Input Voltage (V) 3.3 to 5V Driver IC ST7735 Interface Type SPI PCB Size (mm) 62×38 Weight  25 grams